Homemade Atomiser Info Needed

I have been making my own liquid for about a year now without any issues. I just cannot seem to adapt my recipes for my SubTank. I am getting way too much throat / lung hits which leads to immediate coughing.

My all day recipe for the last year is a 60% PG/40% VG mix with 25% flavoring and 18mg of nicotine. I tried this mix in my SubTank at 0.5 ohms and immediately started coughing. I first thought the nicotine was too high so I lowered it down to 12mg then down to 6mg but still coughing. I then thought I was using too much flavoring for 0.5 ohms on the SubTank so I cut my flavoring in half.....STILL coughing. I even tried lowering my PG ratio and raising my VG ratio and..STILL coughing! I have also tried lowering my wattage to no avail.

By this point I am getting pretty annoyed and cannot figure out how to get a nice vape on the SubTank with my homemade e-liquid. The only store bought e-liquid that I have on hand is a bottle of GQ Eclipse @ 6mg. I get a great vape from this liquid on the SubTank (running between 12 and 16 watts). Why am I having so much trouble getting my homemade liquid tweaked for the SubTank? Has anyone else experienced similar problems? Am I running my wattage too low? I am open to any and all suggestions.

By the way.....my most recent batch was 20% PG / 80% VG with 12.5% flavoring and 6 mg of nicotine. I am still coughing my *** off when I try this juice.  

I am a new member and everybody’s been helping me with various atomiser problems and I think I’ve been told to move it into here . It’s been recommended I use RTA,s and not sure what they are , and also it would be better for me to use bigger atomiser,s . When I started vaping I was looking for something that tasted and had the hit of a strong cigar ,and many companies advertised “ cigar flavours “ but were cr#p then I found TW heavy cigar 36mg and loved it. Then it became illegal so had to change to 18mg , big shock no taste ,so changed to 0.5 and more power and ok again .i found for whatever reason the heavy cigar flavour is very susceptible to the slightest change . But now I cannot get supplies from uk anymore because of uk post office rules regarding Covid so they say so been chasing around Thailand for something worth vaping . So if you recommend to me different tanks and atomisers it has to be A available in Thailand and B copes with plain tobacco flavour . I don’t like sweet and funny flavours . All I want is something that tastes like a cigar ( Dutch not Cuban ) . As an example heavy cigar with a 0.5 tastes great , with a 1.2 no taste at all . Thanks everybody I’ve had such good response from this forum and learnt a lot already .  

Bear with me all as I have to be a bit verbose.

I have a boxer bf mod I have numerous Rda I am vaping mtl a juice I’ve been vaping 5+ years.
I didn’t use my boxer or any rda for a while. When I did a rebuild as usual I noticed a “bad” flavour. Like most of you I went through a series of steps to no avail

I changed atomisers did a new build and soaked (vinegar, then retainer brite, baking soda and ultimately boiled) the other one I confirmed if I drip the juice tastes as expected I changed bottles and soaked (like above) the bottle I took apart the boxer and soaked the 510 (as above)
Obviously these cleanings weren’t all at once. I tried vinegar. Then when that failed I tried retainer brite (great to remove discolouration but leaves a slightly mint flavour for a few draws),when that didn’t work I tried boiling.

At this point I’m starting to wonder if something is going on with the way the mod is activating. The only thing left I can think of is that for some reason (and I’m not sure why it would have developed) when the metal bar contacts the ring on the 510/feeding tube area there’s some kind of charge that’s happening and raining juice or melting plastic (which I don’t see). Either that or there is some mould or something deep in the 510 assembly.

Have any of you ever experienced this kind of flavour terrible all of a sudden? I have now tried 4 bottles with four tubes. I have cleaned every element at least five times. I have confirmed I’m not just tasting it wrong by dripping.

it’s clearly not the atomiser or build related. I have a hard time believing it’s bottle related after what I’ve done to them.

