Kayfun L + Drip Tip Getting Hot

I bought the MVP 2.0 Starter kit from Mt. Baker. I like the tank it comes with, but I feel like using a drip fits me better. I started with a eGo like everyone else and recently moved to this Box mod when I saw it for so cheap on baker.

I want a drip setup because I don't vape all the time, but when I do, I like to control how much I vape so I don't binge on juice.

Any setups for "Drip"

Prefer to keep it nice and cheap, as a college student, money is a big problem.  

Hi Guys, If I don't use a spiral drip tip I get a dry mouth. I bought a bunch of innokin jems because the aspire k2 is discontinued. But the Jem the drip tip is attached to the top. Can anyone suggest anything, Maybe there is some other kind of top that would fit it or something, because I've spent quite a lot on them. I normally get my supplies from fasttech.

Thanks for your help
Purr.  

I am a confirmed tootle puffer although a chain vaper. My coils are generally 1.8 to 2 ohm and I rarely go beyond 11watts. Even when on a whim I wrap a slightly lower ohm coil I still never go beyond 13 watts. Still I find my drip tips get too hot and burn my lips especially when I use the kraken. I have sores in a couple of places. Is there a way round that. The other day I bought a couple of long ceramic drip tips, the ones normally used for e-pipes but I find they get filled with too much condensation.

What do you guys do? Do you have this problem?  

I just received my Atlantis 2 today. It works well, except what's up with the drip tip? It's so large you can only directly inhale into your lungs. Are there other drip tips you can put on it?  

Hello.
So I think i kind like a cooler vape been getting some heavy lung feeling lately been vaping a 1.2 ohm single coil 28 g kanthal
cotton wick on kayfun clone v4 Tobecco, i would like to try like maybe 1.8 or a 2.0 ohm coil or is the kayfun v4 really better for
lower ohm coils I keep reading where the kayfuns sweet spot is like 1.2 - 1.5 i did lower my wattage from 14 to 12 but i like to seem some clouds more of a flavor chaser than a cloud person though
so i am just wondering if anyone has tried a kayfun around 2.0 ohms and what the vape was like
thank you  

So I'm a toodle puffer. My normal set-up is a Joyetech Evic Easy and a Kayfun lite with unflavored liquid. The Evic Easy has a regulated 3.3 volt mode and an unregulated mode. I run the Kayfun (original V1) at 1.5 ohms, so I'm vaping at a whopping 7 watts.

Just on a whim, since I was ordering some supplies and stuff, I decided to try one of those new-fangled subtank minis...hey, it was on sale. This is my result after 2 days.

First, the .5 ohm was out of the question, so I primed and put in the 1.2 ohm OCC coil. Well, this was just not a good fit for me. The problem is, I think, the wire guage. I bet the coil is made from 24-26 guage wire. My 3.3 volts took forever to heat that wire. I had to hold the button down for 3-5 seconds to get any sizzle at all, and just couldn't get much vapor.

So, the next step is to try the rba base. This is very kayfun-like, and I built it the same way. Inspecting it, I found a burr on one of the juice channels, but filed that off with a needle file. I built a 1.8 ohm 30ga 2mm coil that turned out to be 2.0 ohm...oh, well close enough. Wicked it with my typical cotton ball and laid the tails across the deck.

I looked at the mouthpiece. Are you kidding me, looks like a tailpipe. Swapped to a favorite drip tip, turned the airflow to the lowest setting, and started vaping.

I've gone thru 2 tanks, and it's working great. Maybe better than my kayfuns. I'm going to try rebuilding the OCC coils for backups, and will likely get a couple more rba bases. The beauty may be how easy it will be to swap out the coil.  

I was going through my stash. I clean it out regularly and give away stuff that I no longer use. I have a Wake Mod RTA that takes both coils and you can build on it. I actually like the tank and it has a proprietary drip tip that I, of course, lost. It would be a tank that I'd hang on to just to future proof me if I had the drip tip.

It has been on my mind to try to find a replacement drip tip and so far no luck.

The other day I found one so I ordered two of them. I get an email letting me know that I have to verify my age by taking of a photo of me holding my ID. Are you friggin kidding me?

Immediately I got very irritated - certain things just set me off --lol. I replied to the email with a cancel my order and refund me and cancel my account as well. I also let them know that I have been purchasing vape products online for years and have no issue going through an online process but I am not taking a photo of my ID with me holding it and sending it to you.

Received an email just now with a tracking number --- I guess the drip tips were mailed --lol.  

To all the mouth to lung (Tootle Puffers) here ... There was a time when the famous "Kayfun Lite-Plus V2" was the gold standard when it came to single coil / higher ohm / low amp Tootle Puffing.

Now that this atomizer (to include all the Chinese clones of it) are so very hard to come by (to include spare parts), has anyone here replaced there old Kayfun Lites with the new "Kayfun Lite 2019" atomizer ?

I just ordered a couple of Chinese clones of the Kayfun Lite 2019 so I can make the big changeover.

Good bye to the sweet Kayfun Lite-Plus V2
Almost 6 years vaping on this
Rest in Peace ....

 

really random and specific question here. i recently got a kanger subtank mini. love it. around various vape shops and what not i see a lot of people with the subtonic mini but with a 3rd party drip tip. most of the times the tips are really short. idk why i just think it looks really cool but i don't know where to look for such drip tips. anyone have any pics or recommendations they could share?  

I have a subtank mini and every drip tip I have doesn't fit. I really like the stratosphere stainless steel drip tip. Stratosphere Stainless Drip Tip - 510/901/KR808
But I don't wanna waste my money if it doesn't fit.