Vype Etank Pro 2

I have an orbit cannon vape pen. I believe it's 510 style.

I bought it 5 months ago. I just got around to using it. You press the button 5 times, and it turns on, press it 5 more times and it shuts off. The light also indicates the battery voltage. It turns white when fully charged, and then blue, and then red when it's almost dead. There is also a light on the charger that is red while it's charging and then it's supposed to turn green when it's done charging.

Well, the e cig battery light stays white for a short while, and then turns blue. It used to stay white longer. It's like after a short bit of usage, it goes blue. The red light on the charger also never turns green no matter how long it stays plugged in.

The e cig stayed in the box, and the battery was depleted. I picked it up a few days ago and put it on the charger to start using it and noticed this.

Does it sound like the battery is messed up? Last night I charged it 3 hours and the red light on the charger never turned green so I unplugged it. The light on the battery was white. Today I went to use it, and the light was blue - I never used it and the e cig itself was turned off.  

Hi, I'm new here and have searched but couldn't find an answer so help appreciated. When charging my MVP4 no matter what the state of charge when I put it on charge the button shows RED. It stays RED and as the charge builds turns GREEN and then goes out when full. I.e. It never goes through AMBER which all my previous batteries have. Is this normal?  

As the question speaks for itself, I’ve run into this scenario a few times specifically with vype. Every now and then, every puff since the first one tastes like a burnt and already used coil. It seems to happen in 1 in every 5 pods or so. Is this just bad luck, or is could it be a possibility they are reusing pods to save money, and if it were the case, would it be considered illegal to sell already used pods?  

So I recently bought a brand new Vaporesso Gen mod. Normally I stay away from compression/press fit 510 connections but I decided to give the Gen a shot. I've only had it 1 day, and already I've noticed that the 510 connection is raised slightly above the top of the mod and with a tank connected it is slanted towards the back of the mod. From what I can tell the 510 isn't loose at all. But it still slightly worries me. And a couple times I've taken a hit and everything is fine. Then all of the sudden while my finger is still pressing down the fire button it stops firing. Has anyone else experienced this with the Gen?  

I bought a brand new freemax twister 80W kit and when i connect it to the charging port the blue ligt flashes then theres no light to show that it is charging, what may the problem be???  

Hey guys,

I finally updated my charger a few days ago (I think before I had the VP2) or something like that. Quick question on something I'm noticing that seems a bit odd to me.

When I charge (for example 18650's), a battery that's fully charged in channel 1...it flashes FULL/0.00 mA, I remove the battery. A few minutes later, I'll put the battery back in the same bay, and all of a sudden there are a few hundred mA's that show up on the screen that need to be charged back into the battery and it takes a few minutes for channel 1 to recognize the battery is fully charged and flash FULL/0.00mA again (although it does show above that's fully charged at 4.2v).

If I take that same battery and do the same test but this time in channel 2, within a few seconds it recognizes that the battery is fully charged and flashes FULL/0.00mA. So it seems channel 1 is not working as well as channel 2 is, when it comes to recognizing information from the battery.

Is this normal for this charger or do I have a defective charger?  

I have a few dollars invested in vaping (subohm set ups) . I was out town for the past two months working and I ran out of juice and all I had accessible to purchase were those little vype pods and I was quite impressed with the nicotine satisfaction I received from it , but now I'm back home and I've got ample everything I need but I find myself going back to my left over vype pod . So now I'm confused do I need to switch vaping style or equipment ,I don't feel like reinvesting in all new stuff my girlfriend will kill me. Did that happen to anyone else ? How did you handle it? Thank you  

I am new to vaping. I am starting out on a kanger protank mini3. I recently replaced the coil, cleaned it, reassembled and changed out the juice. My problem is that every few hits, it tastes really bad. I read that it could be a dry hit, so I tried to work on that. I did dry burns and primed it without pressing the button. I even loosened the coil slightly making sure it had good air flow. I am completely befuddled. It's not constant, just every 6-8 hits it so. Any advice would be sooo appreciated. Thanks!  

Hey guys, can anyone help me troubleshoot with a Vype Epen 3? There is no response no charge no nothing. Not sure if it’s me or it’s faulty from the off. Thanks in advance.  

I accidentally locked the up and down buttons by pressing both of them simultaneously for 2 seconds, I have tried unlocking them by doing the same thing like the instruction manual calls for. It doesn’t work, no “unlock” pops up or anything. You can hold them as long as you like and...nothing.

I have since figured something might be wrong with it as I am almost positive I’m doing it correctly. Now I have tried getting the reset button to work in hopes of the up and down buttons being unlocked upon reset. I hold the reset button for 5 seconds and I’ve tried the method of the combo with the fire button and reset as well as the up arrow and reset and the screen goes blank and turns back on but never says reset and the settings are still the same as before.

My next idea is plugging it into my computer in hopes of an update fixing this but other than that I am out of ideas. The device is stuck on 20 watts which is too high for the cartridge I’ve got on it. Does anybody have any ideas, please help me out.