Lost Flavor, Mtl

Hey guys what's up?! I just bought the Innokin Kroma R mod with the Ajax tank and I was wondering what other DTL tanks I could buy that would properly fit the mod. The Ajax tank is 24mm so I'm looking for something similar that has great flavor and longevity when it comes to coil life. Please help me out guys!

Thanks,
Brian  

74 days without a cigarette so I’m still new to this whole vaping thing.

Started with Juul, got tired of refilling pods very quickly.

Switched to a Smok Nord. Have grown tired of the hit/miss with cools.

Just got my Zenith tank. Went ahead and got the Kroma/Zenith kit and it’s my first non-pod setup.

Like it so far. Only issue so far is there seems to be a lot of juice coming through when I take a hit. When I take a drag but put a thin white piece of cloth over the tip there is a very noticeable amount of brown stain on the cloth. Had the same issue when I got my Smok Nord but I corrected by switching from 50/50 nic salts to a 70v/30p freebase.

Currently Using the same 70vg/30pg 6mg Halo Tribeca.

Using the 1.6ohm coil;
Started at 14 watts;
Dropped to 11 watts and it reduced the juice but also the temp of the vape.
Adjusting the airflow doesn’t really make a difference.

Anyone else having the same issue with the amount of juice coming into their mouth? Is this normal with this type of setup? Did I flood the coil or something? I primed it with 5 drops then let it sit for about 10-15 minutes before taking the first hit.

Will probably limit it use at the house because I don’t want to carry around so much weight in my pocket.  

Hey there guys, new here.

I have a Vappresso Revenger Mini kit and I have upgraded my tank from NRG SE Mini tank to a "Geekvape Z Sub Ohm tank(Much Larger Tank)". Because I wanted to taste more flavor and still blow lots of clouds in the air with my vaping device being fairly cheap.
I put a New Geekvape Z series coil 0.4ohm 50-60W because I burnt my original 0.2 Ohm coil , I wont talk about my previous coil. I'm getting 2 problems here.

1. I'm using 60W, normal setting and every time I vape or inhale I get a taste of E-Liquid in my mouth. However its blowing perfect clouds and still getting an amazing taste but its just that the liquid drops in my mouth. I just want to spit it out every time. How do I fix that problem?

2. The other thing is if I use Higher Wattage and High settings the liquid pours out of the air flow and starts leaking and backspits in my mouth.

(Before I vaped with new coil)I put the new coil in, I soaked it for 10-15mins, while I fill half tank of E-liquid which is 0.8Ng/0.2PG. Then I inhaled 3-4x with no button pressed. Then I vaped to test, still leaking. I set the vape to 70W and high setting then blow downwards into the device 5-6x. All I was trying to do is desaturate it. My results got better didnt notice much of a leak but I still get a little bit of liquid in my mouth. If you can help me out here, I would much appreciate it.

Thank you and kind regards

Tuatara Vaper  

The coolfire z50 kit is the vape device that helped me quit smoking and start vaping one year and one month ago...it was a good choice cause I had no problems on my first vaping steps making the transition pleasant...

The z80 kit seems an impoved version in every way from the great z50 kit in my opinion...

Removable battery is always good to have....bigger size make it better to hold in the hand...very lightweight but also feels sturdy....great machining always from innokin and buttery smooth threads on the battery cap...

I still don't know if the Fourier vape tech with the new board can improve the coil life or the refresh makes any difference but I always like to see innovation and the mod performs very good that's for sur....the z coils already for me are great coils and very long lasting anyways ..

I also saw the 0.8ohm coil has bigger juice holes now!!!! I don't know since when this happend cause i have a stock of older coils and I also rebuild them...

I always thought the juice holes were kinda small for the 0.8ohm coil and sometimes on colder temps it couldn't keep up to wick 70vg juices in my opinion if u chain vape
I am very happy innokin doesn't settle and still making improvements and fine-tune their coils even tho they are so successful...

