So..hmm.what gauge shud I get? I'll b having the prebuilt coils n I want the wire to learn to build a simple coil,any recommendations on sites for high length cheap price? I've heard higher resistance for beginners so maybe what 1.5 ,2ohms? Help me!
I never used anything but Kanthal and Nichrome wire to build my coils.
All things being 100% equal (wire gauge, coil type, coil diameter, ohms, etc) do SS coils require more power to run to get the same vapor as the exact same coil/resistance made from Kanthal or Nichrome wire?
I've always wondered whats better for efficiency. In a regulated mod I can't imagine it really makes a difference in vape performance, I'm currently keeping my builds at a lower resistance by winding parallel coils. My goto build comes to about 0.4ohms and I run it in the range of 28-38w, usually set at 32w, if I wound it in series it would be around 1.6ohm which would need about 7v to get to 30w and at my Aegis solos max voltage of 8v would provide 40w. The only issue with this is that it limits the wattage range you can run at, since I sometimes do crank this build upto 42w, although it does start to burn above 45w.
The one advantage of running at a high voltage and a lower current is that theoretically there should be less energy loss in the transmission of power to the coils (like in the pin, the posts and the wiring connecting the 510), although depending on the construction of the mod/tank it may not be significant enough to provide any benifit. I can imagine that it's not that simple either as the mod is having to boost the voltage more which may cause the voltage conversion efficiency to suffer. Although in my dual cell mod it may be benificial since the input voltage is around 6.4-8.4v, although I tend to use this for my higher wattage builds.
This may just be me because I'm obsessed about how much voltage is dropped across cables, I always use the high quality wiring and keep it as short as possible because it is actually quite surprising how much energy you can loose through a cheap cable. Even good quality wire at higher amps can drop a significant amount of power.
I am kinda a noob when it comes to prebuilt coils. I am looking for coils that feel very strong/sturdy, but I am not sure what material it is.
I had coils that said they were .25ohm and all it says is "KA1 WIRE + Ni80 wire" and they felt very sturdy/hard to pull the wraps apart etc....
I bought what I thought were a good replacement for those, but they feel flimsy and easy to pull apart the wraps. They are .36ohm, 316l stainless steel, 30gx4/36g.
So apparently the stainless steel wires are more flimsy...I cannot seem to find coils that have KA1 + Ni80 like the sturdy coils I once had. I
am trying to figure out which material/what I need to look for in order for the coils to be sturdy like the old coils.
Can someone help me out with this? Thanks in advance.
I am trying to get the best flavor with the best single coil build.
Objectives:
Flavor
Smooth Vapor
Materials:
Kanthal Wire
35mg Nic Salts
I have noticed that either depending on the diameter of the coil or the spacing of the coil wraps You get a different kind of vape hit. It seems like higher gauge wire produces a smoother hit. And then couple that with a small diameter coil build, plus squishing the coil together to remove all coil spacing results in the smoothest possible vapor.
Can anyone confirm my findings? Or does anyone have any tips because I have still to replicate the smooth hit from clearomizer sub tank cartridge's that are non mesh. I am starting to think this is because the cotton is wrapped around the outside of the coil instead of being shoelace through the middle of the coil.
Can someone help explain : why thicker wires (lower gauge) since they have less resistance why would they take longer to heat up ? One (me) would think the lower resistance would make heating up quicker- where am I going wrong ?
Thx.
Sent from my iPad using Tapatalk
When calculating builds on Steam Engine for parallel builds, is the wrap count the total of wraps counting each strand, or total wraps for the unit of strands?
Example: I want build X using 2 parallel strands of 28g Kanthal, and for my given resistance, SE says use 14 wraps. Is that 7 wraps with parallel wires, or 14 wraps counting the parallel wires as a single wire?
Thanks in advance, guys. I'm trying to experiment with some creative builds and I want to waste as little wire as I can on missed resistance.
Just a little warning to all who have purchased the Lemo 2- Do not use the wire included in the box.
I was a little worried when i was using the stock coil and noticed it had been turning a green color after a few days of use, not sure if this is the case with all Lemo 2's, but if you notice your wire is turning greenish, just throw it out and replace it. I don't believe this is kanthal, it could possibly be nichrome, but it's properties are not matching up with those of kanthal. My worries were confirmed when I decided to put a parallel 5 wrap coil on my rda with that wire because of my lack of other 24 gauge... Well today when I took out my cotton and dry burned the coil a little to rid it of excess juice, the coil actually deformed and somewhat melted on my rda . I don't know what kind of metal this is, but I'm positive it is not kanthal, this has never happened to me with kanthal, and this wire seems to be of a lower resistance than kanthal. Anyway, just wanted to let ya'll know to be careful with that wire, or just throw it out altogether. Otherwise, the Lemo 2 is a fantastic tank
Hello so as of now I have a 100 foot roll of .26 gauge kanthol that ive been using litterally ever since i started getting into rebuildables. I have been looking for some thicker wire, and i was thinking .22 gauge but idk just wanted to hear what gauge you guys vape with!
Does anyone know what gauge wire the Lemo2 comes w/? It doesnt say but its real heavy. I like it. Coils keep their shape better when wicking thick.
What is your go to single coil build in terms of gauge wire, diameter, and number of wraps : (no fancy Clapton or twisted build just a "regular" wrap)
And if you have a reason please include it: For example: "I'm a flavor junkie and this is best flavor build I've found" or "I like short ramp up times" etc ...
(I know preferences may vary greatly)
Thank you very much
:
Sent from my iPad using Tapatalk