Hello everyone I recently purchased an ipv mini v2 and I love it, it is working perfect. I only have one complaint the fire button rattles like crazy and it drives me nuts. To some it's not a big deal but I just don't like it. So do any of you out there know if there is a way for me to fix this? Once again everything else is perfect ohms and all that it's just the fire button. The wattage up and down buttons are supper tight and clicky. Any help would be greatly appreciated. Thanks
Right now I have a few box mods, the IPv3, SIG 150w and the Snow wolf 200w. I'm using the Snow wolf 200w and honestly I'm not happy with it. I've had the button stick a few times causing it to auto fire and I'm noticing an almost one second delay from when I hit the fire button to when an actual vape starts to kick in (very slow fire up time, and I'm only running dual twisted 26g) on top of that I really dislike that I have to hit the fire button to see how much volts I'm using. I know the SX M class is one of the best out right now, but the fact it's a single battery concerns me because I typically vape between .12-.20 ohms and usually 60-80w (but since getting the derringer it's been 60). I really like the hot, dense flavorful vapes and I wanna make sure if I get the SX M class it'll be able to deliver that.
Well this sucks, I have an iStick 30w and toptank mini, I ran out of pre made coils so I thought i would try the RBA of the toptank. At first it read out as “protection” upon trying to fire it (I think the ohms were too low on the pre made coils included with the RBA at .1), then it said low battery (it was almost fully charged) so i plugged it in and tried to fire it once more and the thing started smoking (no protection message this time, just a little puff of smoke within the LED window). I only fired the button for a split second and it still seems to be functioning. Not sure what I should do lol or just ditch out on it? It appears to be working yet but stinks like an electrical fire now. I’m kinda reluctant to use it (I still have an old coil but it was starting to taste funky). Any advice or idea what might’ve happened?
I have had a lot of mis fires on my Smokless Owl 25.00 squonker and had to press down extra hard
and sometimes side ways to get it to fire.
I just done some contact cleaning and scraping on the Smokless Owl Button.
I took my wifes Emory board finger nail file thingy and depressed the firing button and held it depressed and rubbed it
across the firing pin and then took a small jewlers screwdriver and scratched it back and forth across the end of the pin and
did the same thing to botton ground pin.
I noticed some black color on the end of the firing pin before I started this cleaning process.
I gently took the screw driver and scratched back and forth across the positive and negative end of the battery just to
take any small film or oxidation from the ends just to make a better connection.
It seems to fire now just like it should with no MISFIRES---mod is now perfect !
I've got a couple of these little mods and both have the same problem. They continue to fire after the button is released. When it happens the display changes to the power on/off and keeps firing until the unit restarts (presumably after the 15 second cut off?). I can only think that the mod is registering 3 presses when I fire which triggers the screen change, and there is a bug which stops the release of the fire button registering. Anyone experienced this? Any fix? I'm surprised it's happening with two units so it must be happening to someone else!
Hello very basic question I love dripping and do it all day my one problem is with the mech mods I have I cannot place them down with out locking them or they fire sometimes anyone know of a good clone that will not fire when placed down maybe one with a recessed button of sort?
I currently have a F U and a Stingray infinity
I accidentally locked the up and down buttons by pressing both of them simultaneously for 2 seconds, I have tried unlocking them by doing the same thing like the instruction manual calls for. It doesn’t work, no “unlock” pops up or anything. You can hold them as long as you like and...nothing.
I have since figured something might be wrong with it as I am almost positive I’m doing it correctly. Now I have tried getting the reset button to work in hopes of the up and down buttons being unlocked upon reset. I hold the reset button for 5 seconds and I’ve tried the method of the combo with the fire button and reset as well as the up arrow and reset and the screen goes blank and turns back on but never says reset and the settings are still the same as before.
My next idea is plugging it into my computer in hopes of an update fixing this but other than that I am out of ideas. The device is stuck on 20 watts which is too high for the cartridge I’ve got on it. Does anybody have any ideas, please help me out.
Hey guys.. i been vaping for a while and not had this hapen before.. i am using a Hugo Vapor Rader and ot has been working with no problems until today... when i go to use it, when i try to fire, it says high atomizer the first time i push fire button followed by low battery (have tried multiple sets) when i press again. If i persevere and keep attempting to fire it works fine as if there were no problem until the next time i go to use the device when the process repeats.. i have taken the tank apart and cleaned and put back but the issue continues.. anyone have any ideas on what is wrong/what i should do?
I have a hades 26650 mechanical mod and I was running a tobh atty v2 dual vertical coil build. It was working perfect but I was getting tired of dripping. I bought an aspire Atlantis, and it won't fire. I feel as though it's my mod, because I was fumbling with some adjustments on it, and it fired for about seconds. I was very happy with the production and flavor. But, now no matter what I adjust or anything, it won't fire anymore. I cleaned the connections and everything. Please help!
Hey everyone. I've noticed that just about every day since I've used it. When I hit the button to fire it, it will fire for a couple secons then stop, and then fires back up again. And it's starting to concern me. Does anyone else have this issue? And how would I go about fixing it?
Well I did a quick search and couldn't find a review for the Sigelei 30watt mini and figured I'd make one now that I received mine. I have no clue how to post vids through my phone so I apologize for the primitive text review haha. So here we go my review of the Sigelei 30watt mini:
Includes:
Sigelei 30watt mini
Micro usb charger cable (located inside battery slot)
The 30watt box mod is yet another great mod from Sigelei. Standing a little over 3 inches tall and an inch deep it is definitely a stealthy little device. This device comes with the standards of all sigeleis. A fire button, 2 function buttons and a display screen. And of course it's loaded with the standard safety functions:
Low voltage protection
High voltage warning
Reverse polarity protection
Low resistance protection
Short circuit protection
It also includes 5 memory banks for quick wattage changes. Wattage range from 5-30 watts in .1 increments.
PWM mode and DC-DC mode. 5 click power on-power off. Voltage display and ohm display aswell. The device requires 1 18650 lithium ion battery which inserts to the back of the device via magnetic battery door, that's right! MAGNETIC! Now here are some pros and cons I've found for the mod.
Pros:
Clicky buttons, gotta love the click.
The magnetic battery door
Size, this thing feels great in hand and fits nicely in pocket with a Kanger subtank on it.
It's made of a nice solid aluminum alloy without any goofy etching or screws.(except for on the top and bottom)
Extremely easy interface. As this is my first box mod I found it nice and easy to navigate the modes and memory banks.
Most tanks and rdas sit nice and flush on the box. I'm using a 22 mm subtank mini and there is no over hang. And even with a 25 mm tank there isn't much at all.
Cons:
Now these aren't necessarily cons but just things I personally didn't find great.
It comes with a silicon sleeve, and I don't feel it necessary. And with it on the buttons become flush and harder to press.
Small screen. I am far sighted so having to squint all the time blows. You 20/20 people will have no problem though haha.
Doesn't include a battery. For something that is definitely targeting newer vapers, not hobbyists, I felt it probably should have had one with it.
The fact that it changes wattage at .1 increments is pointless honestly. I can't tell the difference between 15.3 watts and 16 watts, so what's the point?
For everything it does and everything the device comes with, it's definitely a good choice of beginners or seasoned vapers looking for another nice mod. Price varies from vendor to vendor but is pretty on point. I received mine from VapeHappy.com for 36 bucks. It also comes with a 3 month warranty from Sigelei.
I highly recommend this for just about anyone and give it a 8.5/10 due to the fact it doesn't come with a battery.
Again sorry for no video and no pics but I can't figure that crap out on my phone. I hope you enjoyed my review on the sigelei 30watt mini.