The zenith 2 is an improved zlide tank in my opinion maybe they chose to name it zenith caus the old zenith is a legend hahahaha
In fact is so similar u can swap the bottom airflows from the zenith 2 to the zlide if u wanted

its same dimensions as the zlide if u don't count the curves on the airflow ring and topcap,those curves btw make it look soooooo good

....it has wider chimney inner diameter that helps for direct lung vaping and it's not much bigger to affect the mouth to lung flavour in my opinion.....

it also comes with larger juice capacity cause the twist topfill mechanism that borrowed from the zenith takes less space and makes the tank be able to hold more juice than the zlide on same dimentions oh yeahhh....

the new airflow system is perfect....with small holes to be able to fine tune mouth to lung from tight to airy and a big slot to wide open and vape direct lung...

In my opinion is not just restricted cause it can be almost as airy as for example the hellvape destiny rta that is single coil direct lung rta.... The zenity 2 can supply the 0.3ohm z coil with all the air it needs and Vapes great...something that the zlide couldn't keep up...

 

So....been vaping for 6 years.

For the last couple years I was using a Reo with an RBA at .5 ohms and was going through about 12-15ml a day. A friend of mine let me try his sub ohm tank a few weeks ago and I was hooked! The flavor was better than my Reo/RBA setup and the vapor was OMG.

Anyways, I've since bought a couple of sub ohm tanks with an IPV2 Mini, then graduated to a Goliath RTA with an SX Mini M Class. Using the Goliath with a .44 ohm dual coil at 30 watts on the SXM and I'm going through anywhere from 25-35ml a day! This just seem excessive....

Can anyone recommend an RTA that would use less juice but still give me a lot of airflow and flavor? I'm not all about the vapor, although I do enjoy it.

I'm guessing that if you want lots of airflow (I'm a direct lung inhale kinda guy) and a warm, full vape you pretty much have to vape at higher wattages/lower ohms and therefore use excessive amounts of juice...just wondering if anyone else has had a similar experience and has successfully cut down their juice consumption.

FYI, I DIY my juice so cost is not really an issue...I'm a bit concerned that using this much juice every day just can't be good for you.  

Hello.
So I think i kind like a cooler vape been getting some heavy lung feeling lately been vaping a 1.2 ohm single coil 28 g kanthal
cotton wick on kayfun clone v4 Tobecco, i would like to try like maybe 1.8 or a 2.0 ohm coil or is the kayfun v4 really better for
lower ohm coils I keep reading where the kayfuns sweet spot is like 1.2 - 1.5 i did lower my wattage from 14 to 12 but i like to seem some clouds more of a flavor chaser than a cloud person though
so i am just wondering if anyone has tried a kayfun around 2.0 ohms and what the vape was like
thank you  

Looking for a new non sub ohm tank. I have a few sub ohm tanks and just can't get into it. It's just not for me. I enjoy a flavorful, cooler mouth hit rather than huge low flavor lung hits. I am currently vaping my old nautilus mini and still like it but I am starting to get some chest pains. It may be my juice or just me but something about the coil fill material just makes me uneasy. I'd like to get a tank that performs like the natilus mini but has a better more pure coil fill material. Any suggestions or am I looking for a unicorn?  

I just got a Delta II tank as an entree to sub ohming after a disastrous adventure with a MELO. Strangely enough, though, while blowing an occasional cloud at 30 watts is fun, I find I also like running it with the air flow pretty restricted on the tank and at 14-16 watts on the regulated mod and taking mouth hits. Really nice flavor and "just right" (to me) vapor production.

Is running a sub-ohm coil at low wattage potentially causing any damage to my mod (iStick 30w) or my tank?  

Hey. I have a very annoying dry hit problem with my Innokin Zenith tank. I can't figure out what makes it happen. It happened on an used coil, so then i changed coils, but it happened again on the new coil.

I have 30% PG 70% VG liquid, didn't chain vape too much, had it on 14 watts, the tank was full, i had primed the coil...

Help is very appreciated!  

I am trying to get the best flavor with the best single coil build.

Objectives:
Flavor Smooth Vapor
Materials:
Kanthal Wire 35mg Nic Salts
I have noticed that either depending on the diameter of the coil or the spacing of the coil wraps You get a different kind of vape hit. It seems like higher gauge wire produces a smoother hit. And then couple that with a small diameter coil build, plus squishing the coil together to remove all coil spacing results in the smoothest possible vapor.

Can anyone confirm my findings? Or does anyone have any tips because I have still to replicate the smooth hit from clearomizer sub tank cartridge's that are non mesh. I am starting to think this is because the cotton is wrapped around the outside of the coil instead of being shoelace through the middle of the coil.