A bit of a background, I started vaping with a disposable and eventually switched to a pod mod with the Frenzy. I liked it a lot but eventually switched to the Vapefly Jester after finding out that it has a rebuildable deck. The Jester kinda set the standard for me when it comes to how I want to vape but my only gripe with it is that the battery doesn't last and it's very hard to fine tune when it comes to the flavors that I vape. I also wanted to buy something that's more modular so I could replace the bits and pieces without having to re-purchase the whole setup should it die.
Fast forward to now and I decided to buy a Geekvape Lucid kit. It's really cheap where I live and offers a wider variety of atomizers in terms of size because it has support for 24mm diameter as opposed to the Eleaf iStick Pico 75W's 22mm. These are dated mods I know but the pool for mods and atomizers in my country aren't really as vast, albeit they can be a lot cheaper. Anyways, I decided to pair it with the Ammit MTL RDA and so far I'm liking it. The draw is perfect and the flavor is about as good if not a hair worse than my Jester. My current build on it is a 0.6 ohm Kanthal 26ga and I vape it at 20W. I vape 0mg freebase liquid with the ratio usually being 70/30 or 80/20 VG/PG depending on the flavor.
What I'm looking for is a setup that can pretty much accommodate higher VG liquids that can improve on the setup I have now while still maintaining that tight MTL draw. Typical mtl setups that I find are more geared towards higher PG ratios whereas the sub-ohm options typically have looser airflow and really wide drip-tips which I don't like.
Haven't vaped in like 8 years? So most of everything is new to me now..
But I did a little reading and I figured out a few things I need in a vape, but really there is so much, it's kinda hard to know what is good and what is not for brands and styles, so I'm hoping I can get some help by experienced vapers here.
I'm looking to quit smoking and here's what I'm looking for in a vape setup.
MTL Mouth to Lung setup so I can draw in and then inhale like a cigarette, but I would like a decent cloud. Not looking for huge, just good and maybe be able to slightly adjust what gets produced with using only 50/50 juice blends.
RTA setup? I need a rebuildable coil tank system.
I need to keep my maintenance cost low, so I need to be able to rebuild new coils.
No leak tank is a must. Needs to lay down on side on table and keep in pocket.
1 battery or 2. Doesn't matter much.
Would like a smaller mouthpiece compared to the larger style so I can get a good MTL draw.
Not sure what my options are for tanks and box mods or pen style? I think I need some kind of box mod? So i can slightly fine tune watts, volts to my coils if it just doesn't feel right and needs minor adjustments? Also like the option showing how many seconds used or draws.
There's so many tanks out there, but it's hard to tell what is really good.
The battery side, I really have no idea what I would need... watts, ohms, voltage.. with all the combinations, I can figure out what I really need..
Not looking to just be easy simple. I want good quality and I can only buy once.. I can't really afford it as it is, but I need to stop smoking..
But I want to buy once and be good for long time and not wish I bought something else. I just don't have the money to play around like that..
So I hope I can get some help here or suggestions to get me looking in the right direction for tank and battery side system.
Quality brands?
Brands to pass on because there is better options?
I make the choice that I'm certain I'll be vaping forever. I figured since I enjoy it, I'm gonna learn everything I want to know and make it a hobby.
Me being a perfectionist, I decided it was time to piece together a setup that was not only powerful, but pleasing to the eyes.
After much consideration, I made the choice to not go sub ohm. I instead decided a higher power, higher ohm setup would please me.
So this is what I ended up with.
Aspire CF VV 1600MAH battery. Instead of rocking a VV+ most people use, I went the route I did to get 600 more MAH battery and didn't care about the beauty ring because after all, my Aspire K1 tank is a backup now and can't be used with the VV+
The tank had to be good too. This was where I wanted to upgrade the most. I wanted adjustable airflow, and better coils.
The Nautilus Mini was the only clear choice. 2ml is fine for me as I switch flavors now and then, and the new redesigned OCC coils you can purchase was a selling point.
I've been using the setup since last night, and WOW!!! This tank brings the flavor through in ways I never thought possible. Also, the vapor production is amazing to me. I don't care about cloud chasing so by my standards this is a fog machine at higher voltage lol.
