Crown 4 Mesh Coil Issues

Starting from a clean - authentic nautilus mini - with a brand new 1.6 (or 1.8 it makes no difference) coil (coils also verified as authentic).

1. Turn tank upside down - with tip removed and fill with juice.
2. Take base unit and set so no air holes are open.
3. Put a tiny bit of juice around the o ring of the base unit (i get the issues if I do this or not)
4. Put 2 small drops of juice into the coil (I get the issues if do this or not)
5. Screw the coil into the base unit (as tight as you can comfortably get it without going past the obvious stop point and damaging something)
6. Screw the coil/base unit into the tank.
7. Turn nautilus mini correct way up.
8. Move air hole to a middle setting.
9. Take some primer puffs with no power.
10. Leave standing for 5-10 mins.
11. Begin vaping gently at 6 watts - moving up slowly to 10.

Ive tried all types of juice - both high VG and high PG and in-between. Invariably at some point i start to get the gurgle. Ive tried the following fixes:

1. Using a paper towel blow gently out of the air hole to get rid of juice - doesn't work - if i kept on blowing id blow the whole tank of juice out.
2. Take the unit apart - most times there will be juice in the base unit underneath where the coil sits - dry this out - dry the coil off and repeat from step 2 above missing out steps 3 and 4. - this sometimes works but its a temporary fix.

There seems to be no pattern to the problem. Sometimes the gurgle starts as soon as ive changed the coil - sometimes its ok for a week. I have 2 units and 2 spare tanks and have rotated them all using the above method - still get the issues.

I have actually never experienced the burnt taste or reduced draw because Ive always got sick and binned the coil before that point.

I am vaping generally at 9.2 watts - but have tried as low as 7 and as high as 13 - it makes no difference.

I don't draw hard - I cannot understand why I keep getting juice in the air chamber - its not a problem with a "dud coil" unless they are all intermittently dud coils - they are all authentic aspire and I've bought them from different places - so its not a dodgy batch issue - the rings are all the correct way up - I have spent hours and hours researching to try to fix these issues - and cannot for the life of me maintain a stable nautilus mini.

Can anyone save me from madness and tell me what Im doing wrong - Im tending towards a conclusion of all nautilus mini components are junk at the moment.

Many thanks in advance  

So I finally got around to putting a coil on the rba deck...my typical kayfun build, 28 ga @ 1.3-1.4 ohms. Everything looked good, coil tight....raised off the deck...screwed into the ohm meter....weirdness ensues....said 3.85 ohms...took it off, put it back on...said 4.6 ohms....looked to see if the coil screws were tight ...check. both tails tight under the screws...check. The coil deck screwed into the base...yep. No moisture in the base, nope. Put it on the ipv...said 7.7 ohms, then 4.2, then 3.90.............


Put the stock coils in the base, everything normal. Is there something I could be missing in the coil deck??? I got nothing else. No, I had not put the chimney on, so no short there. I may wrap another coil and see....I can only think that something is amiss in that little coil deck....or I am missing something in the build that is obvious. It's a really nice, tight looking coil too.  

I'm so tired of the recent "mesh only" craze. I just don't understand it at all.

I have used roundwire sub tanks for close to 4 years, and can generally get a pretty accurate flavour representation from my juices. Obviously some are better than others, but the og Uwell Crown coils and .4 Cleito coils are pretty stellar.

Recently decided to mix it up and try something new, so i went on the hunt for a new sub tank, only for the market to be completely littered with mesh-only tanks. The only tanks i could find that still use roundwire are from years ago.

I figured i had been missing something, so i picked up a collection of mesh sub tanks, only to be dissapointed by every one of them.

The list was:
Ehpro Raptor with both the raptor coils and the Horizontech Falcon coils.
Innokin isub B.
Aspire Odan Evo.
Aspire Cleito Pro.
Geekvape Zeus.

I got absolutely zero of the liquid nuance that i get from 3+ year old roundwire coils. I just get a blast of full-on "all the flavours at once", and for juices with sweetener, that is the primary profile. Interestingly, i found that with fruit flavours, it was a little more palatable, but since i primarily vape bakerys this wasnt all that much use.

I figured i would give the mesh rta's and rda's a shot, as everyone is raving about them, so i picked up:
Wotofo Profile RDA.
Wotofo Profile Unity RTA.
VandyVape Mesh RTA.

Tried all of them, same dissapointing experience. They were basically mesh sub tanks in RTA form. Literally exactly the same "flavour".

So, after wasting a chunk of money on all of these, im back to using the Cleito Pro with the 0.4ohm Cleito coils and the Uwell Crown Mini with the og Uwell Crown coils with the occasional use of the Wake Mod co RTA when i can be bothered to rebuild.

Is it just me? I dont understand the hype in any way. Maybe it's just my particular flavour profile doesn't work great with mesh, or maybe its just me, i dunno. It's just a shame to see that any recent sub tanks that come out are all mesh, apart from the very occasional sprinkling of roundwire thrown in here and there.

Anyone else have a similar experience? And have any recommendations on recent sub tanks to try that aren't just mesh?  

