Can Someone Help Me With Wattage Calculation?

I’m a mouth to lung vapor and currently using the holic rda and galaxies rdta. I’ve tried using ni80 round wire and superfine mtl fused Clapton ni80 wire. The round wire is so easy to work with and the superfine is harder but I’m getting the hang of it. My question is with coils that ohm out the same with each wire I get flat flavor with the round wire and the flavor definitely pops with the fused Clapton wire. Is this normal? Same juice, same wattage, same ohms and same rda and squonk.
I love working with the round wire but not worth it if I can’t get better flavor.  

I recently got a VOOPOO mini. Came with a small low wattage coil installed already. Used that one and got great flavor. Just went thru 2 N1 coils. Terrible burn and horrible flavor. I let both coils prime for over 15 minutes and set at low wattage to begin with. I am very unhappy with these coils so far.  

Hey Guys,

I have been learning the ropes of RDA vaping, and so far I absolutely love it! As the title states I’m wondering what coils (FC, Aliens, etc) Would be best for flavor and vapor output? I’m currently running some Wotofo 0.33 Fused Claptons (~0.17 in dual coil) @ 60 Watts. The flavor and vapor is ok, But I’m looking for a little more. Maybe something I could run at a slightly higher wattage and get more vapor / flavor?

Any help would be greatly appreciated!

Thanks!  

Hello—am I calculating correctly? I now have a Jackaroo mod that takes a 21700 so I ordered the Molicel 21700 P42A. Someone on the forum helped me out once before and here is the calculation I used. I figured in at 30 watts –I am usually between 23 and 30 watts

30 watts/3.2 battery cut-off voltage/.9 - 90% efficiency = 10.4 Amps
(30)(3.2)(.9) ---max wattage to be used is 86.4

What about my 2 battery mod --is that calculation for each battery. For example, I ordered a Geekvape Aegis X that takes 2 batteries so If I had that same calculation would my wattage be 86.4 per battery?  

Where can I buy just the Clapton coils or wire for my SmokeTech Cloud Beast. I’ve been using the rebuildable coil for 2 years and it’s always been at .3 ohms. Over the last week it has slowly gone up to .52 so I took it apart and saw that the putter wire is degrading.

They are Clapton, correct? Or fused Clapton?  

So I've been building my own coils for a short period of time and I'm looking to better understand how my coils can affect my vaping experience, specifically varying ohms and wattage's.

I've been building mainly only one coil as I'm still trying to better understand the basics of coils and more importantly wicking. Ofc all I hear these days is how sub ohming is the best and with all the sub ohm devices I feel like I may be missing out on something if I'm not at .5 or below.

The coil I've been wrapping is a 28g .9 ohm single coil. If I were to go lower, how does this affect my vape on a regulated device? Unless I'm missing something, only the heat flux and quickness to heat would be affected right by lower resistance (given a set wattage)?  

Hey everyone. I've using Aspire non Nautilus Non Atlantis BVC coils. 1.6 ohm. Volt rating shown on coil is 3.0-4.2v. Aspire says anything under 15w is good. Well did calculating and up to 4.8v would fit that wattage.
Help?  

I have a dna75 single 18650 that I take out with me.
I just ordered a bunch of small'ish MTL clones to use with it (Spica, Prime, V5, Millie, Gate).

I also have a DNA250C triple 18650 that I use at home.

I never used TC and don't really want to learn it nor power curves but might have to learn that later if I feel the need to. I already prefer and am grateful for escribe customization so maybe TC and curves won't be a PITA to add.

I couldn't get DNA250C's idiot-proof Replay Mode to work the one time I tried it with a dual SS fused clapton (others have had this problem, maybe it was the tank I was using).

For DNA250C bigger builds, I just ordered an Aromamizer V2 Plus RTA. And a Fatality 25mm. Fatality I might also use on the DNA75 with a smaller coil so battery easily lasts a day.


I'm guessing for the smaller MTL tanks to get round 316L if I do TC, and for wattage mode some Kanthal. I'm OK with even buying a DNA75C for Replay mode if the MOD is small sized though.

I really don't like ramp up time even with smaller coils, so maybe I should just learn TC and get 316L wire? For the DNA250C builds, ramp up would be long but I'm hoping Replay Mode will easily solve that.

Not sure which gauges.

And/or maybe for the MTL smaller builds get some thin clapton or something besides round? I don't want to kill the battery fast though but am OK with smaller puffs.


I already have some all-SS 316L Geek Vape Fused Clapton 26ga * 2 + 30ga, so that should be good for the bigger builds and Replay.



Thank you  

Hello guys,
I recently purchased a single coil RTA, my first rebuildable experience. I love it!! .
I saw at the shop a double coil RTA and a Double coil RDA, was planning on buying one of them until I thought I only have a 100W mod. Do you guys think it is enough? Are there some specific ohms coils that could make it work etc? Or is a 100W enough? I am new to this so calculating ohms law and all the other stuff I will learn, I just need a answer from the double coilers if you guys use higher wattage mods or not.
Thank you in advance!  

I have a TM 24 pro. I threw In a pair of Juggernauts just for astetic reasones.
I also have the geekvape mesh pro atty. With some, (most) juices I get a better flavor from from the mesh pro. With the TM24 pro and the Juggernauts I obviously get significant more vape. But my tank atty gives me more flavor. I fear pushing the 24 pro with the Juggernauts past 120-130w just because of the batteries i current have. Is it just the Juggernauts giving me the lower flavor or what? I have other coils, the alian, interlock alian, and the staggered fused Clapton. Is it the coil, our just the cloud chucking RDA o have.