Its Time To Upgrade The Pipe

Hey there guys, new here.

I have a Vappresso Revenger Mini kit and I have upgraded my tank from NRG SE Mini tank to a "Geekvape Z Sub Ohm tank(Much Larger Tank)". Because I wanted to taste more flavor and still blow lots of clouds in the air with my vaping device being fairly cheap.
I put a New Geekvape Z series coil 0.4ohm 50-60W because I burnt my original 0.2 Ohm coil , I wont talk about my previous coil. I'm getting 2 problems here.

1. I'm using 60W, normal setting and every time I vape or inhale I get a taste of E-Liquid in my mouth. However its blowing perfect clouds and still getting an amazing taste but its just that the liquid drops in my mouth. I just want to spit it out every time. How do I fix that problem?

2. The other thing is if I use Higher Wattage and High settings the liquid pours out of the air flow and starts leaking and backspits in my mouth.

(Before I vaped with new coil)I put the new coil in, I soaked it for 10-15mins, while I fill half tank of E-liquid which is 0.8Ng/0.2PG. Then I inhaled 3-4x with no button pressed. Then I vaped to test, still leaking. I set the vape to 70W and high setting then blow downwards into the device 5-6x. All I was trying to do is desaturate it. My results got better didnt notice much of a leak but I still get a little bit of liquid in my mouth. If you can help me out here, I would much appreciate it.

Thank you and kind regards

Tuatara Vaper  

Hello
I have the wotofo serpent rta top airflow single coil tank now and I just purchased the augvape druga rta. Flavor is 100% better in the augvape drugA rta but juice leaks out the bottom of the tank every time which is why I have to stay with top airflow as it never has leaked on me. So I’m looking for a top airflow rta single coil . I typically vape between 20-30watts so I don’t need a powerhouse. I just want the flavor and don’t care about clouds. Can anyone recommend the best top airflow rta? The wotofo serpent works well but it takes a hit on flavor. The serpent only has 2 small air holes around the coil area and I think this is why it isn’t producing a good vape. I was looking at the Zeus? Augvape intake of the dual one? Or any others anyone can recommend ?

primary goal: outstanding flavor
No leaking
Lots of air holes around the coil


thanks for your time  

Just two questions.

Ive been using a Vision spinner 2 1100Mah for a long while now with a Kanger Aerotank V2 which has been very good and reliable.
I recently got a Kamry E pipe as a gift. The Kamry takes a 18350 battery.

Problem is there isnt a lot of difference in vaping between the two, this is with the same tank with the same coils on both. Is this normal? If anything the pipe loses vape sooner due to battery drain than the Vision Spinner 2. Is there anything i can do to beef up the E Pipe for a better throat hit and more vapour?

Which brings me to question 2.
Is there a good upgrade to the Kanger Aerotank? I want a new tank anyway to replace the stock Kamry one which is top fed and tastes burnt quickly, and i dont want to keep changing out tanks between the Kamry and the Spinner hence i need a good, ego threaded tank for the mech pipe. (Kamry k1000 is 510 threaded but i have a 510 to ego adaptor too)
Thanks in advance  

I know, I know... this topic has been discussed to death. And, I am in the process of searching now.
I have a TFV8 tank that started leaking a week or two ago. I tried all the usual tricks (empty and clean all parts, don't over tighten, replace o rings, etc). Nothing helped. After a few days of covering the mod with a paper towel everytime I took a drag, I decided to buy a new tank. The new TFV8 arrived yesterday afternoon, and after checking it out and filling it with juice, it is doing the exact same thing.
We are not talking about a drop leaking here and there, it is leaking the whole tankful in less than two hours.

Any suggestions?

Thanks!

