Smok Tfv12 Prince Rba Issues

First off, I would like to say that I’m very new to vaping. I started off with a JUUL, then a Smok Novo 2, and eventually got sick of buying pods.

Now I have a Hellvape MD, and an Ares 2 - the first provides better flavor, but it’s still not comparable to what I was getting in my pod systems. I just recently purchased a BP Mods Pioneer, and I’m hoping that gives me better results. I’m using an Aegis Mini for a mod.

I’m trying to figure out what I’m doing wrong, because it’s really frustrating to spend all this money for worse flavor, when I was hoping it would let me save money.

I have about 40 bottles of salt nic flavors that are 50 or 35 mg, and a couple 3mg freebase I bought (120ml for $7 seemed like a steal). I would really like to get away from the salt nic, but I seem to get even worse flavor from the 3mg.

I’m using 2.5ID 28ga SS316L round wire from Master Wire Supply (I have a spool) with Puffs Organic Cotton. My coils are usually .7ohms, but I’ve tried up to 1ohm. I’ve also tried 1 ohm Vandy Vape Superfine MTL fused claptons, and experienced similar results.

I’m using the MD with the most restrictive airflow settings (3 small hole airflow disk), low (2-3) adjustable AFC setting. I have my coil as low as possible to the airflow, and I have thinned / fluffed my wicks.

I haven’t tried adjusting the airflow below the coil on the Ares 2, because the video instructions say wide open airflow below the coil is the best for flavor (I have found the opposite to be true for the MD).

Can someone provide me more insight?

Will 2mm ID coils with the same amount of wraps taste better than 2.5? Do coil ohms do anything for flavor, or does it only change how fast it heats up? Will I lose flavor if my coils hang outside the diameter of the airflow disk?
Is there a certain type of coil that would give me better flavor than regular round wire?

I use TC at 420F 20 watts


Any kind of feedback is appreciated and if I left anything out or you have questions about my set up that could help me out please ask! I’m at a loss on what to do, and it seems like no amount of research is helping  

Just bought the Kangertech Subtank..... Was told I couldn't use my Max VG juice and I needed to buy some of their lower VG juice. I told the guy no thank you, I know what i'm doing and I can make it wick the Max VG.

Needless to say I got home, the STOCK OCC coil, .5 ohm, wicks my Max VG perfectly fine, even with chain vaping.

I ripped the pre-made coil out of the 1.2 ohm OCC head, and built my own .6 ohm coil in it, wicked it with Organic Cotton (Not KGD or Bacon, Just organic cotton from Walgreens) and it wicks perfectly fine with my Max VG.

I built a single coil .7 ohm spaced coil, wicked it with the double tails on each side, cut off to where it touches the deck, but not touching the threads, put the chimney cap on, and made sure the juice channel was free of blockage, and it wicks perfect with the Max VG.

No leaks, no dry hits, running each OCC head at 30 watts, and the RBA deck at 35 watts.

This is the original Subtank, 6ml for OCC and 4.2 for RBA, (NOT THE NEW 7.0mL version).

So let me hear it.... What have you guys noticed or seen about the wicking ideas, why has yours not worked?

WHY DO SO MANY PEOPLE SAY YOU CANT USE MAX VG ON RTA's, especially on the Kanger Subtank????  

I have been using an evod for two years now. Yeah, I know, minor leagues, but it gets the job done just fine for me.

For the first 18 months I was constantly buying new coils. I work from home so I can basically vape all I want and I vape A LOT. I use Swagger as my ADV and it will destroy a coil in just a couple days. It was becoming difficult to even find coils to buy and it was getting expensive, so I did some research on rebuilding my own coils. At first I tried to build them with silica wick, but I could never get them to work right. Using 1mm silica wick wrapping around a stick pin the wraps would always be too big and there was lots of leak/gurgling. So I went the cotton route and would wrap around a 1/32 drill bit and then slide the cotton through the coil. Works great, perfect ohms, great flavor. I've been doing this for the past six months. In the first 18 months of vaping I never got sick once. Since I've been using the cotton wicks I've been SEVERELY sick twice (probably a respiratory infection but never went to the Doc), and now I feel like I'm getting sick AGAIN.

