I Am Stumped On This Kanger Subtank Rba Deck Problem...

so in my pursuit of vaping above 200 Watts I made a fuse 3x24ga gauge wrapped with 36 gauge and I tried three coils. it came out .07 I Vaped it at about 375 watts it was a hot vape but the ohms were very low so I had a problem with power my DNA 250c was reporting 65 amp output so I took that and put in dual fuse 22ga gauge wrapped with 36 gauge I ran that build triple coil I used it at about 250 Watts. what I am trying to do is vape at about 300 to 400 watts with an ohm or .2 to .3. the inner diameter will be 5.5 or 5 mm I'll be using the kanthal core wrapped with 36 gauge and ni80.I'm trying to figure out what my next bill should be to try to vape above 300 watts the restrictions I have is it can't be below point 1 ohm or above .3 ohm I have two aromamizer plus has with the series deck The parallel deck a second parallel deck and a single coil deck. The single coil deck fit 6.36 mm.

I also have the aromamizer titan.

What gauge would you Clapton?

Sent from my HD1907 using Tapatalk  

Was happily vaping with a 1.2 ohm build on the RBA with istick 20w. Today I finally got my 30w mod, so exited to try sub ohm, switch to the 0.5 ohm occ coil and wrap the deck with tissue paper and leave it on my table, go out enjoy the Vape than come back to my desk continue work and forgot about the deck.

by the time I finish all my work, I plan to switch back to the 1.2ohm RBA deck, by that time I realize that the tissue on my desk missing. Search for some time than remember before I go out Vape i clean my desk, than turn and look, dustbin has been empty......I'm so sad.

i wonder is it posible to get only that section? I have contacted kanger, hope they reply soon.

i love that RBA.  

Hi all and thanks in advance for all help.

I have

26ga + 32ga SSL
28ga + 32ga SSL

And for the life of me I can't workout how to get a coile wrapped at a decent ohms for a single coil to go in my aromamizer v2 single deck.

Can anyone help and suggest what's the best ohms to be using for single coil.

Thanks  

Just bought the Kangertech Subtank..... Was told I couldn't use my Max VG juice and I needed to buy some of their lower VG juice. I told the guy no thank you, I know what i'm doing and I can make it wick the Max VG.

Needless to say I got home, the STOCK OCC coil, .5 ohm, wicks my Max VG perfectly fine, even with chain vaping.

I ripped the pre-made coil out of the 1.2 ohm OCC head, and built my own .6 ohm coil in it, wicked it with Organic Cotton (Not KGD or Bacon, Just organic cotton from Walgreens) and it wicks perfectly fine with my Max VG.

I built a single coil .7 ohm spaced coil, wicked it with the double tails on each side, cut off to where it touches the deck, but not touching the threads, put the chimney cap on, and made sure the juice channel was free of blockage, and it wicks perfect with the Max VG.

No leaks, no dry hits, running each OCC head at 30 watts, and the RBA deck at 35 watts.

This is the original Subtank, 6ml for OCC and 4.2 for RBA, (NOT THE NEW 7.0mL version).

So let me hear it.... What have you guys noticed or seen about the wicking ideas, why has yours not worked?

WHY DO SO MANY PEOPLE SAY YOU CANT USE MAX VG ON RTA's, especially on the Kanger Subtank????  

So I'm a toodle puffer. My normal set-up is a Joyetech Evic Easy and a Kayfun lite with unflavored liquid. The Evic Easy has a regulated 3.3 volt mode and an unregulated mode. I run the Kayfun (original V1) at 1.5 ohms, so I'm vaping at a whopping 7 watts.

Just on a whim, since I was ordering some supplies and stuff, I decided to try one of those new-fangled subtank minis...hey, it was on sale. This is my result after 2 days.

First, the .5 ohm was out of the question, so I primed and put in the 1.2 ohm OCC coil. Well, this was just not a good fit for me. The problem is, I think, the wire guage. I bet the coil is made from 24-26 guage wire. My 3.3 volts took forever to heat that wire. I had to hold the button down for 3-5 seconds to get any sizzle at all, and just couldn't get much vapor.

