2nd Build

I got my first Derringer today. Wanted to try it immediately although I bought it with the DAY AFTER (May 2106) in mind... but you know how it goes, you get a new toy and you want to try it out.

I'm really not into very low ohms so first I went for a single coil - 26 AWG Kanthal, 9 wraps for around 1.3 ohms. But I didn't like the way that could be wicked in an rda. So then I put in two 28 guage coils which I had previously coiled for my other atties. Together they gave me .8 ohms which is sort of ok. But I still am not quite happy with the wicking. These coils are 2mm internal diameter and there's not a lot of cotton you can put in there. The taste is good but my wicking is nowhere as fat as I see in some pics online.

Any advice?  

So no mine didn't melt haha but I was wondering what the best build would be for a plume so I could prevent this? I normally go with a .3 ohm build 24 gauge 7 wrap so yeah thanks guys!  

So i build my coils, but i wanted someone get my wraps tighter, so i asked a friend, and he recommended me too one of our vape shops. the guy there said $5 per coil and 5 for wicking, is this just outrageous or whats the normal price for a build  

Hey everyone,
I've been vaping for about two years now, and have decided to start dripping. For the last few weeks, I have been dripping on an IGO-W, 26G Kanthal single coil (7 wrap micro coil reading at 0.8ohms) on my iStick 30w.

I just recently purchased a new battery that should arrive today, and was wondering if anyone had advice/tips on producing some fat clouds! Dual Coils? Different coil builds? Number of wraps? Watts to vape at? I think you get the picture lol.

The items I will be using are as follows:
-SMOK XPRO M80 Plus
-IGO-W
-26 Gauge Kanthal Wire
-Japanese Organic Cotton
- 80vg/20pg Juices

All input is greatly appreciated. Thanks!
-Tyler  

I never used anything but Kanthal and Nichrome wire to build my coils.

All things being 100% equal (wire gauge, coil type, coil diameter, ohms, etc) do SS coils require more power to run to get the same vapor as the exact same coil/resistance made from Kanthal or Nichrome wire?  

Hello im looking for a RDA, I have had a shop around and I have narrowed it down to a few, the tobh atty, plume veil, magma and the dark horse dripper. I am more leaning towards the tobh atty as personally it looks the more simple to build on. I will be trying to build .5 ohm coils as that's what im using at the moment (aspire Atlantis) could you give me any advice/recommendations  

GS Air coils/GS 3ml tanks.
I Googlefied this and Did see One place that said A worn out tank could make coils not last as long. (Sounds near fetched to me...)

Can an old tank start Causing premade coils to show Low ohms, like. 05 ohm?

I am pretty sure these are factory coils not FT copycats.
Bruce in Ocala, Fl  

I just Started rebuilding my kanger dual coils and im having a issue , seems like when i build them and check my ohms on my meter they are right where i want them but when i put them in my tank and fire them up the ohms fluxuate like crazy from low to high ohms, any idea why it happens ? It occurs even when i build single coils. Anyway to fix this? Thanks  

I have the Smok xPro M80 plus and I have a couple Kanger subtank minis I use with it. I usually use .5 ohm coils. Sometimes it will show the ohms fairly correctly at .54 or even .61, which seems close enough. However, as I puff, the ohms reading will tend to change after every few puffs. Sometimes it will even say up to 1.5 or 2.0 ohms on the same tank coil! One tank seems to do it worse than the other, but the two I use now both will change quite often, and once in awhile quite drastically. It sometimes helps if I unscrew the tank and screw it back on, but if it isn't really tight, the ohms read are really far off from what they should be. I'm not sure if it is the tanks or the M80 plus that has the problem. When it reads really high, if I don't catch it before I take a puff, it is horrible and burny-dry, since it thinks the ohms are so high...

Has anyone else had this problem and/or have any ideas as to how it can be fixed??

By the way, I've cleaned the connections and everything thoroughly, so it's not that...  

So, I'm familiar with battery safety, load, amp max for safe use, etc. I also know about ohms law. I'm on a regulated mod with an archon v2 rda and have just wrapped my 3rd set of coils. Three strands of 28ga. Kanthal. Two coils reads on my mod at .12 ohms. What's a good wattage range? I have a dual battery sigeli mod that goes to 200

[Edited]