Overall with 5 additional spare coils I'm about 65$ in this setup and that's a bargain. It performs so well.
Also wanna throw out that GWAR Spew from MBV is friggin amazing in this tank!!!!
Hi forum,
I've been a smoker for 25 yrs. 2-3 PPD of lights. 7 yrs ago I started to vape and was able to cut back to 10 analogs a day. I used KR808 with cartos and then upgraded to Ego's with cartos and later tank atomizers. Dripping was never my game. A year and a half later, I stopped vaping and went back to cigs. Why? I got tired of charging, filling, leakage, dry burnt hits, modding ...etc. And I was not getting the satisfaction I needed.
A couple of weeks ago, I thought why not give it another try. So I got my boxes of eliquid and batteries out of the closet. I was surprised that all my Egos were still working (the KR808's are all dead). What's more surprising is that the eliquid is still good after 5 or 6 yrs. The flavor is still as good as it was. And the nicotine is still there. The TH, peppery taste and the buzz are still the same. So here I am, vaping again and I already cut back my cigs use to 10-15 per day.
I wanted to check the ecig world of today. And what's better than ECF. I've been at ECF for 6-10 hrs daily for a week now. And omg what a change!! VV, VW, TC, tanks, rebuildables, Subohms, NET, WTA, mods, mods and even more mods. Amazing! Hats off to the ECF family. I don't think all these advances would've been possible without ECF. Ideas are born here.
With all these advances I'm hoping that I'll be able to quit cigs completely. But it's really confusing and I need advice from the veterans here. As to my vaping style, I inhale M2L, use 70/30 to 40/60 pg/VG most of time. I chain vape !! 24 mg is the least that works for me. 36 mg is better. I like a warm (not hot) vape. I need a good balance of vapor and flavor. I'm not into mechs, rebuildables, dripping or modding. I like hassle free setups. fill, plug and vape away.
I want 2 setups. One for work and stealth vaping. Should be smallish (Ego size), does not look ridiculous, consistant and easy to use. box is ok but should be small. It should still have options that will enhance the experience. The second setup is for use at home. maybe a high end VV VW with TC. Damn! that Sx mini looks great. /But i'll wait before throwing away $200.
Sorry for the long post. But what suggestions and tips can you give for these 2 setups?
TIA
I bought the MVP 2.0 Starter kit from Mt. Baker. I like the tank it comes with, but I feel like using a drip fits me better. I started with a eGo like everyone else and recently moved to this Box mod when I saw it for so cheap on baker.
I want a drip setup because I don't vape all the time, but when I do, I like to control how much I vape so I don't binge on juice.
Any setups for "Drip"
Prefer to keep it nice and cheap, as a college student, money is a big problem.
Hey everyone, I just wanted to post my setup here, nothing to fancy so just take a quick look and feel free to leave a comment or reply.
To kick things off I've got a Seeker Mech Mod by EHPRO. It's a sleek design, all copper, and easy to press button. Little short and thick for those of us who like our setups to look beefy.
Atty- The Tobh Atty. It is a pain in the butt to take apart from the get go but once you get a bit of juice on all the O rings it comes apart fairly easy. Good deck to build on all pre-drilled holes on the three posts 1(+) and 2(-) (Obviously). Deep basin to hold plenty of juice for our drip and drivers safety. My current build is a dual single coil coming in at 0.28 ohms. Using a regular cotton wick.
Juice- "Bliss" made by The Artisan Vapor 100%VG This juice is an explosive flavor of fruits, and for being 100%VG it has a heavy flavor. 39ml bottle runs at 20$ not to bad for a good juice. When I drip with a full basin it lasts roughly an hour, and I heavily use my vape.
Battery- This thing is one of the best right now but I'm still limited on what builds I can do. My 0.28 is safe, however my 0.22 is unsafe (Go figure) ANYWAYS! (Specs) MNKE IMR-26650 3.7(low) 4.2(High) 3500mAh.
So I think that's all. Thanks for reading guess, and questions or comments just drop it down below. Goodbye and VAPE ON!
Greetings,
maybe I was bored. Maybe to much doom and gloom on all the bans of new gear and the shipping of it. I started to think - why not have some fun with some of the stuff I already have?
