Vaping Above 200w Help

I've been using only twin-18650 mods for some time, and before the shipping ban came into effect, I bought a backup of my most-used mod (a Geekvape Aegis X), but since the 100W single 21700 / 18650 Voopoo Drag X Plus was only $35, I also picked up one of them as another backup.

I vape exclusively on RDA's, typically with a 3mm dual coil twisted build with 24 or 26 gauge Kanthal or nichrome-80. 5 or 6 wraps with 24 gauge, 6-8 wraps with 26 gauge. I typically vape these between 90 and 110 watts.

I did not expect to get a 'true' 90-100 watts out of the Drag X, so I set a target of around 60 watts. I mounted a 3mm dual coil twisted 28 gauge build with 6 wraps, which on my Aegis X vapes great at 60 watts, and very good at 50 watts. It measures at 0.45 ohms.

But on the Drag at 60 watts, it only vapes at what feels like 30 watts on my Aegis. Setting it higher makes no difference either, it seems to 'top out' at ~30 watts regardless of the setting. 60 watts @ 0.45 ohms is only around 11 amps, so I doubt I'm hitting an amperage limit.

I am using 18650 batteries (VTC5A), and it is about time to replace them, as I am only getting around 70% the battery life as I did when new. I will be picking up some 21700 batteries at the same time, which hopefully help with things on the Voopoo.

Does anybody have any good experiences with ~60 watt builds on a Drag X Plus?  

Hi all and thanks in advance for all help.

I have

26ga + 32ga SSL
28ga + 32ga SSL

And for the life of me I can't workout how to get a coile wrapped at a decent ohms for a single coil to go in my aromamizer v2 single deck.

Can anyone help and suggest what's the best ohms to be using for single coil.

Thanks  

Ok I'm hoping I don't get heat for these questions/statements but educating ones self especially with something that is still very new is important to me.

1. Read some articles on how there is second hand vape similar to cigarettes (99% better mind you) what are your thoughts? Vaping may not be as safe as smokers think, research suggests | Society | The Guardian

2. Formaldehyde found in builds running at high watts/voltage? But 0% at low/normal builds, what i can't seem to find is whats considered to high for a Mechanical Mod or even for a V/W, V/V Setup? My normal build for a mech mod is twisted single coil 24 gauge 6-7 wraps, usually gets about 0.28 ohms and single coil 8 wraps of 24 gauge puts out 0.73 ohms on my flavor builds.
Before You Vape: High levels of Formaldehyde Hidden in E-Cigs - NBC News  

So I finally got around to putting a coil on the rba deck...my typical kayfun build, 28 ga @ 1.3-1.4 ohms. Everything looked good, coil tight....raised off the deck...screwed into the ohm meter....weirdness ensues....said 3.85 ohms...took it off, put it back on...said 4.6 ohms....looked to see if the coil screws were tight ...check. both tails tight under the screws...check. The coil deck screwed into the base...yep. No moisture in the base, nope. Put it on the ipv...said 7.7 ohms, then 4.2, then 3.90.............


Put the stock coils in the base, everything normal. Is there something I could be missing in the coil deck??? I got nothing else. No, I had not put the chimney on, so no short there. I may wrap another coil and see....I can only think that something is amiss in that little coil deck....or I am missing something in the build that is obvious. It's a really nice, tight looking coil too.  

I am trying to get the best flavor with the best single coil build.

Objectives:
Flavor Smooth Vapor
Materials:
Kanthal Wire 35mg Nic Salts
I have noticed that either depending on the diameter of the coil or the spacing of the coil wraps You get a different kind of vape hit. It seems like higher gauge wire produces a smoother hit. And then couple that with a small diameter coil build, plus squishing the coil together to remove all coil spacing results in the smoothest possible vapor.

Can anyone confirm my findings? Or does anyone have any tips because I have still to replicate the smooth hit from clearomizer sub tank cartridge's that are non mesh. I am starting to think this is because the cotton is wrapped around the outside of the coil instead of being shoelace through the middle of the coil.  

