Well this sucks, I have an iStick 30w and toptank mini, I ran out of pre made coils so I thought i would try the RBA of the toptank. At first it read out as “protection” upon trying to fire it (I think the ohms were too low on the pre made coils included with the RBA at .1), then it said low battery (it was almost fully charged) so i plugged it in and tried to fire it once more and the thing started smoking (no protection message this time, just a little puff of smoke within the LED window). I only fired the button for a split second and it still seems to be functioning. Not sure what I should do lol or just ditch out on it? It appears to be working yet but stinks like an electrical fire now. I’m kinda reluctant to use it (I still have an old coil but it was starting to taste funky). Any advice or idea what might’ve happened?
I got a problem with my Luxotic Surface. I'm using a LG Choco Battery 18650, it was fully charged and when I press the fire button suddenly it appears for Battery Low even the battery was on fully charged. I tried my spare battery maybe its just a mistake putting a fully charge battery, but it was the same issue also with the spare battery. I tried the 2 batteries with my Geek Vape Aegis 100W to check whether my batteries are already broke but it works fine. I was vaping for my Luxotic Surface by 55.0 Wattage, 0.21 ohms, 3.40 Voltage. Can someone help me out to fix this problem?
It's an Innokin Endura T18 II. I bought it just a week ago. Everything was working fine until this morning when I tried to fire it and it just blinked three times. I thought maybe there was a problem with the coil, so I put a new one in. It was still blinking. So I made extra sure the coil was in properly. Then it started working again. I vaped for about an hour and then it started blinking again and wouldn't fire. Any idea what the problem is?
A friend of mine has just bought a Kbox and a brand new sammsung inr battery.
When the battery is fully charged it will only fire at 20w with a .5ohm coil. and when it gets to about 50% charge it will only fire at 8w!!
Is this normal??
Right now I have a few box mods, the IPv3, SIG 150w and the Snow wolf 200w. I'm using the Snow wolf 200w and honestly I'm not happy with it. I've had the button stick a few times causing it to auto fire and I'm noticing an almost one second delay from when I hit the fire button to when an actual vape starts to kick in (very slow fire up time, and I'm only running dual twisted 26g) on top of that I really dislike that I have to hit the fire button to see how much volts I'm using. I know the SX M class is one of the best out right now, but the fact it's a single battery concerns me because I typically vape between .12-.20 ohms and usually 60-80w (but since getting the derringer it's been 60). I really like the hot, dense flavorful vapes and I wanna make sure if I get the SX M class it'll be able to deliver that.
I just got my new istick 20w and I'm having some problems. I'm really new to vw mods I've been strictly mech for over a year. so I put on my kayfun with a 1.4 ohm build and it maxes out at 12w any higher and I get a protection message. I put on my patriot at 1ohm and it won't fire at all. I cant figure out why it won't go any higher.
OK so I got an aspire nautilus mini for free today (my close friend upgraded and gave it to me) and I was using it on my Istick 20 watt for a couple hours and then out of no where it started saying no atomizer and it wasn't firing at all and the Istick wasn't even reading the ohms it just says 0.0 it so I put it on a Itaste VV and it wont fire on that either I have no idea what to do?
hi my smok 22 vape pen button is jammed in so the top bit is fully pushing in and the bottom is fully not pushed in. it’s not firing or anything when i don’t want it to so that’s good but it also won’t fire at all. idk how to add images
I accidentally locked the up and down buttons by pressing both of them simultaneously for 2 seconds, I have tried unlocking them by doing the same thing like the instruction manual calls for. It doesn’t work, no “unlock” pops up or anything. You can hold them as long as you like and...nothing.
I have since figured something might be wrong with it as I am almost positive I’m doing it correctly. Now I have tried getting the reset button to work in hopes of the up and down buttons being unlocked upon reset. I hold the reset button for 5 seconds and I’ve tried the method of the combo with the fire button and reset as well as the up arrow and reset and the screen goes blank and turns back on but never says reset and the settings are still the same as before.
My next idea is plugging it into my computer in hopes of an update fixing this but other than that I am out of ideas. The device is stuck on 20 watts which is too high for the cartridge I’ve got on it. Does anybody have any ideas, please help me out.
So I pulled the trigger and decided to upgrade my istick 20w and get the istick 50w.
Came fully charged so threw on my nautilus and started vaping and I have to draw really hard to get some vapor. I've tried different wattages from 7-18 and the results are still low vapor. Not no vapor but not as much as I should be getting. So I thought it was a bad coil or atty so I threw the same tank onto my istick 20w and worked perfectly with a ton of vapor.
Threw it back on the 50 and made sure the counter was counting and took a vape for 7 seconds with about half the vapor from the 20w.
Am I doing something wrong?
thanks
Brian
Hello everyone I recently purchased an ipv mini v2 and I love it, it is working perfect. I only have one complaint the fire button rattles like crazy and it drives me nuts. To some it's not a big deal but I just don't like it. So do any of you out there know if there is a way for me to fix this? Once again everything else is perfect ohms and all that it's just the fire button. The wattage up and down buttons are supper tight and clicky. Any help would be greatly appreciated. Thanks