Cases in point - the two rigs in the picture above. I believe that all the hardware (mods and tanks) are over 5 years old. The setup on the left has a bit of a story about it.
Sitting on my desk is a few old tube mods that I wonder what it would be like to use again. I found a old (I think KFv3) tank laying around, built a very low mass 2ohm coil in it, filled it up and went and tried it out on my old 15W tube mods. Sadly not a one of them liked the KFv3 and would register the 2ohm coil. So what to do? I had a old Evic that surely could be put into power mode. While I was not to surprised that it all works (I've actually refilled the tank a few times and replaced the battery once) the vape is more restrictive than I tend to like and be it the build (or the 10W power mode) I don't really like the flavor of the unflavored juice with this. Another negative is that while it is top fill, there is no juice flow control so the atomizer get flooded each time the tank is refilled. While I could (and have) used it in a pinch, I can get 1-2 tank fills on a single 3000mah battery.
The setup on the right represents some historical firsts for me. Years ago when I first got into rebuilding a Lemo2 was one of three tanks I bought when I started. It was also my first top fill tank. Sitting under it is my first ever Dicodes mod (a #6). This mod is setup in TC mode with 380F temperature setting and 23W.
Be it the better tank or the use of TC mode, the setup on the right provides a good vape. The 26650 has enough mah to easily allow me to vape the tank dry (takes me most of the day) and since years ago I got Dicodes very over priced charger, I just drop the mod in the charger at the end of the day and its ready for more vaping in a few hours.
So, anyone else putting to use or having some fun with +5 year old vaping gear? How do you like it?
g.
First off, I would like to say that I’m very new to vaping. I started off with a JUUL, then a Smok Novo 2, and eventually got sick of buying pods.
Now I have a Hellvape MD, and an Ares 2 - the first provides better flavor, but it’s still not comparable to what I was getting in my pod systems. I just recently purchased a BP Mods Pioneer, and I’m hoping that gives me better results. I’m using an Aegis Mini for a mod.
I’m trying to figure out what I’m doing wrong, because it’s really frustrating to spend all this money for worse flavor, when I was hoping it would let me save money.
I have about 40 bottles of salt nic flavors that are 50 or 35 mg, and a couple 3mg freebase I bought (120ml for $7 seemed like a steal). I would really like to get away from the salt nic, but I seem to get even worse flavor from the 3mg.
I’m using 2.5ID 28ga SS316L round wire from Master Wire Supply (I have a spool) with Puffs Organic Cotton. My coils are usually .7ohms, but I’ve tried up to 1ohm. I’ve also tried 1 ohm Vandy Vape Superfine MTL fused claptons, and experienced similar results.
I’m using the MD with the most restrictive airflow settings (3 small hole airflow disk), low (2-3) adjustable AFC setting. I have my coil as low as possible to the airflow, and I have thinned / fluffed my wicks.
I haven’t tried adjusting the airflow below the coil on the Ares 2, because the video instructions say wide open airflow below the coil is the best for flavor (I have found the opposite to be true for the MD).
Can someone provide me more insight?
Will 2mm ID coils with the same amount of wraps taste better than 2.5? Do coil ohms do anything for flavor, or does it only change how fast it heats up? Will I lose flavor if my coils hang outside the diameter of the airflow disk?
Is there a certain type of coil that would give me better flavor than regular round wire?
I use TC at 420F 20 watts
Any kind of feedback is appreciated and if I left anything out or you have questions about my set up that could help me out please ask! I’m at a loss on what to do, and it seems like no amount of research is helping
Greetings to all
Having quit cigs, I am alternating With Jf Minifit*20mg Nicsalt for outside and nic craving, and Aspire K4*3mg regNic at home, because as it leaks and, at just over 12cm, too big, annoying for pocket. K4 is great to vape and at length with low nic, since I do sometimes just need to keep puffing, and I am worried about how much I use the minifit with the 20.
I am hoping y'all'll be able to advise and help. The following is a rather stretched permutation of a similar thread (with older gear and less details):
Will the Aspire Nautilus fit the iStick Pico?
