Mech Mod Coil Build

Hey forum folks. I got lucky enough to win beyond vape's monthly prize and chose the neptune V1 hybrid mech mod. It will be making its way to me soon but in the mean time I need to get all the various goodies to make use of it. I need some recommendations for battery, battery charger, and dual coil build for the 3post rda that is built into it as this is my first rda and mech mod.

Thanks in advance  

Well , I aint even gonna say much this thing is better than any mech mod out there . You guys told me to start building higher ohm coils and i did , I build a 2.3 ohm coil . My 2*18650 box mod performed like .... with it , I had to hold the button for 2 - 4 secconds before draw and i still got minimal vapor . So i got the istick 50w , i set it to just half of its full potention , 25W and it is firing up the 2.3 ohm coil as soon as I press the button and I am getting extreme vapor production . Also size i knew it will be small , but i can not believe how small it actually is , absolutely amazing , build quality is also amazing . I should have moved from mech mods to VW a long time ago .  

hi all i have created a build dual coil with 27gauge wire 5 wraps, i dont have an ohm reader to read the ressistance , and i want to put it in a single 18650 mech mode. Do you think its ok to do it like that ?  

So I built a twisted build out of nichrome 60 wire and tried it on a triple series 18650 mechanical box and it melted the coils why won't nichrome work with any series boxes 8.4 volt melted 12.6 volt melted but I can build a .06 nichrome build and run it on my mech tube mod and it handles it I can build .15 and run it at 150 watts on my Sigelei and it handles it but bump up the voltage and it melts don't get it. I ran a .30 nichrome build at 260 watts on a SMY 260 and had no failure of the coil so I'm puzzled why a series mech box desemates the coils?  

Just finished up my first build using 24 Guage kanthal with 9 wraps. It's a dual coil build that came out to .49 ohms. It's not the best looking build but for my first attempt I guess it's not too shabby. It was built on my mutation x v4. 40-45w was about as high as I could go before it got too hot for my liking. just wanted to share it.  

It's often been said to test a new coil build on a regulated mod before using it in a mech mod. Just for fun, I tested a new build on multiple platforms to see how consistent they a

These are AVS stainless steel premade quad core clapton 30x4/40 3.5 7/6
Two coils in a Dead Rabbit V2 RDA

Coil Master Tester 0.17
Uwell Crown mod 0.19
Wismec mod 0.18
Geek Vape Aegis 0.18
Vapresso Luxe 0.18

Closer than I would have thought!

Incidentally, the old coils were in there for 8 months, although this unit is in rotation, so maybe a months worth of actual use.

Also, the top cap was just about impossible to remove from the tube. I had to insert a chap stick into it and slam it on the desk for it to come off.  

I recently picked up an infinite origen v2, my first build was single coil 2.4mm and it was not good on flavor, next build was dual coil 2.4mm at .5ohms, it was better on flavor. No matter what single coil build I try the flavor is just not there. Any suggestions on great flavor builds???  

An online vape shop here at Greece at the description for dotBox Dual Mech mod says"

"Switch to Parallel Mode for longer Vaping time and exceptional power from two 18650 batteries".

The dotbox dual mech has the option to select series or parallel connection via a switch.
I send them a email that this doesn't apply (for the same power output always),for example 0.1 ohm coil in parallel connection and 0.4 ohm coil in series connection.

Two batteries in series provide the same amount of watt hours a parallel connection does.

The vapeshop replied and told me that the description is copy and paste from Dotmod.com

Indeed.
QUOTE from dotBox Dual Mech - dotmodretail
"Last Longer. Switch to Parallel Mode for longer Vaping time and exceptional power from two 18650 batteries".

The vape shop also said that the voltage sag at parallel connection is spread out over the two batteries in Parallel.Thus more vaping time than using a series connection.

Okey I made the calculations for voltage sag using for example two Sony VTC5A 18650 batteries with a DC Internal Resistance = 18.6mOhms (0.018 ohm).

I got the same voltage sag 0.378 V in both configurations (0.1 build in parallel-0.4 build in series).

Am i correct or am I missing something?(i'll send to the vape shop the link for this thread so they can read your opinions because i think they believe i'm talking bulls..t!  

I have a hades 26650 mechanical mod and I was running a tobh atty v2 dual vertical coil build. It was working perfect but I was getting tired of dripping. I bought an aspire Atlantis, and it won't fire. I feel as though it's my mod, because I was fumbling with some adjustments on it, and it fired for about seconds. I was very happy with the production and flavor. But, now no matter what I adjust or anything, it won't fire anymore. I cleaned the connections and everything. Please help!  

over the past month or so i have gradually moved into RDAs as opposed to RTAs/Cartos. most of my builds typically come out anywhere between .24-.45 ohm, dual coils. i bounce back and forth between my SMPL mech mod and my ipv mini II.

on the ipv mini II i'll take anywhere between 4-8 pulls between 30-50 watts when i get a "too hot!" message on the display. this has happened to me about 8-10 times already over the past two weeks or so. has anyone else with this device, or one similar, have this happen before?

on the SMPL mech mod i notice the top of the mod and the atty getting hot pretty darn quick when i have something like a .34/.37 ohm build on it. once it gets hot like that i just stop because obviously i don't want it to blow up in my face.

i only use 24-28gKA1 as of right since its all i have. i'm waiting on a shipment of some n80 though, hear some good things about that wire.

being 100% honest i am looking for the bigger clouds with good flavor. i did some searching around on here and found some decent stuff that is helping me figure everything out.

anyone got any ideas on the routes i should take to avoid this over heating and being able to get good dense clouds?

edit: i use sony vtc4's and vappower 2500mah 35amp batteries which i bought from vapehappy.