Help With Coil Wrapping

so in my pursuit of vaping above 200 Watts I made a fuse 3x24ga gauge wrapped with 36 gauge and I tried three coils. it came out .07 I Vaped it at about 375 watts it was a hot vape but the ohms were very low so I had a problem with power my DNA 250c was reporting 65 amp output so I took that and put in dual fuse 22ga gauge wrapped with 36 gauge I ran that build triple coil I used it at about 250 Watts. what I am trying to do is vape at about 300 to 400 watts with an ohm or .2 to .3. the inner diameter will be 5.5 or 5 mm I'll be using the kanthal core wrapped with 36 gauge and ni80.I'm trying to figure out what my next bill should be to try to vape above 300 watts the restrictions I have is it can't be below point 1 ohm or above .3 ohm I have two aromamizer plus has with the series deck The parallel deck a second parallel deck and a single coil deck. The single coil deck fit 6.36 mm.

I also have the aromamizer titan.

What gauge would you Clapton?

Sent from my HD1907 using Tapatalk  

So I finally got around to putting a coil on the rba deck...my typical kayfun build, 28 ga @ 1.3-1.4 ohms. Everything looked good, coil tight....raised off the deck...screwed into the ohm meter....weirdness ensues....said 3.85 ohms...took it off, put it back on...said 4.6 ohms....looked to see if the coil screws were tight ...check. both tails tight under the screws...check. The coil deck screwed into the base...yep. No moisture in the base, nope. Put it on the ipv...said 7.7 ohms, then 4.2, then 3.90.............


Put the stock coils in the base, everything normal. Is there something I could be missing in the coil deck??? I got nothing else. No, I had not put the chimney on, so no short there. I may wrap another coil and see....I can only think that something is amiss in that little coil deck....or I am missing something in the build that is obvious. It's a really nice, tight looking coil too.  

Hello guys,
I recently purchased a single coil RTA, my first rebuildable experience. I love it!! .
I saw at the shop a double coil RTA and a Double coil RDA, was planning on buying one of them until I thought I only have a 100W mod. Do you guys think it is enough? Are there some specific ohms coils that could make it work etc? Or is a 100W enough? I am new to this so calculating ohms law and all the other stuff I will learn, I just need a answer from the double coilers if you guys use higher wattage mods or not.
Thank you in advance!  

Hello.
So I think i kind like a cooler vape been getting some heavy lung feeling lately been vaping a 1.2 ohm single coil 28 g kanthal
cotton wick on kayfun clone v4 Tobecco, i would like to try like maybe 1.8 or a 2.0 ohm coil or is the kayfun v4 really better for
lower ohm coils I keep reading where the kayfuns sweet spot is like 1.2 - 1.5 i did lower my wattage from 14 to 12 but i like to seem some clouds more of a flavor chaser than a cloud person though
so i am just wondering if anyone has tried a kayfun around 2.0 ohms and what the vape was like
thank you  

Ok I'm hoping I don't get heat for these questions/statements but educating ones self especially with something that is still very new is important to me.

1. Read some articles on how there is second hand vape similar to cigarettes (99% better mind you) what are your thoughts? Vaping may not be as safe as smokers think, research suggests | Society | The Guardian

2. Formaldehyde found in builds running at high watts/voltage? But 0% at low/normal builds, what i can't seem to find is whats considered to high for a Mechanical Mod or even for a V/W, V/V Setup? My normal build for a mech mod is twisted single coil 24 gauge 6-7 wraps, usually gets about 0.28 ohms and single coil 8 wraps of 24 gauge puts out 0.73 ohms on my flavor builds.
Before You Vape: High levels of Formaldehyde Hidden in E-Cigs - NBC News  

So I've been building my own coils for a short period of time and I'm looking to better understand how my coils can affect my vaping experience, specifically varying ohms and wattage's.

I've been building mainly only one coil as I'm still trying to better understand the basics of coils and more importantly wicking. Ofc all I hear these days is how sub ohming is the best and with all the sub ohm devices I feel like I may be missing out on something if I'm not at .5 or below.

The coil I've been wrapping is a 28g .9 ohm single coil. If I were to go lower, how does this affect my vape on a regulated device? Unless I'm missing something, only the heat flux and quickness to heat would be affected right by lower resistance (given a set wattage)?  

I am trying to get the best flavor with the best single coil build.

Objectives:
Flavor Smooth Vapor
Materials:
Kanthal Wire 35mg Nic Salts
I have noticed that either depending on the diameter of the coil or the spacing of the coil wraps You get a different kind of vape hit. It seems like higher gauge wire produces a smoother hit. And then couple that with a small diameter coil build, plus squishing the coil together to remove all coil spacing results in the smoothest possible vapor.

Can anyone confirm my findings? Or does anyone have any tips because I have still to replicate the smooth hit from clearomizer sub tank cartridge's that are non mesh. I am starting to think this is because the cotton is wrapped around the outside of the coil instead of being shoelace through the middle of the coil.  

I got my first Derringer today. Wanted to try it immediately although I bought it with the DAY AFTER (May 2106) in mind... but you know how it goes, you get a new toy and you want to try it out.

I'm really not into very low ohms so first I went for a single coil - 26 AWG Kanthal, 9 wraps for around 1.3 ohms. But I didn't like the way that could be wicked in an rda. So then I put in two 28 guage coils which I had previously coiled for my other atties. Together they gave me .8 ohms which is sort of ok. But I still am not quite happy with the wicking. These coils are 2mm internal diameter and there's not a lot of cotton you can put in there. The taste is good but my wicking is nowhere as fat as I see in some pics online.

Any advice?  

I recently picked up an infinite origen v2, my first build was single coil 2.4mm and it was not good on flavor, next build was dual coil 2.4mm at .5ohms, it was better on flavor. No matter what single coil build I try the flavor is just not there. Any suggestions on great flavor builds???  

Hello
I have the wotofo serpent rta top airflow single coil tank now and I just purchased the augvape druga rta. Flavor is 100% better in the augvape drugA rta but juice leaks out the bottom of the tank every time which is why I have to stay with top airflow as it never has leaked on me. So I’m looking for a top airflow rta single coil . I typically vape between 20-30watts so I don’t need a powerhouse. I just want the flavor and don’t care about clouds. Can anyone recommend the best top airflow rta? The wotofo serpent works well but it takes a hit on flavor. The serpent only has 2 small air holes around the coil area and I think this is why it isn’t producing a good vape. I was looking at the Zeus? Augvape intake of the dual one? Or any others anyone can recommend ?

primary goal: outstanding flavor
No leaking
Lots of air holes around the coil


thanks for your time