Sent from my SM-G965U using Tapatalk  

Im pretty much freaking out right now, I have been vaping the same juice for 7 years and I just received the 3 bottles that I ordered and I went through 8 coils thinking I had bad coils, well it wasn't the coils I went and smelled my juice and it smelled like a burnt coil with a mix of burnt plastic. I called and they said they didn't change manufactures so I'm assuming something went wrong in the lab. Anyhow I have 1 good bottle left and that's only 30ml, I vape USA #1 from Ecig pros and hopefully they fix it otherwise I'm going to have to wait until they get there next batch which will be a while, because they just got this batch. So I need to find a new juice to vape for now, I prefer max Vg and tobacco flavors but not with the Carmel or dark colors. I love a little nutty flavor, so please can you give me some names juice and where to get it. Also I don't do the salt nic. Thanks so much  

I have been making my juice 50/50 from the beginning about 3 years. I can't remember my initial reasoning. Every atty I have leaks to one extent or another. It's about time to make up another 500 ml of juice. I was thinking about making it 70/30 hoping the thicker juice will stop leaking. Any advice?  

Hello,

I am having a leakage problem with my TFV-12 Beast King. I have been using this tank for roughly 3 years and I have never had this issue shy of leaving it in the car when I run into the store or forgetting to grab it rushing into work. I tend to stick to the same juice at large chunks at a time. I have been vaping the same brand and flavors for the past year or so. I also stick with the same coils, either the T6 or T8. I have also used the same mid for 2 years. This is not just a subtle leak either, it is dumping tanks at a time through the air vents. I have replaced the o-rings all around just in case and still no luck. As much as I hate to think like this, the leakage began around the same time of the release of the TFV16. Has anyone else noticed this issue with their V12 or have any recommendations on a proper remedy.  

Hello all,
I’m sure this has been discussed before as this is not a new tank, but after doing a search I didn’t find an answer. I also didn’t find much help on YouTube. I just pulled out my 2k18 doggystyle (I think that’s the correct version, it is a top fill) and built and wicked it. It has been so long since I bought this and read up on it, I don’t remember any of the tips and tricks.
As soon as I adjusted the airflow, ejuice started leaking in large amounts out of the holes. Luckily I was able to salvage most of the juice as it was premium juice I just bought from a store (not diy). What did I do wrong? Is it a wicking issue or is something else wrong? Any suggestions are greatly appreciated! Sorry if this has been covered before, but didn’t know where else to ask and I want to get this tank to work.  

Well I bought a mod and a kayfun and after about a week of fiddling and trying to get it to work its just way too much of a hassle so I am probably going to sell it to my friend that wanted a mod and kayfun anyway. Now I currently tried to upgrade from mini nautilus and vision spinner 2 to mod but I kind of want to downgrade even further since I went through 2 vision spinners and 2 mini nautlius in about a month and a half so obviously I am not happy. Im sure you all know why i hate the mini nautilus. But now i was thinking about going back to the Halo g6 starter kit that i got started with vaping. When i look back it was so hassle free, convenient, and i didnt attract attention like the bigger batteries etc which are usually frowned upon by people in the general public. I use 12mg so I was wondering to make up for the smaller battery and vapor that i should upgrade to 18mg? Yes I know im going to end up spending like another $100 for a starter kit and halo ejuice which is expensive since its $20 for 30ml and other ejuice doesnt seem to work in the g6 cartridges. I really need a 2nd opinion on what people think of this plan. The g6 should last me awhile unlike the vision and mini nautilus which id have to keep rebuying which is like $50 a month even though i buy off mtbakervapor which has much lower prices than halo even though its also prob lower quality. What do you guys think? Are mods just an addiction hobby thing that smokers actually need.  

So I ordered an e-Pipe 628 from China, and it worked for a day, but now I can't get the coil to fire. The distributor offered to take it back, but maybe someone can help me figure out what's wrong with it, so I don't have to go through the hassle of wrapping it up and shipping it back overseas (at my expense).
Anyway, it's fully charged, and I definitely know how to work it, but when I connect the bowl to the cartomizer and push the button, nothing happens. I took the bowl apart and looked for a loose wire, but everything appeared to be in working order. I've also tried all three cartomizers, and none of them work anymore. (They all worked the first day.) I'm pretty sure the battery's center pin is making a connection with the cartomizer. I even pulled the center pin of one of the cartomizers out a little bit to make sure. Is there anything else I'm missing? My daughter swears she didn't drop it when I let her use it. This is so frustrating! I can figure out pretty much anything by fiddling with it long enough, yet this thing is giving me heck! I've been at it for over a week now.