Help Me Find These Coils In The Us

Hey Guys,

I have been learning the ropes of RDA vaping, and so far I absolutely love it! As the title states I’m wondering what coils (FC, Aliens, etc) Would be best for flavor and vapor output? I’m currently running some Wotofo 0.33 Fused Claptons (~0.17 in dual coil) @ 60 Watts. The flavor and vapor is ok, But I’m looking for a little more. Maybe something I could run at a slightly higher wattage and get more vapor / flavor?

Any help would be greatly appreciated!

Thanks!  

To keep it short, my coils are lasting a day on average. I vape a 12mg store bought Skittles flavor and occasionally mix it with 18mg Menthol juice between 25-30 watts. The coils taste burnt and get clogged with some black crud. I'm priming the coils with juice, doing the dry hits that's recommended, essentially everything by the book but I can't get any decent lifespan out of these coils. Any insight would be greatly appreciated!  

Does old coils have any negative affects?

I typically burn off the gunk on the coils and put it through a good rinse then change my wick every few days. This was especially true when I'm using standard kanthal on the Protank.

I recently switched to a Solomon 3 using claptons. I find that there is very little gunk on the coils, I still burn off what I can before replacing the wick. I usually change the coil every week and one wick in between. On this one however, I'm 2 weeks on on the same coil and had only replace my wick once using the same liquids that I normally use on the Protank.

What I notice is the vape isn't as smooth as if I were to put in a fresh coil. I think I just answered my own question but what do you guys have to say about it?  

Hello vapers! first! I'm a noob at this stuff because I just buy my tank and use it with the coils it comes with and second, my english isnt that good but I can understand it perfectly fine.

Anyway, Ive been searching everywhere but I couldnt find a solid answer to my question.
Im using an Aerotank Giant right now with a 1.8 ohm coil, if I put a 1.2 ohm I would have to use less voltage because I get a burnt taste and the coil burns pretty quick, Im about to order a Sub ohm tank soon and I'll use the stock coils, the one im getting is the Kangertech SubOhm tank.
Why do subohm coils use more voltage when normal coils use less?

I mean, Ive seen people do things like 0.2 ohm coil @ 100W + If I did anything over 3.5V on my 1.2 ohm coil itd burn instantly... SubOhm takes more voltage the lower you go and normal dual coils take less voltage the lower you go!

1.9 Ohm Dual coil = 3.7-3.8V for me
0.5 ohm OOC subtank sub ohm coil = 12-30W?!

Thanks in advance for taking the time to reply to this post and your patience!

Cheers!

Edit: by the way, Im planning to use my subtank with a 50/50 PG/VG 16mg nicotine, Is that ok?  

Okay so not sure if this is the right section or not but its the only relevant place I could find. .

My first build was okay coils turned out fine but the wicking and position of the coils where terrible. So I decided to have another go.

Opinions appreciated.

Using smok xpro m80
Plume veil v1.5 clone
26gauge kanthal
Wrapped around a 2mil precision screwdriver.
8 or 9 wraps can't remember.
And reading at .46 ohms

P.s don't know why the coils look like there glowing purple but I promise their not haha.
 

Are items coming from FastTech taking longer to be scanned in as having arrived in the United States? I saw on my app that it left China on the 16th of March and it hasn't been scanned into the United States yet usually FastTech takes two weeks to get to my house. So I'm just wondering is that normal for right now is it taking longer for the United States actually scan things in?  

I have been vaping for 4 years now. I am using the baby beast tank. I have 3 of them.
I have never used anything else because,, well, it works fine for me. My problem is that I am having a hard time finding coils. I used to by clone coils on ebay for dirt cheap. There are no longer any coils on ebay. I cant find any coils online. They are either out of stock; or very expensive. What do people do nowadays? Do people still use the baby beast or has everyone
changed to something cheaper/better? I always use Q2 .4 Ohm coils. I only found 1 place online that has them and they are $20 for 5 of them (including shipping). What would you guys do? I was so happy with the clone coils. They were inconsistent but cheap. Some would last 3 days and some would last 10 days; but for $1.35/each I was happy.
Thank you for any advice you can give.
MrElder  

I am kinda a noob when it comes to prebuilt coils. I am looking for coils that feel very strong/sturdy, but I am not sure what material it is.

I had coils that said they were .25ohm and all it says is "KA1 WIRE + Ni80 wire" and they felt very sturdy/hard to pull the wraps apart etc....

I bought what I thought were a good replacement for those, but they feel flimsy and easy to pull apart the wraps. They are .36ohm, 316l stainless steel, 30gx4/36g.

So apparently the stainless steel wires are more flimsy...I cannot seem to find coils that have KA1 + Ni80 like the sturdy coils I once had. I
am trying to figure out which material/what I need to look for in order for the coils to be sturdy like the old coils.


Can someone help me out with this? Thanks in advance.  

I've been using 50/50. What's the best to use to extend the life of the coils? I get huge clouds with the 50/50 and am using a light colored juice. I get about a week out of a coil, could go longer but like a fresh coil. My friend had the same juice but 70vg/30pg and I found after the first hit it just does not seem to wick the best unless I let it sit a while.  

Everything that I have read so far says that you want to use spaced coils when working with Ni200. Will the coils not work as well if you use contact coils? I am asking because I have a Goblin RTA and it has a small build deck and Im not sure if I will be able to fit spaced coils in it (also, I have never made a spaced coil lol)


Thanks for your help guys!