I have a new istick 30w that I use with a smok micro adc2. I've used it with a new 2 ohm coil at 8 watts and is great. I changed to a used coil I had cleaned and things got weird. It's a 2 ohm coil and the istick is reading it at 4.9! At 8 watts the throat hit was too much so I went down to 6 watts. According to the manual the istick doesn't even fire to 4.9 ohms. So let's see what you got?
Hello Been vaping about 2 years now
My setups are Vaporshark Rdna 30 Istick 30 watt and a provari 2.5 and a IPv mini v2 30 watt
So like many others I have been juggling with wattage I currently Use A couple of kanger subtank minis using the RBA and a kayfun v4 I've been all over the place building ohms but have settled on 1.2 - 1.4 ohms BTW I'm not into sub ohms
So after many months of different ohms and watts with the help of steam engine I have found I like my vape at a heat flux of around 175 so to get to this and I can't believe how simple it was I just take the ohms I am using such as 1.2 @ 12 watts = 178 heat flux 1.3 @ 13 watts = 178 heat flux and so on I can't believe it became that simple
So I suppose all it takes is to find what heat flux you enjoy and adjust from there
I never bought that what I have read thru the last 2 years that 14 watts is 14 watts no matter what ohms you use it seems to me there had to be more factors involved
Just my thoughts
Sent from my iPhone using Tapatalk
So I decided to try a 1,6 ohm coil on kayfun v4 clone Tobecco and I am using 28gauge Kanthal with a cotton
wick on a Rdna 30 and its vaping well at 15 watts I have a kanger subtank mini coming in the mail and here goes my question
So the kanger subtank states that with a .5 ohm coil i could vape up to 30 watts but the voltage comes in at like 3.8 volts
I was under the impression that the rdna 30 needs at least 4 volts to work which kinda brings me to my second question
What is the point of of sub ohms? cant i just build a 2.0 ohm coil or something like that to achieve the results as if i was subohming
I am very confused on this
thanks for the replys in advance
Oh yea is a 1.6 ohm coil at 15 watts a normal build or any recommendations for the kayfun v4 for watts and ohms thanks again
Hey everyone,
I've been vaping for about two years now, and have decided to start dripping. For the last few weeks, I have been dripping on an IGO-W, 26G Kanthal single coil (7 wrap micro coil reading at 0.8ohms) on my iStick 30w.
I just recently purchased a new battery that should arrive today, and was wondering if anyone had advice/tips on producing some fat clouds! Dual Coils? Different coil builds? Number of wraps? Watts to vape at? I think you get the picture lol.
The items I will be using are as follows:
-SMOK XPRO M80 Plus
-IGO-W
-26 Gauge Kanthal Wire
-Japanese Organic Cotton
- 80vg/20pg Juices
All input is greatly appreciated. Thanks!
-Tyler
Somehow, I inadvertently pushed the buttons just wrong today and it went from 7 watts (my usual power setting) to 50 watts (the highest setting). I didn't even mean to push any of those buttons.
I experienced instant burnout and a horrible taste in my mouth and the coil was instantly ruined.
Do people really vape at such high power? If so, how often do you have to replace the coil? And how many ohms are you putting that through? The coil I replaced it with is 1.77 ohms which is about the same as the one I burned out.
50 watts seems so excessive to me that I double-checked and yes, that's what it says it goes up to. Even at 7.5 watts the coils seem to burn out too fast which is why I vape at 7.
I feel like Nigel Tufnel designed this thing. "But it goes to 50. That's 43 higher than 7. So it's like 43 more. So when you're vaping at 7 watts and you want that extra push over the cliff..."
(I'm actually impressed that Nigel could do the math to figure that 50 was 43 higher than 7)
a few little questions. I actually like dripping my 3 mg nic in max better even than vaping. I drip using 3 mg nic on a Istick 50 watt set about 23 watts with a draw of about 2.5 seconds and the coils reading says 1.6 ohms and the air holes blocked a tad on the el diablo bael. I vape on the Istick 20 watts somewhere around 7 to 8 watts on factory coil of 1.8 in a nautilaus mini
my questions: 1) does sub ohm in a rebuildable tank give flavour similar to a dripper
drippers seem to require higher watts is this in anyway suggested as less healthy ( I am not too concerned about the increased supposed formaldehyde issue I believe Dr F had issue with the research and in my opinion I probably breathe more formaldehyde off gassing wandering around carpets and insulation and pressboard)
2) the nic level is quite a bit lower in the dripper Does this actually translate to a drop in nicotine/contine levels in my blood in other words would I need to drip more to keep my nic levels somewhat reasonable re setting off " the I want a smoke brain run"
3 if I were to drip only for 3 or 4 days am I likely to find my 12 mg vape to strong
thanks for any insight you might provide
I've been using only twin-18650 mods for some time, and before the shipping ban came into effect, I bought a backup of my most-used mod (a Geekvape Aegis X), but since the 100W single 21700 / 18650 Voopoo Drag X Plus was only $35, I also picked up one of them as another backup.
