Problem With Device

I got a problem with my Luxotic Surface. I'm using a LG Choco Battery 18650, it was fully charged and when I press the fire button suddenly it appears for Battery Low even the battery was on fully charged. I tried my spare battery maybe its just a mistake putting a fully charge battery, but it was the same issue also with the spare battery. I tried the 2 batteries with my Geek Vape Aegis 100W to check whether my batteries are already broke but it works fine. I was vaping for my Luxotic Surface by 55.0 Wattage, 0.21 ohms, 3.40 Voltage. Can someone help me out to fix this problem?  

I've got a couple of these little mods and both have the same problem. They continue to fire after the button is released. When it happens the display changes to the power on/off and keeps firing until the unit restarts (presumably after the 15 second cut off?). I can only think that the mod is registering 3 presses when I fire which triggers the screen change, and there is a bug which stops the release of the fire button registering. Anyone experienced this? Any fix? I'm surprised it's happening with two units so it must be happening to someone else!  

I've been using my Atlantis on a Kamry K101, and just got hold of a Kbox because I wanted to boost power. Unfortunately, the Atlantis won't fire on the Kbox. Charge indicator shows battery full charge, but it won't fire on any wattage selection.

The Atlantis I'm using fires fine on other batteries I've tried, and the Kbox fires an iClear 30S with no problem - it just seems the Atlantis/Kbox combo doesn't want to work together. The contacts on tank/battery are clean, no gunk or liquid in them.

I've tried Googling the issue, but all I'm mainly finding is people recommending the two together as a good combo.

Does anyone have any idea what could be causing the problem?

Thanks in advance for any help.  

Right now I have a few box mods, the IPv3, SIG 150w and the Snow wolf 200w. I'm using the Snow wolf 200w and honestly I'm not happy with it. I've had the button stick a few times causing it to auto fire and I'm noticing an almost one second delay from when I hit the fire button to when an actual vape starts to kick in (very slow fire up time, and I'm only running dual twisted 26g) on top of that I really dislike that I have to hit the fire button to see how much volts I'm using. I know the SX M class is one of the best out right now, but the fact it's a single battery concerns me because I typically vape between .12-.20 ohms and usually 60-80w (but since getting the derringer it's been 60). I really like the hot, dense flavorful vapes and I wanna make sure if I get the SX M class it'll be able to deliver that.  

So ran into another problem with my itaste 134, it was working fine a few hours ago. I went to refill my tank and when I put it back on it wouldn't fire, I looked at it and noticed when ever I pressed the bottom the light would instantly turn on then stay lit for 5 second. But no vapor at all. It now does this with or without a tank on it. Any idea what this could be?  

Hey everyone. I've noticed that just about every day since I've used it. When I hit the button to fire it, it will fire for a couple secons then stop, and then fires back up again. And it's starting to concern me. Does anyone else have this issue? And how would I go about fixing it?  

I have had a lot of mis fires on my Smokless Owl 25.00 squonker and had to press down extra hard

and sometimes side ways to get it to fire.

I just done some contact cleaning and scraping on the Smokless Owl Button.

I took my wifes Emory board finger nail file thingy and depressed the firing button and held it depressed and rubbed it

across the firing pin and then took a small jewlers screwdriver and scratched it back and forth across the end of the pin and

did the same thing to botton ground pin.

I noticed some black color on the end of the firing pin before I started this cleaning process.

I gently took the screw driver and scratched back and forth across the positive and negative end of the battery just to

take any small film or oxidation from the ends just to make a better connection.

It seems to fire now just like it should with no MISFIRES---mod is now perfect !  

Well this sucks, I have an iStick 30w and toptank mini, I ran out of pre made coils so I thought i would try the RBA of the toptank. At first it read out as “protection” upon trying to fire it (I think the ohms were too low on the pre made coils included with the RBA at .1), then it said low battery (it was almost fully charged) so i plugged it in and tried to fire it once more and the thing started smoking (no protection message this time, just a little puff of smoke within the LED window). I only fired the button for a split second and it still seems to be functioning. Not sure what I should do lol or just ditch out on it? It appears to be working yet but stinks like an electrical fire now. I’m kinda reluctant to use it (I still have an old coil but it was starting to taste funky). Any advice or idea what might’ve happened?  

One of you guys suggested the Voopoo drag x when I discussed my 20th vape device no longer charging through the USB mini. It was a Geekvape which they claim are indestructible. Of course they don't mention how the USB port is a cheap piece of garbage that will eventually fail even when treated delicately. I received the Voopoo drag x in the mail a couple days ago. I didn't realize it doesn't come with a battery so I picked up an IR18650-25R 20A 3.7V battery at a local vape shop. It was working beautifully for about a half hour and then it would just turn off. Even if I pushed the buttons or clicked five times, it wouldn't power up unless I took out the battery, put it back in and then clicked five times. Then I would get a few puffs and it would turn off again. Then today, I started receiving a message that said "atomizer short". I kept getting this message over and over even if I took out the coil and put it back in. Occasionally, it would start working again, but between the device powering off and the atomizer short problem, it's more or less unusable. It was only about $60 in total so no biggie. So now I'm shopping around for my 22nd vape device. Does anyone have any suggestions?  

Hello very basic question I love dripping and do it all day my one problem is with the mech mods I have I cannot place them down with out locking them or they fire sometimes anyone know of a good clone that will not fire when placed down maybe one with a recessed button of sort?

I currently have a F U and a Stingray infinity