So no mine didn't melt haha but I was wondering what the best build would be for a plume so I could prevent this? I normally go with a .3 ohm build 24 gauge 7 wrap so yeah thanks guys!
So I can't figure out were to order an authentic plume veil, or what a good website to order one from, but Iv been hearing things were the machining on them has been very poor and that's not good, but if you guys have an opinion on the best clone they have that would be great too, but I do like authentics thanks guys!
Okay so not sure if this is the right section or not but its the only relevant place I could find. .
My first build was okay coils turned out fine but the wicking and position of the coils where terrible. So I decided to have another go.
Opinions appreciated.
Using smok xpro m80
Plume veil v1.5 clone
26gauge kanthal
Wrapped around a 2mil precision screwdriver.
8 or 9 wraps can't remember.
And reading at .46 ohms
P.s don't know why the coils look like there glowing purple but I promise their not haha.
Hello im looking for a RDA, I have had a shop around and I have narrowed it down to a few, the tobh atty, plume veil, magma and the dark horse dripper. I am more leaning towards the tobh atty as personally it looks the more simple to build on. I will be trying to build .5 ohm coils as that's what im using at the moment (aspire Atlantis) could you give me any advice/recommendations
Stopped into my local B&M a couple months back and noticed they had some Hcigar RDA clones, namely the Plume Veil. Thought that was cool and figured I would pick one up sooner or later. Today was that day so I stopped by to buy one. To my surprise, most of the Hcigar stuff no longer have etched logos, including the Plume Veil. Bought one anyways for the functionality.
I have other stuff such as the Hcigar Nemesis and Hammer. Part of their intrigue comes from the etched design artwork... I was kind of bummed.
On a side note, it's my first RDA. Wound a .8 ohm coil on my first attempt with a screwdriver. Not bad for a newbie, right?
Looking at the charts, I would like to keep what I do in the green zone. What I cannot find is a chart that goes low enough in ohms to tell whether or not what I am doing is okay. My latest atomizer build is a .4 ohm on a Plume Veil. I use it with max airflow, side windows open full and top cap open allowing air. Excellent vapor production (for me anyway), at 7 watt - 1.7V (IPV2X mod reading). So where do you think that type of build would land in the charts. Safe to say I am in the green zone? I guess maybe I have developed some paranoia with this formaldehyde thing that has been floating around the internet. Does anyone know where to find a chart or calculator that goes from .1 ohm on up and indicating the safe areas?
Thanks,
Charles
Hey guys. I have been in the vaping scene for a little while now. Just curious to what everyone likes to sub-ohm with.
My favorites so far.
Mutation X V3- 24 gauge dual parallel 5/6 wrap
Mutation X V4- 20 gauge dual 5/6 wrap or dual 6/7 wrap
Turbo RDA- both of the above builds work well
I've had the dark horse, doge and doge v2, freakshow, and a few other RDA's and the 3 above have been my favorite....v3 was my favorite for a while until I tried the v4, its now my favorite, and its a tie between the v3 and turbo for 2nd and 3rd place.
So I built a twisted build out of nichrome 60 wire and tried it on a triple series 18650 mechanical box and it melted the coils why won't nichrome work with any series boxes 8.4 volt melted 12.6 volt melted but I can build a .06 nichrome build and run it on my mech tube mod and it handles it I can build .15 and run it at 150 watts on my Sigelei and it handles it but bump up the voltage and it melts don't get it. I ran a .30 nichrome build at 260 watts on a SMY 260 and had no failure of the coil so I'm puzzled why a series mech box desemates the coils?
So here's my question. First I'll start with some background to hopefully avoid questions in the future. I've been vaping for about 3 months. I have a eleaf 30w, that I usually use a nautilus/ atlantis tank on. I also have a sigelei 150w, that I use a plume veil and dark horse on. So my question is that I really like the cool vape that I get with the eleaf on my tanks. I have been tinkering with the the 150 w/ the dark horse and I finally think I found a build that gives me that same feeling. I would like to know thoughts on if the M80 would assist me in accomplishing this further on my builds with the TC.
What is your go to single coil build in terms of gauge wire, diameter, and number of wraps : (no fancy Clapton or twisted build just a "regular" wrap)
And if you have a reason please include it: For example: "I'm a flavor junkie and this is best flavor build I've found" or "I like short ramp up times" etc ...
(I know preferences may vary greatly)
Thank you very much
:
Sent from my iPad using Tapatalk
If you had $450 to spend on vaping equipment, what would you buy?
Currently have an authentic Hana Modz V3 - Plume Veil - Little Boy - Tugboat V1- Kayfun Lite - Boss 26650
Vaping⚓Sailor