$450 What Would You Buy?

For all you brainiacs and problem solvers out there. I've just recieved my Hcigar DNA 50 Hana Modz Clone from our friends at Fasttech. Overall it seems like a niece piece for the price. I've only really one issues with it which is as follows. The voltage read out is fairly accurate up to 40w but can't seem to go higher than 6.4v all the way up to 50w. 50w should read at 7.07v given the below build.

I'm currently using purple efest 3100mah batts with a 1ohm dual coil on a plume veil.

Is it that the display is faulty, (doubt this), I need higher drain batts (probably not as not pushing the amp limit here), or simply just that it's a clone and the chip isn't all the way up to the job?

I'm leaning towards the last one but can't complain, as an (essentially) 40w mod for the price is pretty flippin good!

Any ideas or suggestions would be great.

Cheers folks!  

So I can't figure out were to order an authentic plume veil, or what a good website to order one from, but Iv been hearing things were the machining on them has been very poor and that's not good, but if you guys have an opinion on the best clone they have that would be great too, but I do like authentics thanks guys!  

To all the mouth to lung (Tootle Puffers) here ... There was a time when the famous "Kayfun Lite-Plus V2" was the gold standard when it came to single coil / higher ohm / low amp Tootle Puffing.

Now that this atomizer (to include all the Chinese clones of it) are so very hard to come by (to include spare parts), has anyone here replaced there old Kayfun Lites with the new "Kayfun Lite 2019" atomizer ?

I just ordered a couple of Chinese clones of the Kayfun Lite 2019 so I can make the big changeover.

Good bye to the sweet Kayfun Lite-Plus V2
Almost 6 years vaping on this
Rest in Peace ....

 

Hello, just wondering if anyone owns or knows anyone who has a Hana Modz Dna30 with S.i? I wanted to buy one but wanna know if anyone knows how bad are are they? Thanks to all responses.  

I just bought an eleaf istick. I was using, for the few months I've been vaping, only eGo type batteries and decided to spend a little more on a mod and an RTA (EHPro kayfun lite).
The istick just arrived. I know it's not the most advanced piece of vaping hardware, but it's a huge step up from the eGo c twist.
I mean, with the same clearo (nautilus mini), the same juices and, allegedly, the same voltage, this thing makes my vaping experience so much better it's almost unbelievable.
If you're using an eGo battery, and you're serious about going on vaping and quiting smoking for good, by all means buy a regulated mod. It's really, really better.
I realize in the U.S. it's not a big deal, you can get a mod by $30 or less, but here in Brazil an istick goes for at least $100,but it's worth the money.

Now I expect the kayfun to be another step up, after I get decent coil building and wicking skills.

Just sharing the experience anyways.

Thanks for all the help you at this forum give to us at the community.

Cheers!  

I'm building a dual parallel 26g, on a 2.4mm screwdriver 5 wraps in the mutation x v3. Everything looks fine, one coil looks better than the other but still fuctional. I pre fire the coils to make them glow from inside out and they do. I put it on the hana mod and it reads out "shorted". I currently dont have a ohm reader which I should have gotten one long time ago before sub ohming but I depends on the box mods. Anyways anyone have any clue what might be or is the hana trippin? I get hot button on the smpl mod clone but I'm guessing its cus I was ore firing to get it to burn right (without cotton)  

So no mine didn't melt haha but I was wondering what the best build would be for a plume so I could prevent this? I normally go with a .3 ohm build 24 gauge 7 wrap so yeah thanks guys!  

Just as the title says..just bought a kayfun lite +/ Russian 91% clone, and the drip tip gets hot after a few hits..using mvp 2.0 that only goes to 11 w ( which is where I usually vape) with 1.7 coil/cotton wick..should I just look into another drip tip made of a different material? This is my first rta..my protank 2 tip never got hot even when chain vaping..the tank would warm up pretty good, but never the drip tip.  

A friend of a friend has for sale his Hana Modz V3 (DNA 30 I believe) and a derringer RDA and he is asking $85. The batteries are dead in the Hana so assume I'll have to come out of pocket another $15 for that, is that a fair price?  

Sorry guys, I wasn't sure exactly where to post this, it could fit into at least 4 different forums so if this isn't the best one please move it to the correct forum.

As the title states, does anyone have a P3 Titanium + Kayfun v4 and can share a picture? I'm just trying to get a sense of how the Ti looks compared to the SS used on a lot of tanks, specifically the Kayfun v4. Also, a picture with the P3 Titanium + Squape-R would be great as well.

Not to be picky or anything but I would really prefer authentic versions over clones as I plan to buy the authentic versions.

Thanks everyone, it's much appreciated!