Tugboat V1

Last week I returned my tugboat box mod to Flawless in exchange for a new because of the slight paint coming off on the corners. Now its on its way back, is there anything I can add to the tugboat to prevent the paint to chip off or ware off? Anything? Any help would be appreciate it!  

Anyone know any websites that still the Tugboat Box Mod? I know they were limited but i didnt know they would of went that fast lol  

so in my pursuit of vaping above 200 Watts I made a fuse 3x24ga gauge wrapped with 36 gauge and I tried three coils. it came out .07 I Vaped it at about 375 watts it was a hot vape but the ohms were very low so I had a problem with power my DNA 250c was reporting 65 amp output so I took that and put in dual fuse 22ga gauge wrapped with 36 gauge I ran that build triple coil I used it at about 250 Watts. what I am trying to do is vape at about 300 to 400 watts with an ohm or .2 to .3. the inner diameter will be 5.5 or 5 mm I'll be using the kanthal core wrapped with 36 gauge and ni80.I'm trying to figure out what my next bill should be to try to vape above 300 watts the restrictions I have is it can't be below point 1 ohm or above .3 ohm I have two aromamizer plus has with the series deck The parallel deck a second parallel deck and a single coil deck. The single coil deck fit 6.36 mm.

I also have the aromamizer titan.

What gauge would you Clapton?

Sent from my HD1907 using Tapatalk  

Hi all and thanks in advance for all help.

I have

26ga + 32ga SSL
28ga + 32ga SSL

And for the life of me I can't workout how to get a coile wrapped at a decent ohms for a single coil to go in my aromamizer v2 single deck.

Can anyone help and suggest what's the best ohms to be using for single coil.

Thanks  

Just got this SX 350 mini M. It's been working beautifully sans a few issues that I am sure are user induced.

First off I will tell you that the Lemo 2 that came in at the same time is Freaking awesome. I have a Kanger Sub Lemo drop and now the Lemo 2. The Lemo 2 kicks *** I the airflow department. It's robust and easy as hell to fill. I put a 3mm coil in it and pancaked the wick. 9 wraps and it's coming in at .118 ohms. Awesome flavor production and nice thick vapor.

So I moved on to the Tugboat to see how Ni200 fairs in the RDA world on this particular device. I went bananas with my coil and ended up with this monstrosity.



I twisted two strands of 28g Ni200 together with a drill and wrapped it 17 times. It comes in at .06 ohms. Performance wise it takes a while to ramp up but when it does it produces thick vapor but towards the hot side. Another thing is that the drip too gets hot really quickly. I'm running it 50J and have the temp cut off at 425F. The hot drip tip is one of the issues I mentioned. I vaped this thing bone dry and didn't get any burnt taste.

Then I moved on to the Lemo drop. The manual had an interesting coil method reccomended so I decided to go for it.





This one I wrapped about 10 times on a 3mm driver. Stuffed a small amount of additional cotton down inside like the manual suggested. The problem is that it gets stupid hot (the drop tip) stupid fast. I'm running it at 17J because this one is coming in at .365 ohms.

Short story long the device itself is working great. I just need to find the sweet spot with this Ni200 coil wise. Any tips in that department would be greatly appreciated.

At the end of it all the LEMO 2 and the Mini M seem like they were made for one another.  

If you had $450 to spend on vaping equipment, what would you buy?

Currently have an authentic Hana Modz V3 - Plume Veil - Little Boy - Tugboat V1- Kayfun Lite - Boss 26650



Vaping⚓Sailor  

I am trying to get the best flavor with the best single coil build.

Objectives:
Flavor Smooth Vapor
Materials:
Kanthal Wire 35mg Nic Salts
I have noticed that either depending on the diameter of the coil or the spacing of the coil wraps You get a different kind of vape hit. It seems like higher gauge wire produces a smoother hit. And then couple that with a small diameter coil build, plus squishing the coil together to remove all coil spacing results in the smoothest possible vapor.

Can anyone confirm my findings? Or does anyone have any tips because I have still to replicate the smooth hit from clearomizer sub tank cartridge's that are non mesh. I am starting to think this is because the cotton is wrapped around the outside of the coil instead of being shoelace through the middle of the coil.  

What is your go to single coil build in terms of gauge wire, diameter, and number of wraps : (no fancy Clapton or twisted build just a "regular" wrap)

And if you have a reason please include it: For example: "I'm a flavor junkie and this is best flavor build I've found" or "I like short ramp up times" etc ...

(I know preferences may vary greatly)

Thank you very much

:


Sent from my iPad using Tapatalk  

I recently found a Tugboat Tuglyfe 200W box mod i'd bought (around 2017) but never used.

I tried to charge it up but it wont hold any charge.

Is there someway this could be done without taking it apart. I've had a look at the escribe software and cant find much help. Is there another method to kick start the battery?

Thanks
SK  

Just got my wraps for my three favorite mods in vapemail from Vapor Skins, and I was very impressed with the exact fit, quality, fit and finish of all three. I got a Carbon Fiber for my IPV Mini 70W, an Exotic Wood for the Sigelei 150, and a Textured Wood for the VS rDNA 40. I've attached a pic (pease ignore the messy Tugboat). We'll see how they hold up, but for now I'm a happy customer!