An Mtl Vaping Quest

What is your go to single coil build in terms of gauge wire, diameter, and number of wraps : (no fancy Clapton or twisted build just a "regular" wrap)

And if you have a reason please include it: For example: "I'm a flavor junkie and this is best flavor build I've found" or "I like short ramp up times" etc ...

(I know preferences may vary greatly)

Thank you very much

:


Sent from my iPad using Tapatalk  

I never used anything but Kanthal and Nichrome wire to build my coils.

All things being 100% equal (wire gauge, coil type, coil diameter, ohms, etc) do SS coils require more power to run to get the same vapor as the exact same coil/resistance made from Kanthal or Nichrome wire?  

Just a little warning to all who have purchased the Lemo 2- Do not use the wire included in the box.
I was a little worried when i was using the stock coil and noticed it had been turning a green color after a few days of use, not sure if this is the case with all Lemo 2's, but if you notice your wire is turning greenish, just throw it out and replace it. I don't believe this is kanthal, it could possibly be nichrome, but it's properties are not matching up with those of kanthal. My worries were confirmed when I decided to put a parallel 5 wrap coil on my rda with that wire because of my lack of other 24 gauge... Well today when I took out my cotton and dry burned the coil a little to rid it of excess juice, the coil actually deformed and somewhat melted on my rda . I don't know what kind of metal this is, but I'm positive it is not kanthal, this has never happened to me with kanthal, and this wire seems to be of a lower resistance than kanthal. Anyway, just wanted to let ya'll know to be careful with that wire, or just throw it out altogether. Otherwise, the Lemo 2 is a fantastic tank  

so in my pursuit of vaping above 200 Watts I made a fuse 3x24ga gauge wrapped with 36 gauge and I tried three coils. it came out .07 I Vaped it at about 375 watts it was a hot vape but the ohms were very low so I had a problem with power my DNA 250c was reporting 65 amp output so I took that and put in dual fuse 22ga gauge wrapped with 36 gauge I ran that build triple coil I used it at about 250 Watts. what I am trying to do is vape at about 300 to 400 watts with an ohm or .2 to .3. the inner diameter will be 5.5 or 5 mm I'll be using the kanthal core wrapped with 36 gauge and ni80.I'm trying to figure out what my next bill should be to try to vape above 300 watts the restrictions I have is it can't be below point 1 ohm or above .3 ohm I have two aromamizer plus has with the series deck The parallel deck a second parallel deck and a single coil deck. The single coil deck fit 6.36 mm.

I also have the aromamizer titan.

What gauge would you Clapton?

Sent from my HD1907 using Tapatalk  

I recently picked up an infinite origen v2, my first build was single coil 2.4mm and it was not good on flavor, next build was dual coil 2.4mm at .5ohms, it was better on flavor. No matter what single coil build I try the flavor is just not there. Any suggestions on great flavor builds???  

First off, I would like to say that I’m very new to vaping. I started off with a JUUL, then a Smok Novo 2, and eventually got sick of buying pods.

Now I have a Hellvape MD, and an Ares 2 - the first provides better flavor, but it’s still not comparable to what I was getting in my pod systems. I just recently purchased a BP Mods Pioneer, and I’m hoping that gives me better results. I’m using an Aegis Mini for a mod.

I’m trying to figure out what I’m doing wrong, because it’s really frustrating to spend all this money for worse flavor, when I was hoping it would let me save money.

I have about 40 bottles of salt nic flavors that are 50 or 35 mg, and a couple 3mg freebase I bought (120ml for $7 seemed like a steal). I would really like to get away from the salt nic, but I seem to get even worse flavor from the 3mg.

I’m using 2.5ID 28ga SS316L round wire from Master Wire Supply (I have a spool) with Puffs Organic Cotton. My coils are usually .7ohms, but I’ve tried up to 1ohm. I’ve also tried 1 ohm Vandy Vape Superfine MTL fused claptons, and experienced similar results.

I’m using the MD with the most restrictive airflow settings (3 small hole airflow disk), low (2-3) adjustable AFC setting. I have my coil as low as possible to the airflow, and I have thinned / fluffed my wicks.

I haven’t tried adjusting the airflow below the coil on the Ares 2, because the video instructions say wide open airflow below the coil is the best for flavor (I have found the opposite to be true for the MD).

Can someone provide me more insight?

Will 2mm ID coils with the same amount of wraps taste better than 2.5? Do coil ohms do anything for flavor, or does it only change how fast it heats up? Will I lose flavor if my coils hang outside the diameter of the airflow disk?
Is there a certain type of coil that would give me better flavor than regular round wire?