I just cannot figure this out. The next step of course is going to be to try and use the same bottles /atomiser on another mod but I thought I’d ping you all to see what your thoughts are - because in ten years of vaping I haven’t experienced this, and troubleshooting has taken hours so far.

Just a few final points
no shorting Very minor sparks as you’d expect from this mod and the way it makes contact at an angle Been vaping a very long time and building since almost day one The rda’s are authentic, stainless etc I’ve tried 3 of them at least It’s not wire or cotton
I’m stumped. Appreciate any thoughts.  

So i'm not familiar with every single atomizer on the market. They're all different in their design. One potential problem i do believe to be universal in all these devices though is an "Airlock".

Regardless of how much cotton wool has been crammed into the wells of an RTA, or whether you primed your drop in coil enough, an airlock will prevent the e liquid from getting to the wick everytime. Time and time again you either re-wick or swap out the drop in coil. Then you think "there is definitely something wrong with the atomizer".

How many times have you built a new coil, or simply re-fiiled on an existing wick, and then found all you get is dry hits and you can't figure out why ?. Maybe you eventually decide "this atomizer is no good".

The simple solution is to add more e liquid than you think you should when "priming" the coil/wick. It's not a process which takes just a minute or two. The whole idea is to let the e liquid soak right through the cotton wool, through the channels until it starts to seep out the other end of those channels, where ever that might be !. To go from a tank to a coil/wick the e liquid has to travel through the channels.

If cotton wool soaked in e liquid is at one end of the channels then that is what is causing the "airlock".

Simply put "it's "trapping" the air in the channels and causing an airlock".

You get rid of all the air in the channels by "bleeding" the system. This should be the most important part of "priming". Allowing the e liquid you've added as a primer to expel all the air from the system. Without doing this you are running the risk of successive dry hits and confusion.

So you add e liquid as a primer, let it soak into the cotton wool then add a few drops more. Then, wait a few minutes to see how far the e liquid has got. Wait for it to come out the other end because that what you should be looking for. Once you see it coming out the other end of the channels you know the system has been fully bled. And then you can reassemble your device and fill the tank.

 

“I’ll NOT be doing THAT again!” - the famous Taurus War Cry was heard in our house this morning!

As happens to the aged, O500 hrs this morning found me suddenly wide awake for no good reason. As usual when this happens I got up, sat in my recliner office chair, drank a pot of tea, read for a bit, and visited forums until the rest of the world came awake accompanying all that with a vape.

However that vaping ( OK chain vaping for 2-3 hours ) was done with my new Feedlink Squonk, inadvertently loaded with 18 strength liquid, fired at 4.2 volts to begin with, through a 0.6 ohm coil.

Not good. Not good at all.

Having smoked since I was very young, inhaled even pipe tobacco etc I never reckoned I could get nic sic at this late stage … but OMG suddenly I got hit with the full repertoire, the sweats, the feeling of nausea, dizziness the restlessness where I couldn’t settle but had to prowl, the racing heart etc etc.

How did I manage to do it? Carelessness coupled with the old “it’ll never happen to me” routine basically.

I had grabbed a bottle of my old 18 strength Menthol Liquid, filled the squonk bottle without looking at the juice bottle’s label and chain vaped using what is in essence a protected mech mod with a new battery on a sub ohm coil.

I’m normally a tootle puffer with 1,6 ohm coils but OMG initially at least with the squonk I enjoyed trying DTL and blowing clouds … initially!

I’m sure the rest of you reading this will have more sense than to do anything like I did this morning, but trust me - I’ll NOT be doing THAT again!  

I’m a mouth to lung vapor and currently using the holic rda and galaxies rdta. I’ve tried using ni80 round wire and superfine mtl fused Clapton ni80 wire. The round wire is so easy to work with and the superfine is harder but I’m getting the hang of it. My question is with coils that ohm out the same with each wire I get flat flavor with the round wire and the flavor definitely pops with the fused Clapton wire. Is this normal? Same juice, same wattage, same ohms and same rda and squonk.
I love working with the round wire but not worth it if I can’t get better flavor.  

