Washed The Coil?

I’ve been away from vaping for about 7 yrs. I don’t have any of my old equipment, which now I miss very much. I’ve been trying to get back to vaping for health reasons, and having to learn all over again. Everything is dual coil. I NEVER used dual coil, but I’m trying to learn. I got a Vaporesso PM40, a Drag S a hcigar vt inbox and a POS squonker that I’m using for a dripper (reviews said they leak and short out causing me to fire by their self. I joy cappo squonk box).
Do I figure dual coil watts and amps like I did my single coil builds. I never got into the low sub-ohm thing. Maybe 0.9-1 ohm.
It’s good to be back in ECF again.  

I’m curious as to why you shouldn’t do DL when using nic salts. I’ve got an Aegis Hero with a 0.6 coil at 15 watts. Even with the airflow closed off, it’s still to loose for a MTL. I keep reading and hearing I shouldn’t use nic salts for DL. The worst thing I’ve experienced so far is a mild headache. The nic salt is a 30mg.
Thanks in advance. ECF is my only true support group and I’m having a really hard time not smoking the stinkiest. Been back to vaping for about a month, and keep telling myself it’s all about baby steps. Not how many I smoke but how many I don’t smoke. I’ve got to quit for health reasons.  

I change my coil infrequently,I notice sometimes when I rewick or change flavour on my rta,my coil looked black and gunk.After I rebuilt it and used it,the favour is ok and no dry hit, just a little less flavour.Recently,there is people contracting Vape related illnesses and a few died.I just don’t have too much time recoil and built,as usually rebuilding my rta which is relatively new released would take around 20min and I don’t have the time.Is dry hitting dangerous for the health because of Formaldehyde of dry hit or is the risk low?
What’s actually risky vaping nicotine,PG/VG only?  

Calculated I spent 104USD on average for this three month,it’s some money due to me buying all the necessary mod and pod plus juice.

If my mod did not gave up on me I would spend 55USD on average per month,while using drop in coil which I am very happy about it...How much did you spent on vaping stuff and how much on average would you spent if you didn’t had to chip in on devices.

I didn’t do rta/rda because I had many working hours and I tried one rta,it’s just a hassle changing the cotton or coil and I am a lousy builder hence I use sub ohm tank  

Hello
I have the wotofo serpent rta top airflow single coil tank now and I just purchased the augvape druga rta. Flavor is 100% better in the augvape drugA rta but juice leaks out the bottom of the tank every time which is why I have to stay with top airflow as it never has leaked on me. So I’m looking for a top airflow rta single coil . I typically vape between 20-30watts so I don’t need a powerhouse. I just want the flavor and don’t care about clouds. Can anyone recommend the best top airflow rta? The wotofo serpent works well but it takes a hit on flavor. The serpent only has 2 small air holes around the coil area and I think this is why it isn’t producing a good vape. I was looking at the Zeus? Augvape intake of the dual one? Or any others anyone can recommend ?

primary goal: outstanding flavor
No leaking
Lots of air holes around the coil


thanks for your time  

Hey Guys,

I have been wanting to use a mech mod for quite some time now. But I didn’t want to rush into things, given that they can be dangerous if not used properly.

To prepare I have studied ohm’s law and have a pretty decent grasp on it. And have a calculator app on my phone.

I have checked out Mooch’s battery recommendations and have a good idea of what batteries to use and which to avoid.

I still do have a few questions I was hoping an experienced Mech user could help me answer:

- What would be the “sweet spot” as far as resistance and safety go for a dual coil set up? Obviously I want to go as low as possible and have a hard hitting vape. But I also want to be safe. I plan to use a dual 18650 Parallel mod (The Clutch X18). I would be most likely be using Sony Murata batteries as I cant find any Samsungs where i live. I’m thinking somewhere around 0.17-0.2? Or would it be safe to go lower than that? I will of course test my build on an ohm reader and regulated mod before throwing it on the mech to be safe.

- Are there any other general safety tips? Ive heard that you want to screw the Atty down all the way first, before inserting the batteries. And then insert the batteries. And when removing the batteries i heard you want to slightly unscrew the atty first, and then carefully remove the batteries? Can anyone please confirm if this is correct.

- Is its safe to chain vape on a dual 18650 parallel mod? When I say chain vape I mean like maybe taking 5-6 big hits back to back. Then waiting 3-5 minutes, dripping some juice and then doing another 5-6 hits.

- Is there anything I should be monitoring while I’m vaping? Like the heat of the batteries? From what I’ve read, the batteries drain quite fast on a mech. And after some experience you will just kind of know when they need charging because the vape experience changes. Is there anything I’m missing? Or something i should be looking out for?

- I can only vape in my kitchen. And sometimes there might be a little bit of water on the counter from someone’s drink sweating, or drops after someone washed their hands etc. Is this a risk? I will of course do my best to keep all surfaces dry. I’m not talking about large amounts of water or submerging or getting the mod really wet. But just what one might find on a kitchen counter.

