Creating Coil Wire, Or Find What I Need.

I got my first Derringer today. Wanted to try it immediately although I bought it with the DAY AFTER (May 2106) in mind... but you know how it goes, you get a new toy and you want to try it out.

I'm really not into very low ohms so first I went for a single coil - 26 AWG Kanthal, 9 wraps for around 1.3 ohms. But I didn't like the way that could be wicked in an rda. So then I put in two 28 guage coils which I had previously coiled for my other atties. Together they gave me .8 ohms which is sort of ok. But I still am not quite happy with the wicking. These coils are 2mm internal diameter and there's not a lot of cotton you can put in there. The taste is good but my wicking is nowhere as fat as I see in some pics online.

Any advice?  

I am trying to get the best flavor with the best single coil build.

Objectives:
Flavor Smooth Vapor
Materials:
Kanthal Wire 35mg Nic Salts
I have noticed that either depending on the diameter of the coil or the spacing of the coil wraps You get a different kind of vape hit. It seems like higher gauge wire produces a smoother hit. And then couple that with a small diameter coil build, plus squishing the coil together to remove all coil spacing results in the smoothest possible vapor.

Can anyone confirm my findings? Or does anyone have any tips because I have still to replicate the smooth hit from clearomizer sub tank cartridge's that are non mesh. I am starting to think this is because the cotton is wrapped around the outside of the coil instead of being shoelace through the middle of the coil.  

I never used anything but Kanthal and Nichrome wire to build my coils.

All things being 100% equal (wire gauge, coil type, coil diameter, ohms, etc) do SS coils require more power to run to get the same vapor as the exact same coil/resistance made from Kanthal or Nichrome wire?  

Hi, despite all the info on the internet these days, I ve been unable to find an answer to what is the life use of a wire on a rta coil (not the cotton or liquids) before it gets exhausted and become a bad element to health, maybe to the point of releasing metal particles that could go into the lungs... I know this is highly relative and depends on what kind of wire, liquids and vaping frecuency, but if I give you a straight case, maybe I ll make a good relation between other materials and their durability. It happened that during 2020, with the pandemic on full first impact, importations were very slow and in some cases, closed for long periods of time, I was trying to get some imported wires but I didn't have enough luck to find those I needed, just very thin wire for mtl equipment, which I didn't have. All was sold out from vaping websites... I ve managed to get a Zeus X rta and with it, the included premade coils (I think these are Nichrome)... Thing is, I used the same (and only) metal coil for almost 6 months, obviously replacing the cotton when needed (I had all the other materials, bags of cotton Bacon, tools, fresh liquids, etc), the liquid I ve been using is Don Juan sweet tobbaco and reserve, from King Crest. In those six moths I didn't vape all days or weeks, since finding or importing liquids were also a problem, so confinement and the lack of products, push me to smoke again, sadly, but I didn't give up and I start to build again the coil meanwhile the purchases arrive from other countries. The metal coil doesn't seems to be exhaust in plain view, it gets datk or black, as normally should be after several days of use and when tasting a bit burnt, but once I clean up with a brush, water and some short dry burning when building again, it gets back its grey metal color, not the same shine as a new one, but close. My vaping frequency was sometimes in chain, due to anxiety, but not all day or days and I was careful to rebuilt often. Mods are one Aegis X and one Smok P3, wattage I use is between 40 and 60 because even if the coils can be auto detected and suggestion is 75w, this is always overrated and burning taste triggers in 3 days. Only thing I did notice was sort of a metal taste for a period of time, that after went away and never got back. If someone wants to drop an answer, be welcome please, thank you all...  

Hey all.

So I've been vaping since January. I started out on a kanger ego and an aspire k1. Since then I've gone through aspire cf batteries, and finally made my way to my current set up. An mvp 3.0 or istick50w with my subtank mini.

At first using the stock occ coils with the subtank, I decided to buy some wire and cotton and here I am. Been building my own coils using the RBA section and loving it. I wick it properly and never get a dry hit, going anywhere from 18-25 watts, which is my preferred settings.

Now, it's only my preferred settings because I can't seem to go any higher. On either device. I get dry hits like crazy despite pancake wicking which I've specifically done to prevent said dry hits. I always have heard that it can possibly taste better the hotter it gets. And I don't mind a hot vape. But it won't let me try!

I'm well saturated, well wicked, and my juice can be anywhere form 50/50 to 70/30pg. I can do quick pulls on fully open, and slower toots on the middle setting on the subtank. I just can't go any higher than 25watts and I don't know why!