After taking onboard what everybody told me about not using a 50mg nic salt with a 0.5 coil I switched to 25mg nic salt . I got some new 1.2 coils , it took 3 weeks to get from England , and I don’t like them at all, it completely changes the taste . So back to the 0.5 . So I tried cutting the liquid by 25% with PG ,and it’s ok but not wow . Then I tried mixing the 25 mg salt with 3mg freebase and again it’s ok but not wow . I have used 18 mg liquid with the 0.5 atomiser for yrs so how bad is it using the 25 mg nic salt with the 0.5 coil because that’s the one that I really like .and I don’t feel drunk I feel fine . Thanks John  

Hey guys,
Just wanna drop in and say I ordered a Lemo2 to try my hand at rebuilding. It come with a coil and wick at .5ohm already in place. This thing really works awesome... tons of flavor and vapor and can even MtL hit if I dial down the air almost all the way. I do have two hopefully easy questions I'm sure someone knows the answer to...
How high of wattage can you push these or any handmade coil to? Also when you wick a new one, since it doesn't come with much info on it, how do you know if you're putting too much cotton in, and is there a trick to get the cotton right where it needs to be in that little wicking channel from the tank to where the coil is so the juice gets absorbed quickly and properly but without flooding it?
TIA and I know I'm know pro sub-ohmer by any means lol but for someone thinking about one this tank really works awesome.  

First off, I would like to say that I’m very new to vaping. I started off with a JUUL, then a Smok Novo 2, and eventually got sick of buying pods.

Now I have a Hellvape MD, and an Ares 2 - the first provides better flavor, but it’s still not comparable to what I was getting in my pod systems. I just recently purchased a BP Mods Pioneer, and I’m hoping that gives me better results. I’m using an Aegis Mini for a mod.

I’m trying to figure out what I’m doing wrong, because it’s really frustrating to spend all this money for worse flavor, when I was hoping it would let me save money.

I have about 40 bottles of salt nic flavors that are 50 or 35 mg, and a couple 3mg freebase I bought (120ml for $7 seemed like a steal). I would really like to get away from the salt nic, but I seem to get even worse flavor from the 3mg.

I’m using 2.5ID 28ga SS316L round wire from Master Wire Supply (I have a spool) with Puffs Organic Cotton. My coils are usually .7ohms, but I’ve tried up to 1ohm. I’ve also tried 1 ohm Vandy Vape Superfine MTL fused claptons, and experienced similar results.

I’m using the MD with the most restrictive airflow settings (3 small hole airflow disk), low (2-3) adjustable AFC setting. I have my coil as low as possible to the airflow, and I have thinned / fluffed my wicks.

I haven’t tried adjusting the airflow below the coil on the Ares 2, because the video instructions say wide open airflow below the coil is the best for flavor (I have found the opposite to be true for the MD).

Can someone provide me more insight?

Will 2mm ID coils with the same amount of wraps taste better than 2.5? Do coil ohms do anything for flavor, or does it only change how fast it heats up? Will I lose flavor if my coils hang outside the diameter of the airflow disk?
Is there a certain type of coil that would give me better flavor than regular round wire?

I use TC at 420F 20 watts


Any kind of feedback is appreciated and if I left anything out or you have questions about my set up that could help me out please ask! I’m at a loss on what to do, and it seems like no amount of research is helping  

Greetings from TX, fellow vapers!

I’m pretty sure this question has been asked before, and I apologize beforehand if it has.

We all know about the proposed flavor ban, that’s a given. And it’s not a matter of ‘IF’, but more a matter of ‘WHEN’.

Sales of flavors will become illegal, but what about usage? If I’m vaping in public, will I be subjected to prosecution for ‘Possession of a banned Substance’, or is the ban restricted to sales only?

I’m so thoroughly dismayed and disgusted with the lawmakers and news media. I can’t trust anything that they say anymore.