Kbox Problems

I've been using my Atlantis on a Kamry K101, and just got hold of a Kbox because I wanted to boost power. Unfortunately, the Atlantis won't fire on the Kbox. Charge indicator shows battery full charge, but it won't fire on any wattage selection.

The Atlantis I'm using fires fine on other batteries I've tried, and the Kbox fires an iClear 30S with no problem - it just seems the Atlantis/Kbox combo doesn't want to work together. The contacts on tank/battery are clean, no gunk or liquid in them.

I've tried Googling the issue, but all I'm mainly finding is people recommending the two together as a good combo.

Does anyone have any idea what could be causing the problem?

Thanks in advance for any help.  

I got a problem with my Luxotic Surface. I'm using a LG Choco Battery 18650, it was fully charged and when I press the fire button suddenly it appears for Battery Low even the battery was on fully charged. I tried my spare battery maybe its just a mistake putting a fully charge battery, but it was the same issue also with the spare battery. I tried the 2 batteries with my Geek Vape Aegis 100W to check whether my batteries are already broke but it works fine. I was vaping for my Luxotic Surface by 55.0 Wattage, 0.21 ohms, 3.40 Voltage. Can someone help me out to fix this problem?  

Hey guys,

I finally updated my charger a few days ago (I think before I had the VP2) or something like that. Quick question on something I'm noticing that seems a bit odd to me.

When I charge (for example 18650's), a battery that's fully charged in channel 1...it flashes FULL/0.00 mA, I remove the battery. A few minutes later, I'll put the battery back in the same bay, and all of a sudden there are a few hundred mA's that show up on the screen that need to be charged back into the battery and it takes a few minutes for channel 1 to recognize the battery is fully charged and flash FULL/0.00mA again (although it does show above that's fully charged at 4.2v).

If I take that same battery and do the same test but this time in channel 2, within a few seconds it recognizes that the battery is fully charged and flashes FULL/0.00mA. So it seems channel 1 is not working as well as channel 2 is, when it comes to recognizing information from the battery.

Is this normal for this charger or do I have a defective charger?  

Well this sucks, I have an iStick 30w and toptank mini, I ran out of pre made coils so I thought i would try the RBA of the toptank. At first it read out as “protection” upon trying to fire it (I think the ohms were too low on the pre made coils included with the RBA at .1), then it said low battery (it was almost fully charged) so i plugged it in and tried to fire it once more and the thing started smoking (no protection message this time, just a little puff of smoke within the LED window). I only fired the button for a split second and it still seems to be functioning. Not sure what I should do lol or just ditch out on it? It appears to be working yet but stinks like an electrical fire now. I’m kinda reluctant to use it (I still have an old coil but it was starting to taste funky). Any advice or idea what might’ve happened?  

I bought my Sigelei 100w Plus a few days back and ordered 2 Sony VTC4's on my same order (I'm confident they're legitimate, I've bought some before) to be able to marry them together and use them with my Sigelei. Upon receiving the batteries, I labelled one A, and one B and put them into my charger at the same time (charger was off, put both in and turned it on), one battery is slightly more charged than the other (it's 2/3 bars, while the other is still 1/3). I'm a bit worried about using married batteries, I understand rotating A and B in my Sigelei and charger but will they be the same charge when they're done? They're new batteries and they both went on at the same time yet one of them is charging a little bit faster.

When both of the batteries are fully charged, will they be safe to use and cycle accordingly? I heard about if one battery has even a tiny bit less, the batteries will take an uneven load and it will make it risky. How do I ensure that these batteries remain married?  

So I purchased the eGo One after hearing amazing reviews of the device. I use an Aspire Atlantis on an MVP 3 but needed something more portable for work/going out. I was more than impressed with the eGo One using the .5 ohm coil, and equally so with the 1 ohm coil. The battery life is great, the flavour is perfect and the vapor production is unexpected. However, within 2 hours of using the .5ohm coil, the vapor began to taste burnt, more than on any other wick I have burnt. So until I could get hold of another I used the 1 ohm coil. 24 hours that one lasted. Joyetech said they would send me replacements free of charge, but while waiting for this I went to my local shop and bought another .5 coil. 1 HOUR LATER, it's frazzled. Wether I'm just being unlucky or the device is faulty I don't know, but I am incredibly disappointed. It's not through a lack of priming or using the wrong liquid, I'm an experienced vaper and had fully primed the wicks for 20minutes minimum and was using a 50/50 juice. This device had great potential, but it will be going in the bin for now (except the battery, which even does a great job on my Atlantis)  

I bought two Innokin Endura M18's, and both seem to have problems.
The lights have gone out. There is no way to know the battery power, when they are fully charged, etc.

And now both of them don't seem to vape very well, like there is a air leak. I am using the Innokin M18 tank/coils with them.

Does anyone else use the and how has your experience been with them?  

Hey guys.. i been vaping for a while and not had this hapen before.. i am using a Hugo Vapor Rader and ot has been working with no problems until today... when i go to use it, when i try to fire, it says high atomizer the first time i push fire button followed by low battery (have tried multiple sets) when i press again. If i persevere and keep attempting to fire it works fine as if there were no problem until the next time i go to use the device when the process repeats.. i have taken the tank apart and cleaned and put back but the issue continues.. anyone have any ideas on what is wrong/what i should do?  

i want to buy a new battery but i'm living in korea.
so i decided don't purchase blu battery because it process is rather complicate ,
even i don't want to suffer it again.
anyway fortunately, i found few 510 mini battery on korea ecig webshop.
here is my question
if i buy a new battery then it could be charged in the pack?(charge seat for blu battery)  

I modified a flashlight holster by adding a bit of seatbelt to widen it and work with my Kanger KBOX to wear around my neck and/or holster it to my belt or bag.