My Smok 22 Vape Pen Fire Button Is Jammed Please Help

I just got it today, and the batteries wouldn’t fit but I finally pushed them in. I don’t know too much about voltage but it says R on the left side, and u on the right side on the main screen. It’s at 0.27 voltage where it says R, and nothing for U. Is there something wrong with the voltage or the battery?  

I caMe home from work and seen my topside single was lit up on my dresser.I hadn’t used it in a couple days so I picked it up only to see that the wattage is going down non stop and won’t fire and it’s as if the wattage down button is stuck. It’s not though. I can’t find anything small enough to take the panel off so I pretty mad. Only
I’ve had Mabye 40 refills with this mod and never been dropped . Just use it on the weekends when I drive mainly that’s it . This is why I hate regulated mods. Anyone else have this problem? I don’t know why it doesn’t even come with a Alan key to
Take it apart.  

hi i have and endura Endura T18 vape and it is fully charged and full tank but when i press the button it goes orange and is still orange when i take my finger off the button but then it goes off. when i press the button the cape is not firing and doesn’t work. what do i do?  

I've got a couple of these little mods and both have the same problem. They continue to fire after the button is released. When it happens the display changes to the power on/off and keeps firing until the unit restarts (presumably after the 15 second cut off?). I can only think that the mod is registering 3 presses when I fire which triggers the screen change, and there is a bug which stops the release of the fire button registering. Anyone experienced this? Any fix? I'm surprised it's happening with two units so it must be happening to someone else!  

Well this sucks, I have an iStick 30w and toptank mini, I ran out of pre made coils so I thought i would try the RBA of the toptank. At first it read out as “protection” upon trying to fire it (I think the ohms were too low on the pre made coils included with the RBA at .1), then it said low battery (it was almost fully charged) so i plugged it in and tried to fire it once more and the thing started smoking (no protection message this time, just a little puff of smoke within the LED window). I only fired the button for a split second and it still seems to be functioning. Not sure what I should do lol or just ditch out on it? It appears to be working yet but stinks like an electrical fire now. I’m kinda reluctant to use it (I still have an old coil but it was starting to taste funky). Any advice or idea what might’ve happened?  

I accidentally locked the up and down buttons by pressing both of them simultaneously for 2 seconds, I have tried unlocking them by doing the same thing like the instruction manual calls for. It doesn’t work, no “unlock” pops up or anything. You can hold them as long as you like and...nothing.

I have since figured something might be wrong with it as I am almost positive I’m doing it correctly. Now I have tried getting the reset button to work in hopes of the up and down buttons being unlocked upon reset. I hold the reset button for 5 seconds and I’ve tried the method of the combo with the fire button and reset as well as the up arrow and reset and the screen goes blank and turns back on but never says reset and the settings are still the same as before.

My next idea is plugging it into my computer in hopes of an update fixing this but other than that I am out of ideas. The device is stuck on 20 watts which is too high for the cartridge I’ve got on it. Does anybody have any ideas, please help me out.  

I hope I am posting this in the correct place.

Up til this year I have run mainly utilitarian stuff and it’s served me well, I have to say. I have however been looking at some of the rather beautiful stabwood mods folk on here have, and am considering one, especially now I have found a custom maker up by Loch Fyne near to my other house in the West of Scotland.

I have a few questions which I hope members can help with.

Do you use them when you are out and about as daily drivers, or do they need special care so you only use them at home?

I had a hand made wooden squonk mod a few years ago and the wood didn’t stand up well to leaks or coming into contact with e liquid which eventually jammed up the fire button. As stab wood is made using a resin - is it impervious to this?

Is stabwood prone to cracking over time?
And finally with reference to the Pumper squonk mod - the bottle and pump system is proprietary so is it long lasting and does it have any common faults?

Many thanks in advance for any information you can offer.  

Right now I have a few box mods, the IPv3, SIG 150w and the Snow wolf 200w. I'm using the Snow wolf 200w and honestly I'm not happy with it. I've had the button stick a few times causing it to auto fire and I'm noticing an almost one second delay from when I hit the fire button to when an actual vape starts to kick in (very slow fire up time, and I'm only running dual twisted 26g) on top of that I really dislike that I have to hit the fire button to see how much volts I'm using. I know the SX M class is one of the best out right now, but the fact it's a single battery concerns me because I typically vape between .12-.20 ohms and usually 60-80w (but since getting the derringer it's been 60). I really like the hot, dense flavorful vapes and I wanna make sure if I get the SX M class it'll be able to deliver that.  

I have a smok rpm80 which is a aio pod system and when i am in a quite enviroment and press the fire button to vape, my ecig makes a noticable electrical buzzing noise. Is that normal and/or does anyone else have this problem or know how to fix it?  

I busted my tank and my local store didn’t have another so I just decided to buy a whole new head/tank to go on my SMOK morph 219 mod. I asked the store clerk several times before I made the purchase if the tank I’m buying is compatible with my mod. He insisted it would work. Well now when I get it home and try to use my new tank on my mod (SMOK morph 219) it keeps asking if it’s a new coil with a different size every time. Any advice? And no I didn’t forget.... the new tank is a vaporesso cascade tank 7ml. 60.5X25MM 81g.