Looking now to have something with the (1)dual function, to gradually lower the nicotine while shifting the settings to keep things cofortable and satisfying. In other words, I am seeking to have something that can do both 20mg Nicsalt and Subohm.
(2)Size (averse to large devices) and (2)leakage are priorities. So is (4)ease of filling and coil replacement. In addition, if possible, I would like to exclusively (5?)keep with salts (even as I lower the nic).
The boys at the store recommended istick pico + nautilus 2s. Does this setup work for the numbered and underlined above? Do the pieces fit? If so, can I use the sub-ohm coil for low nicsalt or is the material of the salt just bad for sub-ohm regardless of nic level?
Which is easier to fill/change coil: nautilus 2s standard or TPD? ANy other differences? Is the TPD available in Europe?
Is nautilus the only tank with the dual function?
Is it worth having two tanks to be able to keep shifting? Whether Nautilus 2s or another? And is there some sort of bag or case for my stuff to keep in my backpack (saw a lady with something for her stick in her purse once)?
Given the purpose of ease, Should I consider the Orion Lost vape, or is the ability to lower the wattage just not enough, and I need something with high-ohm. Keeping in mind I don't like anything higher than 3mg on the Aspire K4.
What about Chubby Bunny and Magico? Easy alterntives that vape better than Minifit, have a little more options but not too complicated and still easy to use, fill, etc?
I noticed, pico is small, together with 2s they'll be bigger than K4. Given the purpose of size, what about the istick pico baby + nautilus mini? Do the sizes fit and can nautilus mini take high/sub-ohm coils?
Is nautilus mini easy to fill like 2s or is it like the old nautilus requiring cap removal?
On their website, I read that nautilus mini has 2ml capacity and standard/tpd 2.6, but in the thread above it said the standard has 5ml. Who's correct?
Why didn't the boy recommend other setups? I came across istick pico X and Snowwolf mini and what about Aspire own mods like the one that comes with nautilus; the Zelos, K1 Stealth or Reax Mini?
Finally, is there antyhing I should know about VG/PG percentages with Salts and any of the devices above?
Thanks in advance!
I've had the same exact set up for about a year and a half now. Itaste VTR + Aerotank with 1.5 ohm coils, and i vape at 9.0 watts. I tend to only vape one specific brand/flavor, I'm one of those weird people that just like one thing and stick with it. Up until July last year, i used a local vape shop's liquid. I liked it and it was fantastic. I'm a little fuzzy on their ratio, but I believe it was 70/30 pg/vg. Their liquid would never pool under the coil and my coils would last for over 5 weeks at a time. Then i moved. The cost of their liquid plus shipping was just too high, i was already paying 22 bucks for a 30 ml plus shipping on top of it was just killing my wallet. I found a couple other sources of liquid, one on the net being Apollo ecigs, and the other being local B&M selling VGOD liquid. Both of those i believe are 70/30 vg/pg.
Now since the switch to either of those 2 liquids, my coils are only lasting 5 days tops, and at nearly 2 dollars a pop, its killing my wallet even more than with the liquid i was having shipped here from that local store in FL. What is going on? Is that ratio of VG/PG killing my coils? Its not so much that the coils are burning out, but i just keep having to take a harder and harder draw as the days go on. When its a fresh coil, i get tons of flavor and good vapor, but towards day 4-5, flavor minimizes and vapor decreases. I've soaked them in distilled water and let them dry out, but even that the flavor/vapor tends to peter out after a day or so.
Thoughts?
I was talking in another thread, and the question came up that may be a good topic... for the experienced vapers, if you had to recommend one vaping setup... both atomizer and battery.... what would you recommend to someone who had.. say.. a pack and a half per day habit? I am curious as to what you would recommend to get someone to stop smoking, and it be an "end-game" product.....one they wouldn't need upgrading later. Both atomizer and device.
And yes, I know some people may turn it into a hobby like me and want to buy a variety, but I am strictly speaking for the stopping smoking part.
I'll go first...
I'd recommend an Istick 30 with a subtank mini. I think that atomizer and battery combo offers a convenient size, good juice capacity, reliable, a wide variety of vaping options, and just a good "grab and go" setup.