So, the next step is to try the rba base. This is very kayfun-like, and I built it the same way. Inspecting it, I found a burr on one of the juice channels, but filed that off with a needle file. I built a 1.8 ohm 30ga 2mm coil that turned out to be 2.0 ohm...oh, well close enough. Wicked it with my typical cotton ball and laid the tails across the deck.

I looked at the mouthpiece. Are you kidding me, looks like a tailpipe. Swapped to a favorite drip tip, turned the airflow to the lowest setting, and started vaping.

I've gone thru 2 tanks, and it's working great. Maybe better than my kayfuns. I'm going to try rebuilding the OCC coils for backups, and will likely get a couple more rba bases. The beauty may be how easy it will be to swap out the coil.  

I don't know if anyone has issues with their protank 2 but I hear a lot more negative than positive on them. I was messing with one of those bootleg ones and I couldn't figure out why it kept on leaking. Now just yesterday a friend gave me his protank 2 and Im guessing it was because he was tired of it leaking. When I first took it apart I took all the pieces off and connected them all again one by one making sure it was air tight as I added each piece. Everything was air tight until I got to the coil. I was taking a drag off it and it immediately started leaking and I was like why the heck does it do that? I noticed that it was leaking from between the coil and atomizer where the two little airholes are. What I did to fix this was take an old coil and gently pull off the little silicone ring (above where it says the ohms and below the wick) then I dropped it into where the coil meets the atomizer. After I just screwed in my coil and it works perfectly. No leaking whats so ever! Very good cloud production so far I recommend trying this if you have one. Sorry if someone already wrote this but I did a lot of looking around and never found an answer. Also didnt know where to post this so I apologize if this is the wrong section.  

So I decided to try a 1,6 ohm coil on kayfun v4 clone Tobecco and I am using 28gauge Kanthal with a cotton
wick on a Rdna 30 and its vaping well at 15 watts I have a kanger subtank mini coming in the mail and here goes my question
So the kanger subtank states that with a .5 ohm coil i could vape up to 30 watts but the voltage comes in at like 3.8 volts
I was under the impression that the rdna 30 needs at least 4 volts to work which kinda brings me to my second question
What is the point of of sub ohms? cant i just build a 2.0 ohm coil or something like that to achieve the results as if i was subohming
I am very confused on this
thanks for the replys in advance
Oh yea is a 1.6 ohm coil at 15 watts a normal build or any recommendations for the kayfun v4 for watts and ohms thanks again  

Got no idea what this thing falls into...

The MechLyfe Ratel 80W (8.5V). It uses an external 18650 battery and it uses an RTA build deck. I’m not sure if you can use pre-made coils for it though. You can use it in both DTL and MTL but with MTL it’s loose draw. You can’t adjust the airflow on the fly, you have to take the panels off to make the airflow adjustments.

The build deck looks nice and simple to build on. You might get away with fitting in an alien coil.
 

okay, so i had a problem yesterday where i would keep getting juice popping up on the draw, that problem is solved, however, now on only the second day of light use, on the 1.2 ohm coil that came with the tank i am getting a pretty harsh smokey taste. Its not overwhelming like it is when a coil is burnt out, just an unpleasant taste. I did 4 drops of liquid on the coil before using, everything is screwed in tight. Do i need maybe a couple more drops on the coil?

FYI: using an istick 30w burning at about 14.5-15w  

Hey guys whats up. Well I had gotten the Sub Mini tank, the first tank I got was a dud. I had nothing but issues with it since day one. Coils went bad in 1.5 days both coils, then the rba deck was giving my sigeili issues and errors.

So I sent it back, They replaced it, and I now have Version 2 as they say. This tank has 2 air slots and different Holes in the tank. I used the Stock .5 coil but was just getting wayyyy too many dry hits.. So I went to the RBA deck, been using the coil that came with it, and I have 100% organic cotton. So I been using that, but now I am getting Dry hits with this thing!!! every 4th hit Is Dry!! I have to cover the holes and pull to get teh cotton wet again, and then 4th hit shes dry again.

What is going on here? Anyone else have issues like this? I am really getting fed up with this and ready to just throw it away. What can I do about the situation or why is this happening?

E-juice = 80/20 Clear Liquid all fruity flavors 3MG