So i'm not familiar with every single atomizer on the market. They're all different in their design. One potential problem i do believe to be universal in all these devices though is an "Airlock".
Regardless of how much cotton wool has been crammed into the wells of an RTA, or whether you primed your drop in coil enough, an airlock will prevent the e liquid from getting to the wick everytime. Time and time again you either re-wick or swap out the drop in coil. Then you think "there is definitely something wrong with the atomizer".
How many times have you built a new coil, or simply re-fiiled on an existing wick, and then found all you get is dry hits and you can't figure out why ?. Maybe you eventually decide "this atomizer is no good".
The simple solution is to add more e liquid than you think you should when "priming" the coil/wick. It's not a process which takes just a minute or two. The whole idea is to let the e liquid soak right through the cotton wool, through the channels until it starts to seep out the other end of those channels, where ever that might be !. To go from a tank to a coil/wick the e liquid has to travel through the channels.
If cotton wool soaked in e liquid is at one end of the channels then that is what is causing the "airlock".
Simply put "it's "trapping" the air in the channels and causing an airlock".
You get rid of all the air in the channels by "bleeding" the system. This should be the most important part of "priming". Allowing the e liquid you've added as a primer to expel all the air from the system. Without doing this you are running the risk of successive dry hits and confusion.
So you add e liquid as a primer, let it soak into the cotton wool then add a few drops more. Then, wait a few minutes to see how far the e liquid has got. Wait for it to come out the other end because that what you should be looking for. Once you see it coming out the other end of the channels you know the system has been fully bled. And then you can reassemble your device and fill the tank.
During the "panic buying" time, I ordered a ton of Cotton Bacon Prime.
Before that, I had ordered 2 packages. Both were authentic and said "Wick n Vape" on the package.
This new order has been authenticated. But the individual packages now says "WNV" instead of "Wick n Vape.
Is it possible "Wick n Vape" changed their name to reflect the changing times?
Hmmm ......... interesting.
Hey all,
So, I've been really happy with my new setup (iStick 50w and 30w, Nautilus and Mini Nautilus). Everything has been working smoothly, but I have a problem with the replacement coils I purchased (and cannot return).
Went to go change out the coil in one of my tanks this evening. Filled the tank up as usual, made sure the air shaft and drip tip were clean, screwed on my new coil, filled the tank, and let it sit and wick up for half an hour. Took some pulls without firing, dropped it to 8w (to "step up" and prime the new coil), and immediately got a nasty burnt hit that I can still taste an hour later. Unscrewed the tank to see what was wrong, and noticed the wicking material was bone dry.
For the longest time, I could not figure out what happened, why it wasn't wicking...until I looked closer. The e-liquid holes on the replacement coil I have are TINY! The coils that came with the tanks have holes that are at least twice, maybe three times the diameter. The holes are so small that my e-liquid will not even enter them to soak the wicking material. I checked the serial number scratch off on Aspire's site and both boxes of replacement coils I have came up as authentic.
I'm displeased. $22 down the drain, now I have to rush and find a dealer who has the "correct" coils. I cannot use these coils whatsoever, and the dealer I purchased from does not accepted returns on atomizers.
On the left is the coil that came with the tank (both of my tanks came with this exact same coil, and two replacements that look exactly like it, but I've used them up and am on the new ones). On the right, the coil I purchased in a replacement pack of 5. You can see they look nearly identical, except for the size of the wicking holes. Also, the piece at the bottom seems a bit more flimsy, as you can see in the picture, it's not exactly straight with the rest of the atomizer.
So, can anyone point me to a dealer that has the coils I need? I'm afraid of ordering from somewhere and getting the ones on the right, which are useless and do not soak up any e-liquid whatsoever.
I have a smok pen 22, I have been using smoozie Maui Waui e liquid. I have to either wait a while for the juice to soak every few long hits or I have to drop some juice down the top. I tried loosening the cap different amounts it doesn't seem to help, some people said it would. I'm not sure if I need to use different E-liquid like a clear one or what, but I hate having to wait in between hits especially if I already filled the vape with juice. I tried priming the coil when I first got it there was no good there.
Two issues I wanted to fix. The first is the battery run time using the low ohm coils. Second is when the e-liquid gets to the top of the sub ohm coil housing in the Kangertech I've noticed a lot of dry hits when heavy vaping, ( I like a higher VG juice. ) I would find myself closing the air intakes and sucking hard to get the wick saturated, ( a real pain in the ***. )
NOTE: I like an airy hit and run the air intake ports full open.
So here's what I did.
