Let's Get Serious For A Moment

Wich finger u guys use to press fire button on mod???
Index or thumb????  


Similar Content



Help!

hi i have and endura Endura T18 vape and it is fully charged and full tank but when i press the button it goes orange and is still orange when i take my finger off the button but then it goes off. when i press the button the cape is not firing and doesn’t work. what do i do?  

Smokless Owl Firing Button Fix

I have had a lot of mis fires on my Smokless Owl 25.00 squonker and had to press down extra hard

and sometimes side ways to get it to fire.

I just done some contact cleaning and scraping on the Smokless Owl Button.

I took my wifes Emory board finger nail file thingy and depressed the firing button and held it depressed and rubbed it

across the firing pin and then took a small jewlers screwdriver and scratched it back and forth across the end of the pin and

did the same thing to botton ground pin.

I noticed some black color on the end of the firing pin before I started this cleaning process.

I gently took the screw driver and scratched back and forth across the positive and negative end of the battery just to

take any small film or oxidation from the ends just to make a better connection.

It seems to fire now just like it should with no MISFIRES---mod is now perfect !  

Problem With Device

Hey guys.. i been vaping for a while and not had this hapen before.. i am using a Hugo Vapor Rader and ot has been working with no problems until today... when i go to use it, when i try to fire, it says high atomizer the first time i push fire button followed by low battery (have tried multiple sets) when i press again. If i persevere and keep attempting to fire it works fine as if there were no problem until the next time i go to use the device when the process repeats.. i have taken the tank apart and cleaned and put back but the issue continues.. anyone have any ideas on what is wrong/what i should do?  

Vaporesso Gen

So I recently bought a brand new Vaporesso Gen mod. Normally I stay away from compression/press fit 510 connections but I decided to give the Gen a shot. I've only had it 1 day, and already I've noticed that the 510 connection is raised slightly above the top of the mod and with a tank connected it is slanted towards the back of the mod. From what I can tell the 510 isn't loose at all. But it still slightly worries me. And a couple times I've taken a hit and everything is fine. Then all of the sudden while my finger is still pressing down the fire button it stops firing. Has anyone else experienced this with the Gen?  

I Have Question

I have a smok rpm80 which is a aio pod system and when i am in a quite enviroment and press the fire button to vape, my ecig makes a noticable electrical buzzing noise. Is that normal and/or does anyone else have this problem or know how to fix it?  

Smok Xpro M65 Problems

I've got a couple of these little mods and both have the same problem. They continue to fire after the button is released. When it happens the display changes to the power on/off and keeps firing until the unit restarts (presumably after the 15 second cut off?). I can only think that the mod is registering 3 presses when I fire which triggers the screen change, and there is a bug which stops the release of the fire button registering. Anyone experienced this? Any fix? I'm surprised it's happening with two units so it must be happening to someone else!  

Very Tempted To Get The Sx Mini M Class, Not Sure If It's Right For Me Though.

Right now I have a few box mods, the IPv3, SIG 150w and the Snow wolf 200w. I'm using the Snow wolf 200w and honestly I'm not happy with it. I've had the button stick a few times causing it to auto fire and I'm noticing an almost one second delay from when I hit the fire button to when an actual vape starts to kick in (very slow fire up time, and I'm only running dual twisted 26g) on top of that I really dislike that I have to hit the fire button to see how much volts I'm using. I know the SX M class is one of the best out right now, but the fact it's a single battery concerns me because I typically vape between .12-.20 ohms and usually 60-80w (but since getting the derringer it's been 60). I really like the hot, dense flavorful vapes and I wanna make sure if I get the SX M class it'll be able to deliver that.  

Ipv Mini V2 Help!!

Hello everyone I recently purchased an ipv mini v2 and I love it, it is working perfect. I only have one complaint the fire button rattles like crazy and it drives me nuts. To some it's not a big deal but I just don't like it. So do any of you out there know if there is a way for me to fix this? Once again everything else is perfect ohms and all that it's just the fire button. The wattage up and down buttons are supper tight and clicky. Any help would be greatly appreciated. Thanks  

Mvp 3.0 - High Pitched Noise

Hello everyone. I just got my new MVP 3.0 today and am absolutely in love with it. I do have a bit of a question though. I just noticed a few minutes ago that when I press the fire button, it begins to make a quiet rather high-pitched noise. It's hardly noticeable, but definitely there. Is this normal, does anyone else with an MVP 3.0 have this occur?  

An Undiscussed Side Effect Of Vaping...

I have a callus on my thumb from hitting the button.