Here are Two pics of a hybrid mod top cap I recently bought. As you can see, the positive tab on the battery is directly connected to your 510 pin or whatever it comes in contact with at the bottom of your atty.
Here is a pic of the 510 pin on the bottom of the Atlantis:
The pin simply pushes into a grommet and floats there. If the pin comes in contact with the side of the atty it will short the circuit and if left there will short the battery. Notice how close the pin is to the sides of the atty. If that grommet gets deformed in any way, that pin can touch those sidewalls and short the circuit. After screwing and unscrewing the atty on and off mods, that pin and grommet can move out of its centered position. On a hybrid mod if this atty is over tightened directly onto the positive tab of the battery, the pin can MASH down onto it, deform the grommet and touch the sidewall causing a short. Someone not aware of this with little experience has a ticking time bomb in their hands. Be safe out there.
Hello All, I have a question regarding the modification of an rda adjustable positive pin to work (better & safely) with a hybrid connection top on a new mech I purchased. The mod is not a true hybrid since it has the flush sitting 510 threaded top cap without a pin inside, allowing the atty to make direct contact with the battery.
My question is, can you take out the adjustable positive pin and put a kind of insulating "washer" between the pin and the negative threads to ensure the outer threads do not make contact with the positive terminal on the battery? I would also like to put a better, wider pin in that will make a better connection and not indent the positive terminal on the batt. Anyone have any advice for this?
What is currently the best atomizer flavor out there? Bar none. Doesnt matter what vape style it is. If someone wants to experience the best possible flavor an atty can produce, what is it?
Is it the newest and greatest Falcon 2, a Zenith, Zeus X, Dang rda, wotofo rda...? Or does an old classic still reign king?
What do you guys think? What atty is the measure for flavor?
Hey everyone. I got my triton today. Going to load up 2 geysers on it, as it is a dual atty, parallel battery mod. My question is this, does this setup draw individual powers from a dedicated battery to the atty atop it, or is the parallel power running both attys, in which case what should I know about building my rdas for this setup? Can I have 2 different resistences, 1 for each rda? I did see this in a video and thought why would anyone do that? Also, does this change the allowable resistence? I'm using 35A batteries (mxjo) so the math suggests .12 as the lowest safest res single battery. (I rarely dip below .3). And no i don't want to start a discussion on whether or not those are actually LG's lol. I'm aware of all that hubub. Thanks!
Sent from a cool but overpriced phone on TapaCrack at yo mama's house.
So I just got my Geekvape Zeus. When I try to use it I get a "short circuit" error. Does anyone know what this means or how to fix it? I tried screwing it in tighter and looser and nothing works.
Anyone know of any hybrid mech mods? (Direct atomizer to battery connection)
Due to a recent rash of vapers using mech mods without proper knowledge. here is a simple test for vapers who want to use unregulated devices, if you can confidently answer these questions, you just may be ready to take the plunge to a mech or unregulated box mod. If you cannot answer all of the questions, don't be discouraged, use the test as a base for the knowledge you may need to acquire.
1. Define ohms law using a short paragraph, and show the equation below.
2. Define watts law using a short paragraph, and show the equation below
3. Draw a simple open circuit.
4. Draw a simple closed circuit
5. Find the resistance of a circuit running at 3.9 volts with a 20 amp current
6. Find the voltage of a circuit running at .54 ohms with a 5 amp current.
7. Find the wattage of a 4.1 volt circuit at 2.3 ohms
8. You are wrapping a dual coil set up, while pinching your coil with metal tweezers you accidentally press the fire button,
the leg of the coil you are wrapping fires bright and then disintegrates, why has this happened?
9. Your mechanical mod is getting extremely hot, is making odd noises, and has an odd smell, what is happening
and what is the procedure in this situation?
10. What is the lowest safe resistance of a 4.2v lithium ion battery rated at 20 amps?
11. You have been using a battery for several hours now, and have noticed a sharp decline in vapor production,
why is this happening?
12. You wrap a coil that reads .42 ohms on your multimeter, what important factor should be remembered while using this coil?
13. You are using 2 stacked 18350 lithium ion batteries in your mod, what kind of circuit is this? what changes because of this?
what does not change?
Hello im looking for a RDA, I have had a shop around and I have narrowed it down to a few, the tobh atty, plume veil, magma and the dark horse dripper. I am more leaning towards the tobh atty as personally it looks the more simple to build on. I will be trying to build .5 ohm coils as that's what im using at the moment (aspire Atlantis) could you give me any advice/recommendations
So, here's the deal. My new mod was delivered today. I knew it had a fixed stainless 510 connector, but I wasn't worried. Anyway, I'm not sure what I am doing wrong, but the tank keeps coming loose on the mod. I know I am probably not cranking it down tight enough, but I am afraid of going too tight and screwing up the threads.
So, I am looking for an adaptor that has a spring loaded pin on both sides. Spring loaded on the battery side and spring loaded on the atty side. Is there such a thing? I would also prefer that this is 22mm wide. Any ideas?
So I recently purchased a Pulse X 90w. And I've noticed that the squonk bottle is leaking inside the mod itself. And sometimes juice gets pretty close to the positive battery contact. Does anyone know what may be causing this? Whenever I fill the bottle I always fill it up to about 3/4 so that there is displacement for the tube itself. I get it all screwed down and back in then after a while, or my next fill I notice that it's leaked again. This is becoming a rather annoying problem. And I'd rather not chuck a mod that I just bought because of a stupid issue such as this. Any suggestions would be greatly appreciated. Thank you!
When I hit the fire button on my box about 2 seconds in my atty pops sometimes a little and sometimes very loud. It scares the beegeebies out of me when its loud and I check to see if I have all my teeth. What causes this and how do I make it stop?