Hey everyone.
I have a Squid Industries V2 white camo. Got really worn down so I decided to sand it down to make it amazing.
I want to put a golden crucifix cross on the side opposing the Squid Industries label, to make it genuinely one of a kind.
Would black seem too boring and look like the black they already supply? I was originally wanting to make it look brass, then I thought of a cross "which I don't have or know where or how' and changed my mind.
Suggestions!
Hey everyone I'm fabricating my old beat up Squid Industries V2, on another post.
Any ideas on how to make it mechanical? If I could do variable voltage that'd be awesome, or have a limiter for volts or something.
Screen not turning on? Inconsistent firing? Not powering on and/or inconsistent power?
This is how I fixed mine and it may work on yours.
Disclaimer: Always attempt to contact Squid Industries warranty services first to see if they will replace it. You can find the email on their Instagram page. If that doesn't work, try what worked for me.
- Step 1: Remove batteries. Hold power button for 10 seconds.
- Step 2: Unscrew the 3 screws at the top. 2 are star-head and 1 is a very small Phillips head.
- Step 3: lightly push upwards on the fire button. If it will not come up, try reaching in the battery compartment and lightly pushing upwards with a finger or back end of a screwdriver.
- Step 4: Once the component is out, lightly separate the two halves by wiggling the pin connector out of the socket. Don't pull too hard. Don't want to rip out the wires which will stop from separating the two halves entirely.
- Step 5: Cleaning time. Dab off the majority of juice with a paper towel. Grab a soft toothbrush and a small cup with rubbing alcohol. Lightly brush the Alcohol over the visible surfaces. Wait until it dries. Repeat until it no longer seems oily after drying off (once or twice should do it).
- Step 6: Take a look at the red and black wire connected to the underside of the bit your tank/RDA screw into. Does the red wires rubber sleeve not cover either end of the wire? Can you see the metal wire? If you do, proceed to the next step.
- Step 7: See the black goop that is melted onto the underside covering the solder? Go ahead and carefully pull that off, as much as you can. Don't pull at the wire, just the black melted rubber goop that is over the solder.
- Step 8: Using your fingers or very lightly with a set of pliers or tweezers, stretch the red rubber sleeve over the exposed wire. Alternatively, if you are good with electrical tape, you can use that to cover up the exposed wire.
- Step 9: Grab an inch of electrical take and slap that over where the black goop was. Try to press it to the surface and wires as good as you can get it.
- Step 10: Make sure all the alcohol has dried and put it all back together. If you'd like, you can attempt to put a rubber band around the seam to prevent future juice from getting in (I didn't, but I thought of it afterwards).
If the juice was messing with it, it should work. If the power was shorting to ground, it should work. If it still does not work, contact Squid Industries and politely request to purchase a new chipset for $35 instead of buying a whole new vape.
Wismec 3 Battery? No good. Breaks within a year without dropping. Replicated on two mods.
Wismec 2/3 mod? Yet again, poor manufacturing. Wires not soldered properly. Almost lasted a year.
Squid Industries Double-Barrel? Craps out after 1 month without any damage. Wont turn on.
GeekVape Aegis Legend? 2 months and not reading the batteries right. Never so much as tipped over on my desk.
SMOK? Had more than I can count or bother to recall the exact models, but every one busted within a year.
None of them seem true to their warranties either. They make it as tedious a process as possible. I haven't tried with the Aegis Legend yet, but I'm going to go out on a limb here and say it's probably more of the same.
At this point, I am convinced that I have spent more money on mods than I have on juice. These mods are all made like crap. I don't want to spend $80 every few months to get a new mod. I just want to vape for gods sake.
Has anyone had a mod that has lasted them over a year? What kind was it? I've asked this before and that's what led me to the Double-Barrel and the Aegis Legend. Both have failed on me even sooner than my previous attempts.
Kanger SUBOX Mini White Starter kit Pre-order now, Please do not mix t – KangerTech
This black and white one is so sweet I GOTTA get one... you guys see this?
Im gonna need Kanger to stop stepping up thier game like this I wasnt ready...if this turns out to actually be as great a mod as it seems from the specs this is gonna be as big as the Subtank.
Only thing I donty know about is that black and white looks like paint on the subtank, I dunno if that'll stay on for long. It might look bad quick.
I relapsed this morning after 93 days.
I don't even understand why/how. I have so much gear/juice that it doesn't even make any sense. I just had this huge urge to go buy some and I did, and I had two of them. It was like I'd never even stopped.
I am so guilty right now that I can't even face anyone I know. I don't understand why this would even cross my mind after 3 months...much less actually do it. I mean, there are several steps...drive, spend money, drive back, smoke.