I have the Smok xPro M80 plus and I have a couple Kanger subtank minis I use with it. I usually use .5 ohm coils. Sometimes it will show the ohms fairly correctly at .54 or even .61, which seems close enough. However, as I puff, the ohms reading will tend to change after every few puffs. Sometimes it will even say up to 1.5 or 2.0 ohms on the same tank coil! One tank seems to do it worse than the other, but the two I use now both will change quite often, and once in awhile quite drastically. It sometimes helps if I unscrew the tank and screw it back on, but if it isn't really tight, the ohms read are really far off from what they should be. I'm not sure if it is the tanks or the M80 plus that has the problem. When it reads really high, if I don't catch it before I take a puff, it is horrible and burny-dry, since it thinks the ohms are so high...

Has anyone else had this problem and/or have any ideas as to how it can be fixed??

By the way, I've cleaned the connections and everything thoroughly, so it's not that...  

I am new to the mod world and I entered the foray with an IStick 30 and a Kanger Subtank Mini. When I use an old cheapo tank that came off an earlier Ego my juice taste fine. It's a 2.7 ohm coil set at 7.5 watts at 4.5 volts.The problem is the taste with my Kanger hooked up. It is very harsh. I also do not get the same visible exhaust (sorry, but I can't think of another term ) I operate it at about the same watts. I have tried both a sub ohm coil and a 1.2 ohm coil. I have also tried different air intake settings. One thing to note: The cheapo tank gives me a much tighter draw (It's harder to draw in the air). I have adjusted the Kanger down to the smallest inlet and the resistance still seems very easy.

Would the difference in resistance of the coils affect the taste with running the same power. Do some juices just not taste good with different tanks? I must be doing something wrong. Maybe I assembled it wrong by leaving out something but for the life of me I can't see what? I did insert a little piece of cotton in one of the coils which was foreign to me.

Any ideas? Fire away and don't assume anything. Again, I am ignorant with these mods so I am learning here. Thanks a bunch  

Im new to external battery mods but have been vaping for 3 years and I know how to prime a coil with e-juice. I go the extra mile after I prime the coil and let it sit for a minute. Then I fill up the tank put it back together and do not touch it for at least an hour or two just to make sure. I just got my now verified as legit sigelei sobra with the moonshot 120 both of the coils from that taste like those knock off BS eBay fake coils. I started off at a very low wattage and I don't know what's wrong both coils are disgusting. It's not exactly a burnt taste or a dry taste it's like a sour off taste and I can't use them. It also makes me feel like I have something in the back of my throat. What in the heck is going on? Do these coils take awhile to become usable? They're the coils that came with the mod and I verified the mod so I assume the coils are also okay. I even went so far as to try the second coil on a different mod but with the same tank just in case the mod was frying things the very first hit. Can anyone give me an idea of what's going on so I know what I need to do and also if anyone could tell me whether or not the Cascade baby coils will fit in the moonshot 120  

okay, so i had a problem yesterday where i would keep getting juice popping up on the draw, that problem is solved, however, now on only the second day of light use, on the 1.2 ohm coil that came with the tank i am getting a pretty harsh smokey taste. Its not overwhelming like it is when a coil is burnt out, just an unpleasant taste. I did 4 drops of liquid on the coil before using, everything is screwed in tight. Do i need maybe a couple more drops on the coil?

FYI: using an istick 30w burning at about 14.5-15w  

Hi I've been in the vaping industry for years now and have had many tanks over the years both mesh and normal coil, for me mesh was amazing at flavour and for more cooler vape lovers, however I found that normal coils provided more cloud and less juice consumption with some tanks and were able to achieve the same amount of flavour as mesh with the right build. But I still curious as too how many people prefer mesh over normal coils and vice versa and why ?  

It's often been said to test a new coil build on a regulated mod before using it in a mech mod. Just for fun, I tested a new build on multiple platforms to see how consistent they a

These are AVS stainless steel premade quad core clapton 30x4/40 3.5 7/6
Two coils in a Dead Rabbit V2 RDA

Coil Master Tester 0.17
Uwell Crown mod 0.19
Wismec mod 0.18
Geek Vape Aegis 0.18
Vapresso Luxe 0.18

Closer than I would have thought!

Incidentally, the old coils were in there for 8 months, although this unit is in rotation, so maybe a months worth of actual use.

Also, the top cap was just about impossible to remove from the tube. I had to insert a chap stick into it and slam it on the desk for it to come off.  

Hey guys whats up. Well I had gotten the Sub Mini tank, the first tank I got was a dud. I had nothing but issues with it since day one. Coils went bad in 1.5 days both coils, then the rba deck was giving my sigeili issues and errors.

So I sent it back, They replaced it, and I now have Version 2 as they say. This tank has 2 air slots and different Holes in the tank. I used the Stock .5 coil but was just getting wayyyy too many dry hits.. So I went to the RBA deck, been using the coil that came with it, and I have 100% organic cotton. So I been using that, but now I am getting Dry hits with this thing!!! every 4th hit Is Dry!! I have to cover the holes and pull to get teh cotton wet again, and then 4th hit shes dry again.

What is going on here? Anyone else have issues like this? I am really getting fed up with this and ready to just throw it away. What can I do about the situation or why is this happening?

E-juice = 80/20 Clear Liquid all fruity flavors 3MG