I use TC at 420F 20 watts


Any kind of feedback is appreciated and if I left anything out or you have questions about my set up that could help me out please ask! I’m at a loss on what to do, and it seems like no amount of research is helping  

So I decided to get another clearomizer and the Donner by Amigo Itsuwa is what I got to replace my Aspire Atlantis.....
So here are my thoughts on it and it's just My Opinion:

Holds 4mls of juice - holds more juice so I'm not refilling my tank 2-3 times a day
.50hm Coil head is cotton & Kanthal wire & a wire mesh around the opening for better wicking ( You can use Atlantis coil in this thing and it's better in this tank then it is in the Atlantis) It comes with 2.
There's no notches or trying to center the coil head. It sits in the Clearo and just sucks juice lol
Great Flavor sub-ohm - The flavor you get from this is amazing, I was a little taken back bc I chose a sour raspberry and it really was more sour tasting then in any of the other tanks I had the same juice in
I personally like the drip tip but it's not for everybody
Adjustable air flow control is a wide slot - It's a slide around, but the draw from almost closed to full open is nice any way you wanna vape.
Vape production is great I use 10/90vg - 20/80vg


There are some things I don't like about this tank...
Priming the coil is a process - on a fresh coil the directions state to drop a few drops onto the coil, then once tank is filled let sit for 1-2 minutes prior to use. On your second fill of the clearo you have to let the coil sit for 2 minutes b4 use....I kinda wanna fill and vape, not fill and wait
Holding 4mls of juice is great, but if you can't vape 1ml of juice at the bottom of your tank it sucks. You can't vape the last ml of juice because the coil head sits to high so it can't wick the remaining juice.
I did find that when I put the Atlantis coil head in that the wicking was alot better then the coils that it came with, now this could be bc I am using a high vg juice.

So let's talk price....I bought this at a B&M so I paid A LOT more then what I've found online.
My price was $45.00
I have found these online for as little as $23.00
and for this price I would probably buy it again, not for $45.00
Iv'e been vaping on this for about a week now, I've gone through 2 coil heads in 4 days & now put the Atlantis coil head in it and am having better luck with it.
So there's my thoughts on my new clearomizer.  

Hey everyone,
I've been vaping for about two years now, and have decided to start dripping. For the last few weeks, I have been dripping on an IGO-W, 26G Kanthal single coil (7 wrap micro coil reading at 0.8ohms) on my iStick 30w.

I just recently purchased a new battery that should arrive today, and was wondering if anyone had advice/tips on producing some fat clouds! Dual Coils? Different coil builds? Number of wraps? Watts to vape at? I think you get the picture lol.

The items I will be using are as follows:
-SMOK XPRO M80 Plus
-IGO-W
-26 Gauge Kanthal Wire
-Japanese Organic Cotton
- 80vg/20pg Juices

All input is greatly appreciated. Thanks!
-Tyler  

Dear forum!

here goes my strange experience:
I’ve been coiling and wicking for years pretty much the same way, and it was kinda ok = I adapted to all the quirks I had.

Recently I built a new coil, but instead of 4mm I decided to make 3.5mm coil. Same wraps number.
Wicked it as I alway do - exact same material, thickness (adjusted to coil diameter of cores) trimming etc.

And wow!
No problem with TC now!
Works reliably, no leakage, I can chain wape the whole tank!

could this one Change in coil diameter choice did the trick???

Or is it a fluke? (Well I’ll find out when I’ll built next coil same way...but still)

best regards
Vadim  

I'm new to vaping. I've went through 3 coils barely using them.


My issue is: When I first install the new coil and add the liquid, it produces vaporizes just fine. It seems like when I set it down for an hour or so, and go back, it still produces good vapor. But after a bit, if I set it down after vaping, and go back, it produced no vapor no matter how much I puff it. It seems like if I unscrew the part where the coil is, and run it under water, and then let it dry, and replace it, then add e juice, it'll start producing vapor again. But it seems like as soon as I set it down for a bit, and pick it back up, there's no vapor and I wash it out again, etc then it works, but eventually just stops producing vapor altogether u til I replace the coil.

What's going on here? am I doing something wrong? Do I need to adjust the coil some how? I've bought brand new coils and barely use them and this happens. Is the coil just getting gummed up? The coils don't make vapor after so long, and the usage doesn't even equate to a full day, maybe an hour or so.