I've drilled the wick holes out to 3.5mm in the Kangertech coil housing. Then built a 1.1 ohm coil with 4 strands of 32ga. kanthal, ( twisted together first ), 5 wraps around a 3.47mm screwdriver. The coil was very springy to work with but got a bit stiffer after torching t closed to 1/4" width using adjustable tweezers. I used regular ball cotton for the wick in this experiment. The coil came in at 1.1 ohm.
Primed the wick and filled tank with a little bit of juice, just below the top of the coil housing.
All I can say is WOW. The first 10 hits taste a bit crappy but after the break in, WOW.
Taste and vapor production are great. There's a bit of crackle but no pops. Crackle I don't mind, Pops I mind. The ClouporT8 counted 75 hits and now the e-juice level is just above the wicking ports by a hair and still working great with full open air intake ports.
I will add post after I've used this set up for awhile.
Curious what other think!
VapeOn
I just bought a new E Cig, the Adept Zlide kit - Adept Zlide Kit
My issue though is that within 6 hours I have replaced the liquid 3 times. It just goes down ridiculously quick, and I'm not really chainsmoking it.
Basically, how do I make the liquid last longer before replacing it, avoiding the obvious answer of "Don't vape it as much" haha. I'm not really familiar how airflow holes and wattage works, so perhaps I'm doing something wrong with that part of the E Cig. I've got my airflow fully open at the moment though, could that be why the liquid is going down so fast? Does more airflow cause more liquid to be used?
I'm using a 1.6ohm coil and my wattage is set to 14, which is the second lowest. Does less wattage use less liquid? Not sure if it's one of these or a combination of the two that is making the liquid go down so fast.
Thanks guys.
Hey there guys, new here.
I have a Vappresso Revenger Mini kit and I have upgraded my tank from NRG SE Mini tank to a "Geekvape Z Sub Ohm tank(Much Larger Tank)". Because I wanted to taste more flavor and still blow lots of clouds in the air with my vaping device being fairly cheap.
I put a New Geekvape Z series coil 0.4ohm 50-60W because I burnt my original 0.2 Ohm coil , I wont talk about my previous coil. I'm getting 2 problems here.
1. I'm using 60W, normal setting and every time I vape or inhale I get a taste of E-Liquid in my mouth. However its blowing perfect clouds and still getting an amazing taste but its just that the liquid drops in my mouth. I just want to spit it out every time. How do I fix that problem?
2. The other thing is if I use Higher Wattage and High settings the liquid pours out of the air flow and starts leaking and backspits in my mouth.
(Before I vaped with new coil)I put the new coil in, I soaked it for 10-15mins, while I fill half tank of E-liquid which is 0.8Ng/0.2PG. Then I inhaled 3-4x with no button pressed. Then I vaped to test, still leaking. I set the vape to 70W and high setting then blow downwards into the device 5-6x. All I was trying to do is desaturate it. My results got better didnt notice much of a leak but I still get a little bit of liquid in my mouth. If you can help me out here, I would much appreciate it.
Thank you and kind regards
Tuatara Vaper
ok ... so there was a thread that showed insect droppings in some cotton someone got with a RBA ... but I can't seem to find it.
So I thought I'd have a look at the cotton sample in my Kanger Subtank Mini & .. sure enough ... bug bits & little black "dots" (bug poop I assume). Okay ... fine ... I've not used it & will not use it. I have enough cotton (bacon) to keep me going for years, and I'm happily puffing away on the .50ohm OCC premade coil supplied by ........
........and then it dawned on me that it was supplied by the same folks that put a wad of bug-gunk-ridden cotton in the box with my ST mini ... Kanger.
So ... the question is if anyone has taken apart the OCC coils & found little black specks in the cotton, or other foreign "pieces" ?? I'm wondering if the cotton Kanger uses for the OCC coils is the same cotton they give you in the box to wick the RBA deck with.
I was looking around at wicks and decided I finally wanted to try Rayon.
The fun part is, I started looking on eBay and noticed a small inconspicuous baggy (o.o!)
It appears exactly the same as a small bag I got as a sample from ordering from a few places-
Cellucotton 100 Rayon 36 ft 3 Packs Unbleached Cotton Vape Atty RDA RBA Wick | eBay
Looks exactly like this! But no label!
It was a "Freebie" so I have no idea, the note that came with it was "Here's some wick for you to try! Thank you for ordering!"
So...how would I tell if it's rayon or just cotton?
What is your go to single coil build in terms of gauge wire, diameter, and number of wraps : (no fancy Clapton or twisted build just a "regular" wrap)
And if you have a reason please include it: For example: "I'm a flavor junkie and this is best flavor build I've found" or "I like short ramp up times" etc ...
(I know preferences may vary greatly)
Thank you very much
:
Sent from my iPad using Tapatalk
One liquid and a little vloggy: [Moderated]
Come like subscribe comment don't be overly critical and sorry if this is in the wrong catagory