The protruding collar on the hinged cap, where the drip tip is pushed onto, has a perished o ring. There are two tiny o rings here and the perished one means my drip tip falls off. I am not sure what I need to order to replace the o ring. Could someone with more knowledge than myself suggest to what I might need please? I am in the UK.
Hi vapers.
So I wanted to change out the o-rings on my Crown IV tank as it has a bit of a leak when it's almost empty....
However, I can't figure out how I'm gonna get this o-ring out.
Any tips ?
Any ideas are much appreciated ! Thx !
EDIT: Got it out with a tiny dab tool !
I saw somewhere on this forum that you can use a beauty ring as a catch cup for RDA, so I bought those: Deck Beauty Ring for Entheon RDA Atomizer (5-Pack): FastTech Forums
Problem is that my atomizer doesn't screw completely and my vaporizer doesn't detect the atomizer so it doesn't work.
I don't really need it as it doesn't happen often that I over drip but it happens sometimes. Is there something I can do about this problem?
My favorite drip tip has a busted o ring and the other one on it is not fairing so well either. It is one from Suicide Bunny and i have taken some orings off other drip tips and they did not work out so well. I am also a big erkronogin used and those two small o rings on the top disappear very fast. I know those are 3x1 but that does not tell me in ID. Does anyone have a good place to get replacement Orings at? I have looked all over the place and since i am not really sure what i am getting i dont want to have a million orings around. Now i did find an oring set on ebay for about 13 and was thinking about picking that up. It says it has the 3x1 in there.
It was only about 5 feet to a hardwood floor, but when I looked down and saw two pieces lying there it caused a bit of panic.
I'm building a staircase in a new house and I leaned a little too far over from the landing with the rig in my shirt pocket. I really need to find a good holster for this thing.
After finishing what I was doing I scrambled down to assess the damage: the tank section of the nautilus had separated from the knurled ring just below the AFC ring. It's a friction fit set-up, and after cleaning the juice and sawdust from the parts I was able to tap everything back together with my hammer. I pushed the button on the Provi and nothing happened. Pushed the button a couple more times and I was back to vaping again with no leaks.
The owner witnessed the whole episode, and there wasn't even a dent in the finished oak flooring. He laughed as I cleaned up a couple of juice spots where it hit and watched me put it back together with a hammer.
I'm not usually this lucky.
Big shout-out to the makers of both products.
Yea yea E Juice I know
But... still ...
Nothing petrolium based as that can kill ya ----- ok so no chapstick
but how about burts bees wax isn't that all natural and ----ok to lube my O Rings with ??
http://www.e-cigarette-forum.com/forum/general-vaping-discussion/654241-noop-tip-o-rings.html
Got a few old rda and rta need an oring or 2, I found packs in harbor freight but not much good although they have ~20 sizes inside, wondering if anyone has a good, quick idea for packs of many sizes of orings for our application, from Drip Tip sized to cap sized and all In between
Hi Guys, If I don't use a spiral drip tip I get a dry mouth. I bought a bunch of innokin jems because the aspire k2 is discontinued. But the Jem the drip tip is attached to the top. Can anyone suggest anything, Maybe there is some other kind of top that would fit it or something, because I've spent quite a lot on them. I normally get my supplies from fasttech.
Thanks for your help
Purr.
I've got a VTR that i was using with an aero tank, but was burning through coils like every 4 days. Local vape shop recommended the nautilus mini since that's what the owner uses with the same juice I use. Doesnt quite fit with the VTR ring, but they showed me how to screw the base in and just pop it in that way. Cool, no problem right? Yeah right.
I go to refill and i cant get this ....ing thing off at all. The 510 connection is not stuck in to the device, but the bottom ring to unscrew the glass part is just not budging at all. So now I basically have a inert device and tank that cannot even be used and I'm out 52 bucks in total for this damn tank and coils.
I recently purchased a Provari 2.5 and am using an Aspire Nautilius Mini. I am looking at getting into RTA's and am looking for a little feedback. I want to order both but just want to keep costs down as I just forked out for the Provari. Gonna order from FTech.
Also will it fit my Provari or do I need another ring as I seem to think it may look awkward.
For most atties, are the 510 center pins the same? Actually, I asking about rebuildables like RTAs. Same length, diameter, threads, ect? Can you even get replacements? I need some that "protrude" more from the 510 connetor. I know, someone suggested just adding a tiny or-ring but I don't trust that would be strong enough.