I vape exclusively on RDA's, typically with a 3mm dual coil twisted build with 24 or 26 gauge Kanthal or nichrome-80. 5 or 6 wraps with 24 gauge, 6-8 wraps with 26 gauge. I typically vape these between 90 and 110 watts.
I did not expect to get a 'true' 90-100 watts out of the Drag X, so I set a target of around 60 watts. I mounted a 3mm dual coil twisted 28 gauge build with 6 wraps, which on my Aegis X vapes great at 60 watts, and very good at 50 watts. It measures at 0.45 ohms.
But on the Drag at 60 watts, it only vapes at what feels like 30 watts on my Aegis. Setting it higher makes no difference either, it seems to 'top out' at ~30 watts regardless of the setting. 60 watts @ 0.45 ohms is only around 11 amps, so I doubt I'm hitting an amperage limit.
I am using 18650 batteries (VTC5A), and it is about time to replace them, as I am only getting around 70% the battery life as I did when new. I will be picking up some 21700 batteries at the same time, which hopefully help with things on the Voopoo.
Does anybody have any good experiences with ~60 watt builds on a Drag X Plus?
Ok I upgraded from an evod 2 to an Istick 50 with the lemo ll today and built my first coil and wick coil came out at 1.9 ohms and I'm using organic japanese cotton been vaping on it for a few hours now and I'm getting a sore throat never got a sore throat from the evod 2 any ideas why this is happening?
I have the Smok xPro M80 plus and I have a couple Kanger subtank minis I use with it. I usually use .5 ohm coils. Sometimes it will show the ohms fairly correctly at .54 or even .61, which seems close enough. However, as I puff, the ohms reading will tend to change after every few puffs. Sometimes it will even say up to 1.5 or 2.0 ohms on the same tank coil! One tank seems to do it worse than the other, but the two I use now both will change quite often, and once in awhile quite drastically. It sometimes helps if I unscrew the tank and screw it back on, but if it isn't really tight, the ohms read are really far off from what they should be. I'm not sure if it is the tanks or the M80 plus that has the problem. When it reads really high, if I don't catch it before I take a puff, it is horrible and burny-dry, since it thinks the ohms are so high...
Has anyone else had this problem and/or have any ideas as to how it can be fixed??
By the way, I've cleaned the connections and everything thoroughly, so it's not that...
so in my pursuit of vaping above 200 Watts I made a fuse 3x24ga gauge wrapped with 36 gauge and I tried three coils. it came out .07 I Vaped it at about 375 watts it was a hot vape but the ohms were very low so I had a problem with power my DNA 250c was reporting 65 amp output so I took that and put in dual fuse 22ga gauge wrapped with 36 gauge I ran that build triple coil I used it at about 250 Watts. what I am trying to do is vape at about 300 to 400 watts with an ohm or .2 to .3. the inner diameter will be 5.5 or 5 mm I'll be using the kanthal core wrapped with 36 gauge and ni80.I'm trying to figure out what my next bill should be to try to vape above 300 watts the restrictions I have is it can't be below point 1 ohm or above .3 ohm I have two aromamizer plus has with the series deck The parallel deck a second parallel deck and a single coil deck. The single coil deck fit 6.36 mm.
I also have the aromamizer titan.
What gauge would you Clapton?
Sent from my HD1907 using Tapatalk
I just got my new petri RDA and put the coils on that came with it. Installed it properly as far as i know. I dont have an ohm tester however and when i plug the Petri onto my 20W eleaf istick (to try and see if it would come up with an ohm reading) it just said 0.0 ohms.
Is this just because the istick is 20w and cant handle subohm builds?
How do i go about testing the ohms without an ohm reader