I've noticed that I can see little flecks of what looks like cotton building up on the mouthpiece, and I'm assuming, going into my lungs. I think this is what is making me sick--the buildup over time. Anyone else had issues with this? I think I may have reached the end of my rope with vaping and now maybe I'll do what my original intention was (quitting altogether after vaping for a short period of time).

Anyone have any tips on rebuilding coils with silica? I've watched a million Youtube videos and replicate the process perfectly, but the wraps end up being twice the size they should be and I've been unable to slide silica wicks into the coil like I do with cotton because even at 1mm it's too big to fit through the hole. Thanks for any help.  

Hey guys whats up. Well I had gotten the Sub Mini tank, the first tank I got was a dud. I had nothing but issues with it since day one. Coils went bad in 1.5 days both coils, then the rba deck was giving my sigeili issues and errors.

So I sent it back, They replaced it, and I now have Version 2 as they say. This tank has 2 air slots and different Holes in the tank. I used the Stock .5 coil but was just getting wayyyy too many dry hits.. So I went to the RBA deck, been using the coil that came with it, and I have 100% organic cotton. So I been using that, but now I am getting Dry hits with this thing!!! every 4th hit Is Dry!! I have to cover the holes and pull to get teh cotton wet again, and then 4th hit shes dry again.

What is going on here? Anyone else have issues like this? I am really getting fed up with this and ready to just throw it away. What can I do about the situation or why is this happening?

E-juice = 80/20 Clear Liquid all fruity flavors 3MG  

74 days without a cigarette so I’m still new to this whole vaping thing.

Started with Juul, got tired of refilling pods very quickly.

Switched to a Smok Nord. Have grown tired of the hit/miss with cools.

Just got my Zenith tank. Went ahead and got the Kroma/Zenith kit and it’s my first non-pod setup.

Like it so far. Only issue so far is there seems to be a lot of juice coming through when I take a hit. When I take a drag but put a thin white piece of cloth over the tip there is a very noticeable amount of brown stain on the cloth. Had the same issue when I got my Smok Nord but I corrected by switching from 50/50 nic salts to a 70v/30p freebase.

Currently Using the same 70vg/30pg 6mg Halo Tribeca.

Using the 1.6ohm coil;
Started at 14 watts;
Dropped to 11 watts and it reduced the juice but also the temp of the vape.
Adjusting the airflow doesn’t really make a difference.

Anyone else having the same issue with the amount of juice coming into their mouth? Is this normal with this type of setup? Did I flood the coil or something? I primed it with 5 drops then let it sit for about 10-15 minutes before taking the first hit.

Will probably limit it use at the house because I don’t want to carry around so much weight in my pocket.  

I have my Aspire Nautilus on my iTaste MVP 2.0 at 11 watts, running a 1.6ohm coil. I have also used it on my Nemesis mech mod with either an LG HE2 or a Sony VTC5 (I already know that mech's aren't ideal for tanks, but it was working really great). Everything has been fine, but now I'm noticing a bit of gurgling. Am I just under-powering the coil?  

Hi guys,

Is it really normal for an atomizer to get hot especially when using dual coils?
I just created a dual coil a couple of minutes ago using 24 gauge kanthal wire, 10 wraps each on a 2.4mm precision screw driver. My meter shows that the resistance is at 0.4 ohms, being curious and all since this is the first time that I made a dual coil, i decided to test it out.
Got some good flavor and vapor, though the vapor is warmer than I would want it to be ( I prefer cold vapor)

After taking a couple of 5 secs drag, I notice that my atomizer became hot, not warm, but hot. Is this something that I should be concerned about? I am doing something wrong or have I done something wrong when creating my coils?
Please help.

Here are some pictures of my device and atomizer. ( Philbox wood mod running on 2 pcs of AWT 18650 2600mah battery, my atty is Haze by vapehead origins)


 

Starting from a clean - authentic nautilus mini - with a brand new 1.6 (or 1.8 it makes no difference) coil (coils also verified as authentic).

