It's an Innokin Endura T18 II. I bought it just a week ago. Everything was working fine until this morning when I tried to fire it and it just blinked three times. I thought maybe there was a problem with the coil, so I put a new one in. It was still blinking. So I made extra sure the coil was in properly. Then it started working again. I vaped for about an hour and then it started blinking again and wouldn't fire. Any idea what the problem is?
Well this sucks, I have an iStick 30w and toptank mini, I ran out of pre made coils so I thought i would try the RBA of the toptank. At first it read out as “protection” upon trying to fire it (I think the ohms were too low on the pre made coils included with the RBA at .1), then it said low battery (it was almost fully charged) so i plugged it in and tried to fire it once more and the thing started smoking (no protection message this time, just a little puff of smoke within the LED window). I only fired the button for a split second and it still seems to be functioning. Not sure what I should do lol or just ditch out on it? It appears to be working yet but stinks like an electrical fire now. I’m kinda reluctant to use it (I still have an old coil but it was starting to taste funky). Any advice or idea what might’ve happened?
I bought two Innokin Endura M18's, and both seem to have problems.
The lights have gone out. There is no way to know the battery power, when they are fully charged, etc.
And now both of them don't seem to vape very well, like there is a air leak. I am using the Innokin M18 tank/coils with them.
Does anyone else use the and how has your experience been with them?
I was vaping on my subtank mini on top of a cana clone and it was working fine until the screen started glitching. It would only show like half the screen or the screen would be all jumbled up and it wouldn't fix until I turned it on and off a couple times. I took out the battery and let it sit overnight and when I popped in a new battery today the screen isn't lighting up at all, also its firing a lot weaker, and randomly locking itself. What can I do?
One of you guys suggested the Voopoo drag x when I discussed my 20th vape device no longer charging through the USB mini. It was a Geekvape which they claim are indestructible. Of course they don't mention how the USB port is a cheap piece of garbage that will eventually fail even when treated delicately. I received the Voopoo drag x in the mail a couple days ago. I didn't realize it doesn't come with a battery so I picked up an IR18650-25R 20A 3.7V battery at a local vape shop. It was working beautifully for about a half hour and then it would just turn off. Even if I pushed the buttons or clicked five times, it wouldn't power up unless I took out the battery, put it back in and then clicked five times. Then I would get a few puffs and it would turn off again. Then today, I started receiving a message that said "atomizer short". I kept getting this message over and over even if I took out the coil and put it back in. Occasionally, it would start working again, but between the device powering off and the atomizer short problem, it's more or less unusable. It was only about $60 in total so no biggie. So now I'm shopping around for my 22nd vape device. Does anyone have any suggestions?
So ran into another problem with my itaste 134, it was working fine a few hours ago. I went to refill my tank and when I put it back on it wouldn't fire, I looked at it and noticed when ever I pressed the bottom the light would instantly turn on then stay lit for 5 second. But no vapor at all. It now does this with or without a tank on it. Any idea what this could be?
Hey guys.. i been vaping for a while and not had this hapen before.. i am using a Hugo Vapor Rader and ot has been working with no problems until today... when i go to use it, when i try to fire, it says high atomizer the first time i push fire button followed by low battery (have tried multiple sets) when i press again. If i persevere and keep attempting to fire it works fine as if there were no problem until the next time i go to use the device when the process repeats.. i have taken the tank apart and cleaned and put back but the issue continues.. anyone have any ideas on what is wrong/what i should do?
Hello, so I have an innokin gladius and the wick is burnt and I think that the wick and the coil are in one piece, but the problem is I cant get to a store for a few days so im wondering if there is a way to clean it, if you could please either explain it or direct me somewhere it says how that'd be great thanks
Hey guys what's up?! I just bought the Innokin Kroma R mod with the Ajax tank and I was wondering what other DTL tanks I could buy that would properly fit the mod. The Ajax tank is 24mm so I'm looking for something similar that has great flavor and longevity when it comes to coil life. Please help me out guys!
Thanks,
Brian
I stopped smoking, and started vaping 2 years & 2 months ago
My magical device was an Innokin Endura T18 vape pen, followed by the Innokin t22 kit
I would love to hear what other members used to stop smoking
okay so i hope i'm posting this in the right place, but i have a nautilus mini that i've had since december and i just bought a new coil for it yesterday from my trusted local vape shop and it was working okay at first, but then it started gurgling and spitting juice into my mouth
this isn't the first time it's done this, i actually stopped using it for a while because of this problem (and the coils were old, so i thought that's what was causing it) but i just put a new coil in and it's still happening...
i have scoured the internet for reasons why this might be happening and i've tried every trick in the book and nothing has worked
PLEASE HELP!