Hello so as of now I have a 100 foot roll of .26 gauge kanthol that ive been using litterally ever since i started getting into rebuildables. I have been looking for some thicker wire, and i was thinking .22 gauge but idk just wanted to hear what gauge you guys vape with!  

Hey everyone,
I've been vaping for about two years now, and have decided to start dripping. For the last few weeks, I have been dripping on an IGO-W, 26G Kanthal single coil (7 wrap micro coil reading at 0.8ohms) on my iStick 30w.

I just recently purchased a new battery that should arrive today, and was wondering if anyone had advice/tips on producing some fat clouds! Dual Coils? Different coil builds? Number of wraps? Watts to vape at? I think you get the picture lol.

The items I will be using are as follows:
-SMOK XPRO M80 Plus
-IGO-W
-26 Gauge Kanthal Wire
-Japanese Organic Cotton
- 80vg/20pg Juices

All input is greatly appreciated. Thanks!
-Tyler  

Just bought the Kangertech Subtank..... Was told I couldn't use my Max VG juice and I needed to buy some of their lower VG juice. I told the guy no thank you, I know what i'm doing and I can make it wick the Max VG.

Needless to say I got home, the STOCK OCC coil, .5 ohm, wicks my Max VG perfectly fine, even with chain vaping.

I ripped the pre-made coil out of the 1.2 ohm OCC head, and built my own .6 ohm coil in it, wicked it with Organic Cotton (Not KGD or Bacon, Just organic cotton from Walgreens) and it wicks perfectly fine with my Max VG.

I built a single coil .7 ohm spaced coil, wicked it with the double tails on each side, cut off to where it touches the deck, but not touching the threads, put the chimney cap on, and made sure the juice channel was free of blockage, and it wicks perfect with the Max VG.

No leaks, no dry hits, running each OCC head at 30 watts, and the RBA deck at 35 watts.

This is the original Subtank, 6ml for OCC and 4.2 for RBA, (NOT THE NEW 7.0mL version).

So let me hear it.... What have you guys noticed or seen about the wicking ideas, why has yours not worked?

WHY DO SO MANY PEOPLE SAY YOU CANT USE MAX VG ON RTA's, especially on the Kanger Subtank????  

Somehow, I inadvertently pushed the buttons just wrong today and it went from 7 watts (my usual power setting) to 50 watts (the highest setting). I didn't even mean to push any of those buttons.

I experienced instant burnout and a horrible taste in my mouth and the coil was instantly ruined.

Do people really vape at such high power? If so, how often do you have to replace the coil? And how many ohms are you putting that through? The coil I replaced it with is 1.77 ohms which is about the same as the one I burned out.

50 watts seems so excessive to me that I double-checked and yes, that's what it says it goes up to. Even at 7.5 watts the coils seem to burn out too fast which is why I vape at 7.

I feel like Nigel Tufnel designed this thing. "But it goes to 50. That's 43 higher than 7. So it's like 43 more. So when you're vaping at 7 watts and you want that extra push over the cliff..."

(I'm actually impressed that Nigel could do the math to figure that 50 was 43 higher than 7)  

So I decided to try a 1,6 ohm coil on kayfun v4 clone Tobecco and I am using 28gauge Kanthal with a cotton
wick on a Rdna 30 and its vaping well at 15 watts I have a kanger subtank mini coming in the mail and here goes my question
So the kanger subtank states that with a .5 ohm coil i could vape up to 30 watts but the voltage comes in at like 3.8 volts
I was under the impression that the rdna 30 needs at least 4 volts to work which kinda brings me to my second question
What is the point of of sub ohms? cant i just build a 2.0 ohm coil or something like that to achieve the results as if i was subohming
I am very confused on this
thanks for the replys in advance
Oh yea is a 1.6 ohm coil at 15 watts a normal build or any recommendations for the kayfun v4 for watts and ohms thanks again