1. Turn tank upside down - with tip removed and fill with juice.
2. Take base unit and set so no air holes are open.
3. Put a tiny bit of juice around the o ring of the base unit (i get the issues if I do this or not)
4. Put 2 small drops of juice into the coil (I get the issues if do this or not)
5. Screw the coil into the base unit (as tight as you can comfortably get it without going past the obvious stop point and damaging something)
6. Screw the coil/base unit into the tank.
7. Turn nautilus mini correct way up.
8. Move air hole to a middle setting.
9. Take some primer puffs with no power.
10. Leave standing for 5-10 mins.
11. Begin vaping gently at 6 watts - moving up slowly to 10.

Ive tried all types of juice - both high VG and high PG and in-between. Invariably at some point i start to get the gurgle. Ive tried the following fixes:

1. Using a paper towel blow gently out of the air hole to get rid of juice - doesn't work - if i kept on blowing id blow the whole tank of juice out.
2. Take the unit apart - most times there will be juice in the base unit underneath where the coil sits - dry this out - dry the coil off and repeat from step 2 above missing out steps 3 and 4. - this sometimes works but its a temporary fix.

There seems to be no pattern to the problem. Sometimes the gurgle starts as soon as ive changed the coil - sometimes its ok for a week. I have 2 units and 2 spare tanks and have rotated them all using the above method - still get the issues.

I have actually never experienced the burnt taste or reduced draw because Ive always got sick and binned the coil before that point.

I am vaping generally at 9.2 watts - but have tried as low as 7 and as high as 13 - it makes no difference.

I don't draw hard - I cannot understand why I keep getting juice in the air chamber - its not a problem with a "dud coil" unless they are all intermittently dud coils - they are all authentic aspire and I've bought them from different places - so its not a dodgy batch issue - the rings are all the correct way up - I have spent hours and hours researching to try to fix these issues - and cannot for the life of me maintain a stable nautilus mini.

Can anyone save me from madness and tell me what Im doing wrong - Im tending towards a conclusion of all nautilus mini components are junk at the moment.

Many thanks in advance  

Hey Guys,

I have been learning the ropes of RDA vaping, and so far I absolutely love it! As the title states I’m wondering what coils (FC, Aliens, etc) Would be best for flavor and vapor output? I’m currently running some Wotofo 0.33 Fused Claptons (~0.17 in dual coil) @ 60 Watts. The flavor and vapor is ok, But I’m looking for a little more. Maybe something I could run at a slightly higher wattage and get more vapor / flavor?

Any help would be greatly appreciated!

Thanks!  

Hi I have a question about nicotine strength in my juice for sub-ohm vaping: I've only started vaping my tfv12 prince smok tank 4 days ago, so total newbie- used to do only mtl before that. I'm currently using Q4 coils, 0.4 ohm, vaping at 50-60 Watts: quite happy with a cooler vape, I tried them at 70-90 but slightly too warm for me, maybe in the future it will change.
Majority of the sites and youtube videos that I came across where sub-ohm vaping was discussed said that the maximum nicotine strength used when sub-ohm vaping should be 6mg/ml. So I've mixed a few juices, 70/30 vg/pg, ranging from 3-6mg nic. I noticed that I'm chain-vaping with very little nicotine hit. But i kept nicotine cravings sattisfied with my mtl device used simultanously.
Today however, I wanted to check something. I've mixed some 65/35 VG/PG liquid for my gf's smok nord pod a few days ago, with nicotine at approx. 11.5mg/ml, so I popped it into my prince tank to try it. Expected to choke on it but no- it vapes great at 60 Watts, tastes good (carnival sherbet concentrate + a little bit of strawberry cream concentrate added) nicotine hit: I can feel it, but unless I go crazy it doesn't make me nic sick.

Is this normal? Why do people recommend going max 6mg nic for sub-ohm vaping? Is it because they aren't recent ex-smokers or they never were smokers, and just use low nic liquids at their stage of vaping? Thanks