Kangertech Evod 2 Gurgling Issues

I don't know if anyone has issues with their protank 2 but I hear a lot more negative than positive on them. I was messing with one of those bootleg ones and I couldn't figure out why it kept on leaking. Now just yesterday a friend gave me his protank 2 and Im guessing it was because he was tired of it leaking. When I first took it apart I took all the pieces off and connected them all again one by one making sure it was air tight as I added each piece. Everything was air tight until I got to the coil. I was taking a drag off it and it immediately started leaking and I was like why the heck does it do that? I noticed that it was leaking from between the coil and atomizer where the two little airholes are. What I did to fix this was take an old coil and gently pull off the little silicone ring (above where it says the ohms and below the wick) then I dropped it into where the coil meets the atomizer. After I just screwed in my coil and it works perfectly. No leaking whats so ever! Very good cloud production so far I recommend trying this if you have one. Sorry if someone already wrote this but I did a lot of looking around and never found an answer. Also didnt know where to post this so I apologize if this is the wrong section.  

Hi guys need a bit of help here, I just installed that rba base while watching a few yt vids. With the coils that came with it, reading at 0.24ohm. I've pulsed it on 51W, checked for hot spots (as best as I could judging by wht I saw the guys did on yt), wicked it as best as I could. Primed the wicks. Screwed everything together, waited a couple of minutes. 70VG, 4.5mg juice. Started at 45W, few hits, went up to 65W, +5W at a time. Hard preheat.

Results: two of the smoke alarms in my flat went off but that's not the reason why I post lol

I might have overprimed the wicks. However, I'm halfway through the 3.5ml tank and the cracking and gurgling noises won't go away on the pull. Tried adjusting the airflow, changing the preheat to normal, turned the watts down to 55W. Gurgling and cracking remains. Vapor production is intense. Flavor ain't bad, however I think that the factory coil I used before gave a slightly better flavor. I get no spitbacks just the gurgling and cracking that I can't get rid off, so any advice welcome.

Another thing I noticed is the tank heating up a lot, mainly at 65W. Found that table and it shows that I can go from 43.7-73.5W with the 0.24ohm coil. So 65 ain't max.
https://i.pinimg.com/originals/6a/18/d9/6a18d946e8a2a912ca8d8778056af5de.jpg

Should I be concerned about that?  

I haven't been having much luck with the two egrips I ordered. The first had broken plastic on the inside (little bits of plastic were caught in the threads, and had probably fallen into the tank). Number one is on its way back to the vendor.

On number 2, the atomizer base won't sit flush with the bottom of the device, and I think it's causing all the gurgling and leaking (e juice was also leaking out of the bottom of the device). I tried taking off the atomizer head and reseating it, and that didn't work. I'm hoping a new base might fix this problem. Any ideas?

Both devices are brand new. When I ordered the first one, I wasn't aware that it was available in a wood finish, so I ordered the second one.  

I just burned through my first coil on my KangerTech Evod 2, and I started wondering if there was anyway to extend the life of a coil. Do big hits, or small hits make a considerable difference? Just wondering because ultimately it can either reduce or increase the overall cost of vaping.  

I've been using disposable clearomizers since I started vaping, with an 808 kit, and that's been working fine for me, but I came across a super cheap deal recently for a Kanger Evod starter kit, so I bought one. I paid about $14, so it was a no brainer.

The tanks have these disposable coils, but the tanks seem like that they can be re-used forever, as long as they don't crack or fall on the ground and break, is that correct?

I saw that they sell a glass tank for it also, so I think that I'm going to pick one of those up, and I'll be able to vape on any juice that I please, without the fear of the tank cracking, and I'm assuming that that tank will last for a very long time.

So far I'm pretty happy with the Kanger Evod, and I like the vape from it.  

I have my Aspire Nautilus on my iTaste MVP 2.0 at 11 watts, running a 1.6ohm coil. I have also used it on my Nemesis mech mod with either an LG HE2 or a Sony VTC5 (I already know that mech's aren't ideal for tanks, but it was working really great). Everything has been fine, but now I'm noticing a bit of gurgling. Am I just under-powering the coil?  

I got EVOD battery and aspire charger.

Specs of EVOD charger has 400mA output and aspire charger 420mA output. It's the only difference

Can I charge EVOD battery with Aspire charger safely?

My EVOD charger is an hour away.  

Hi

I recently purchased the eleaf istick which I use with the kangertech subtank.

While I am impressed with the vapour production, I find it way too harsh and hot. On the coil it has the recommonded setting printed between 15 - 30w. I'm at 15w, but I'm still finding it too hot and harsh.

My question is:

is it safe to go down all the way to 11w or even possibly 8. I am confused as I've heard this could short my device or cause injury e.g device exploding, fire...

Thanks  

Hi all,

I've been vaping for around 9 months, and I'm new to this forum (as you can see on the left haha.) Anyways, due to recent money issues, I've had to ditch my Atlantis 2 and go to a Subtank Mini. I enjoy it a lot, except for one issue...too many dry hits!! Especially when I'm using it at 30 watts on a box. Does anyone have any suggestions as to how this can be fixed or minimized?

Thanks in advance!  

righto heres the story. started out with those ridiculous ecigs that looked like a ciggerette. but has the red light for a tip. Got it from our Neighboring country. next i found someone and got a Innokin itaste V3 and a ****ty tank. it was the budget kangertech tanks which has many problems.

after browsing around i decided to check out the ELEAF ISTICK 30W with a kangertech subtank nano.
What do u guys think of this combo?! also what box mods and tank combinations would u highly recommend? so spoiled for choices here!~ Feel free to share your experiences of your first devices! The more we learn the more better!

Yours sincerely.
Vaper from a FINE country.