And that's not for just the coils I built. It's for the stock occ .5 ohm coil as well. And like I said all my cotton is beyond well saturated. Any help?  

So I've been using a Kayfun v4 and provari p3 using the hybrid connector and have never been able to get th ohms below 2 using .2mm guage kanthal bought from Vape escape one 2 mm coiling tool and about 6 wraps was initially happy with that but after reading the results other users are having they typically end up around 1.2 1.4 ohms using far more wraps then I have been using I tried to increase my coil diameter to 2.5 mm and the ohms exploded to 5 ohms making it unusable I have noticed that my spring in the Kayfun gets incredibly dirty and charred with what I can describe only as soot if anyone has any insights into what could be going on I would much appreciate it ive been enjoying my Kayfun but I'm still looking for that mind blowing Vape I keep reading about  

Dear forum!

here goes my strange experience:
I’ve been coiling and wicking for years pretty much the same way, and it was kinda ok = I adapted to all the quirks I had.

Recently I built a new coil, but instead of 4mm I decided to make 3.5mm coil. Same wraps number.
Wicked it as I alway do - exact same material, thickness (adjusted to coil diameter of cores) trimming etc.

And wow!
No problem with TC now!
Works reliably, no leakage, I can chain wape the whole tank!

could this one Change in coil diameter choice did the trick???

Or is it a fluke? (Well I’ll find out when I’ll built next coil same way...but still)

best regards
Vadim  

So I decided to try a 1,6 ohm coil on kayfun v4 clone Tobecco and I am using 28gauge Kanthal with a cotton
wick on a Rdna 30 and its vaping well at 15 watts I have a kanger subtank mini coming in the mail and here goes my question
So the kanger subtank states that with a .5 ohm coil i could vape up to 30 watts but the voltage comes in at like 3.8 volts
I was under the impression that the rdna 30 needs at least 4 volts to work which kinda brings me to my second question
What is the point of of sub ohms? cant i just build a 2.0 ohm coil or something like that to achieve the results as if i was subohming
I am very confused on this
thanks for the replys in advance
Oh yea is a 1.6 ohm coil at 15 watts a normal build or any recommendations for the kayfun v4 for watts and ohms thanks again  

I find keeping the voltage at 4.2 to 5 max will give me the perfect vape.It works out too using ohms law.For ex:,if i wrap a coil at 1.5 ohm,i set the watts at 12/13 and it works out too 4.2.

If i do .20 wrap i can ''bump'' up the watts to 50 and it will still be about 5 volts with no burnt taste.

Ya cant break ohms law.  

First off, I would like to say that I’m very new to vaping. I started off with a JUUL, then a Smok Novo 2, and eventually got sick of buying pods.

Now I have a Hellvape MD, and an Ares 2 - the first provides better flavor, but it’s still not comparable to what I was getting in my pod systems. I just recently purchased a BP Mods Pioneer, and I’m hoping that gives me better results. I’m using an Aegis Mini for a mod.

I’m trying to figure out what I’m doing wrong, because it’s really frustrating to spend all this money for worse flavor, when I was hoping it would let me save money.

I have about 40 bottles of salt nic flavors that are 50 or 35 mg, and a couple 3mg freebase I bought (120ml for $7 seemed like a steal). I would really like to get away from the salt nic, but I seem to get even worse flavor from the 3mg.

I’m using 2.5ID 28ga SS316L round wire from Master Wire Supply (I have a spool) with Puffs Organic Cotton. My coils are usually .7ohms, but I’ve tried up to 1ohm. I’ve also tried 1 ohm Vandy Vape Superfine MTL fused claptons, and experienced similar results.

I’m using the MD with the most restrictive airflow settings (3 small hole airflow disk), low (2-3) adjustable AFC setting. I have my coil as low as possible to the airflow, and I have thinned / fluffed my wicks.

I haven’t tried adjusting the airflow below the coil on the Ares 2, because the video instructions say wide open airflow below the coil is the best for flavor (I have found the opposite to be true for the MD).

Can someone provide me more insight?

Will 2mm ID coils with the same amount of wraps taste better than 2.5? Do coil ohms do anything for flavor, or does it only change how fast it heats up? Will I lose flavor if my coils hang outside the diameter of the airflow disk?
Is there a certain type of coil that would give me better flavor than regular round wire?

I use TC at 420F 20 watts


Any kind of feedback is appreciated and if I left anything out or you have questions about my set up that could help me out please ask! I’m at a loss on what to do, and it seems like no amount of research is helping