Very unhappy.
Why are they all made from soft brass? Even the silver colored ones are just plated/painted over brass and even being overly gentle and careful, they're designed to strip and wear out.
Where can I get one made from stainless, or at least steel? I'm talking about the threaded portion. The positive anode being brass is fine by me.
People are sticking aluminum foil and other things in there to take up the slack, but these are temporary fixes that won't be durable. Using wood or paper only inhibits the conductivity of its intended purpose.
I'm guessing the threads on my SubTank Plus portion (male threads) are actually stainless, which is a good thing, but the (female) threads in the KBOX are losing their silver color, leaving metal shavings on the tank's threads, and slowly turning brass in color.
I properly lubricate these threads, and I'm extremely gentle as I gingerly thread the tank on (NEVER cross-threading), but I can feel it getting looser as the days go by (only 6 days old), and can visually see the slow change in color inside, from silver to brass.
I'm tempted to solder some jumper-cables to my tank, and leave the box-mod in my pocket. I want to try to make my own female connector from some grade-8 nut, then epoxy a center-pin in there, then hardwire it to the KBOX, after ripping out its brass 510. Maybe use an NL-4 Neutrik™ connector instead. This area needs improvement!
I own a black troll RDA. I love it. The thing is amazing. But, it looks goofy as hell on top of my Sigelei 150. I'm looking for a stealthy mech mod, preferably black, that I can use as a pocket Vape with my troll. I would like it to be able to use 18650's, as that is the only type of battery I own. Any suggestions?
So Aspire have announced an Atlantis 2 and Atlantis Mega along with a CF Maxx battery.
Will I purchase these? Yes! Am I excited? No!
Aspire revonutionalised the vaping world with the birth of the Nautilus. When the Atlantis arrived everyone was excited that Aspire had made a new model, and expectations were high! No way am I claiming the Atlantis is garbage, but after looking at it, there wasn't really a big wow. It just kind of looked small and boring! But performance is the main point!
KangerTech most likely Aspires biggest rivals had taken first place with their SubTank series! Although I hate Kanger! The more options and reliability were so much better than the Atlantis!
When I heard Aspire were releasing these I had high hopes that we would get an Aspire RTA with more Ohm option stock coils and a 50W 18650 MOD! But... Apparently the Mega tank and the MOD is 30mm so pretty big! Also it charges from a USB and there is no rebuild section! So all in all a few minor upgrades including drip tip changes and more airflow. But nothing that will make you want to buy one straight away. I'm an Aspire fan! I will support them and make a purchase regardless! Just think they could of done more!
One last thing! I was kind of put off of the fact they called it the Atlantis Mega! When there's Kanger AeroTank Mega! I would of thought they would make the effort and come up with something more unique!
Video he https://m.youtube.com/watch?v=swQHODWlqMA
Hey friends,
So I was just reading some news on my phone and I'm seeing several articles about BANNING FLAVORED EJUICE within 30 days....?
If this happens will none of us have access to flavored EJUICE in stores or online? Will it only be banning flavored ecigs (like juul) ?
Anyone with any info on this topic please let me know.. in my opinion, the tobacco industries lost WAY to much money due to vaping.. and this is their way to get it back. I feel a lot of people would go back to cancer sticks.. we know for sure smoking causes cancer, so why gave they yet to ban cigarettes?
I'm worried for the whole vaping community but I'm still not sure of the accurate details.
Kelly
I make the choice that I'm certain I'll be vaping forever. I figured since I enjoy it, I'm gonna learn everything I want to know and make it a hobby.
Me being a perfectionist, I decided it was time to piece together a setup that was not only powerful, but pleasing to the eyes.
After much consideration, I made the choice to not go sub ohm. I instead decided a higher power, higher ohm setup would please me.
So this is what I ended up with.
Aspire CF VV 1600MAH battery. Instead of rocking a VV+ most people use, I went the route I did to get 600 more MAH battery and didn't care about the beauty ring because after all, my Aspire K1 tank is a backup now and can't be used with the VV+
The tank had to be good too. This was where I wanted to upgrade the most. I wanted adjustable airflow, and better coils.
The Nautilus Mini was the only clear choice. 2ml is fine for me as I switch flavors now and then, and the new redesigned OCC coils you can purchase was a selling point.
I've been using the setup since last night, and WOW!!! This tank brings the flavor through in ways I never thought possible. Also, the vapor production is amazing to me. I don't care about cloud chasing so by my standards this is a fog machine at higher voltage lol.
Overall with 5 additional spare coils I'm about 65$ in this setup and that's a bargain. It performs so well.
Also wanna throw out that GWAR Spew from MBV is friggin amazing in this tank!!!!