- Any other tips you could throw my way would be great!

Thanks in advance!  

First off, I would like to say that I’m very new to vaping. I started off with a JUUL, then a Smok Novo 2, and eventually got sick of buying pods.

Now I have a Hellvape MD, and an Ares 2 - the first provides better flavor, but it’s still not comparable to what I was getting in my pod systems. I just recently purchased a BP Mods Pioneer, and I’m hoping that gives me better results. I’m using an Aegis Mini for a mod.

I’m trying to figure out what I’m doing wrong, because it’s really frustrating to spend all this money for worse flavor, when I was hoping it would let me save money.

I have about 40 bottles of salt nic flavors that are 50 or 35 mg, and a couple 3mg freebase I bought (120ml for $7 seemed like a steal). I would really like to get away from the salt nic, but I seem to get even worse flavor from the 3mg.

I’m using 2.5ID 28ga SS316L round wire from Master Wire Supply (I have a spool) with Puffs Organic Cotton. My coils are usually .7ohms, but I’ve tried up to 1ohm. I’ve also tried 1 ohm Vandy Vape Superfine MTL fused claptons, and experienced similar results.

I’m using the MD with the most restrictive airflow settings (3 small hole airflow disk), low (2-3) adjustable AFC setting. I have my coil as low as possible to the airflow, and I have thinned / fluffed my wicks.

I haven’t tried adjusting the airflow below the coil on the Ares 2, because the video instructions say wide open airflow below the coil is the best for flavor (I have found the opposite to be true for the MD).

Can someone provide me more insight?

Will 2mm ID coils with the same amount of wraps taste better than 2.5? Do coil ohms do anything for flavor, or does it only change how fast it heats up? Will I lose flavor if my coils hang outside the diameter of the airflow disk?
Is there a certain type of coil that would give me better flavor than regular round wire?

I use TC at 420F 20 watts


Any kind of feedback is appreciated and if I left anything out or you have questions about my set up that could help me out please ask! I’m at a loss on what to do, and it seems like no amount of research is helping  

After taking onboard what everybody told me about not using a 50mg nic salt with a 0.5 coil I switched to 25mg nic salt . I got some new 1.2 coils , it took 3 weeks to get from England , and I don’t like them at all, it completely changes the taste . So back to the 0.5 . So I tried cutting the liquid by 25% with PG ,and it’s ok but not wow . Then I tried mixing the 25 mg salt with 3mg freebase and again it’s ok but not wow . I have used 18 mg liquid with the 0.5 atomiser for yrs so how bad is it using the 25 mg nic salt with the 0.5 coil because that’s the one that I really like .and I don’t feel drunk I feel fine . Thanks John  

Dear forum!

here goes my strange experience:
I’ve been coiling and wicking for years pretty much the same way, and it was kinda ok = I adapted to all the quirks I had.

Recently I built a new coil, but instead of 4mm I decided to make 3.5mm coil. Same wraps number.
Wicked it as I alway do - exact same material, thickness (adjusted to coil diameter of cores) trimming etc.

And wow!
No problem with TC now!
Works reliably, no leakage, I can chain wape the whole tank!

could this one Change in coil diameter choice did the trick???

Or is it a fluke? (Well I’ll find out when I’ll built next coil same way...but still)

best regards
Vadim  

Hi,

I just tried to TC vaping - and it’s awesome!

it was harder to build the coil, took me couple of tries, but once I reached R of 1.3, everything started to work.
I used 26awg wire SS316L (that’s what they had ready in the store).
I have no dry hits - at all, it’s just perfect. It’s like having on the fly automatically adjusted curve!

I do have one small problem- 1 out of 10 mod firing - (almost) nothing happens.
is it a problem (not good chip/mod, wire, else?), or is it intended? (Coil overheated, wick is dry, else?). But that’s a small nuisance - I wait 10 seconds and wape again no problem.

what I still don’t understand - why I was always told at the stores “don’t TC vape - it’s the old way, now VW is the way to go” without any explanation.
So far I have a feeling that it was done exclusively in stores interest:
- because they know it’s harder to built, so they didn’t want to have a complaining customer “it does not work”, because the mods for tc probably cost more so it’s tougher sell, and they wanted to sell me more coils, wick, juice...

are there other reasons against TC? (Safety, medical reasons (idk - SS wire releases particles or something - seems unlikely (I know with Ti and Ni you should be causious)), else?

I continue to research this topic as well, online, YouTube, etc, but so far I found nothing against, except what I already mentioned (mainly it’s a bit harder to build the coils).

Would appreciate your opinions!

regards,
Vadim

ps. I use EHPRO Cold Steel 100 mod, Siren 2 MTL RTA.