Lost My Subtank Mini Rebuildable Rba Deck

So I finally got around to putting a coil on the rba deck...my typical kayfun build, 28 ga @ 1.3-1.4 ohms. Everything looked good, coil tight....raised off the deck...screwed into the ohm meter....weirdness ensues....said 3.85 ohms...took it off, put it back on...said 4.6 ohms....looked to see if the coil screws were tight ...check. both tails tight under the screws...check. The coil deck screwed into the base...yep. No moisture in the base, nope. Put it on the ipv...said 7.7 ohms, then 4.2, then 3.90.............


Put the stock coils in the base, everything normal. Is there something I could be missing in the coil deck??? I got nothing else. No, I had not put the chimney on, so no short there. I may wrap another coil and see....I can only think that something is amiss in that little coil deck....or I am missing something in the build that is obvious. It's a really nice, tight looking coil too.  

so in my pursuit of vaping above 200 Watts I made a fuse 3x24ga gauge wrapped with 36 gauge and I tried three coils. it came out .07 I Vaped it at about 375 watts it was a hot vape but the ohms were very low so I had a problem with power my DNA 250c was reporting 65 amp output so I took that and put in dual fuse 22ga gauge wrapped with 36 gauge I ran that build triple coil I used it at about 250 Watts. what I am trying to do is vape at about 300 to 400 watts with an ohm or .2 to .3. the inner diameter will be 5.5 or 5 mm I'll be using the kanthal core wrapped with 36 gauge and ni80.I'm trying to figure out what my next bill should be to try to vape above 300 watts the restrictions I have is it can't be below point 1 ohm or above .3 ohm I have two aromamizer plus has with the series deck The parallel deck a second parallel deck and a single coil deck. The single coil deck fit 6.36 mm.

I also have the aromamizer titan.

What gauge would you Clapton?

Sent from my HD1907 using Tapatalk  

Hey all, sorry if this is posted in the wrong place but I was wondering if anyone has tried a 24g coil build in the subtank mini rba deck and if it worked or not? Regardless I'm going to build a coil a little later to try and see how it works but I thought I would ask before hand on the odd case someone has tried, I've searched a bit and couldn't find anything, everyone seems to like twisted coils in these. The main reason I'm interested in doing this is because I've never vaped a successful tank with no burnt/dry hits yet so I figure the 24g ramp up time might help settle this problem, at least for me. I'm interested to see the thoughts so please reply  

Hey guys whats up. Well I had gotten the Sub Mini tank, the first tank I got was a dud. I had nothing but issues with it since day one. Coils went bad in 1.5 days both coils, then the rba deck was giving my sigeili issues and errors.

So I sent it back, They replaced it, and I now have Version 2 as they say. This tank has 2 air slots and different Holes in the tank. I used the Stock .5 coil but was just getting wayyyy too many dry hits.. So I went to the RBA deck, been using the coil that came with it, and I have 100% organic cotton. So I been using that, but now I am getting Dry hits with this thing!!! every 4th hit Is Dry!! I have to cover the holes and pull to get teh cotton wet again, and then 4th hit shes dry again.

What is going on here? Anyone else have issues like this? I am really getting fed up with this and ready to just throw it away. What can I do about the situation or why is this happening?

E-juice = 80/20 Clear Liquid all fruity flavors 3MG  

So I know this is feeling more and more like a taboo topic. I have an istick50w, and a subtank mini.

Today at work I do my morning ritual, of connecting the tank, taking a few puffs, and turning it off while in my office.

I just took my lunch break and head into the break room, turning it back on and for whatever reason, my device jumped from 15w, to 50!!!

I know for a fact I turned it off. I always watch the screen go off. There's no way it could turn on in my desk, or anything like that. There's no way I could turn up the watts because it's constantly locked.

I have no idea what happened but I am incredibly mad.

Now my coil is tasting burnt. I've been using it for a day or two, so it was properly primed. But I'm sure going from 15 to 50 just killed it.

It was one of my last coils too.

 

Got no idea what this thing falls into...

The MechLyfe Ratel 80W (8.5V). It uses an external 18650 battery and it uses an RTA build deck. I’m not sure if you can use pre-made coils for it though. You can use it in both DTL and MTL but with MTL it’s loose draw. You can’t adjust the airflow on the fly, you have to take the panels off to make the airflow adjustments.

The build deck looks nice and simple to build on. You might get away with fitting in an alien coil.
 

I am running my Kanger Subtank mini rba deck on .9 ohm (spaced 4 wrap 28awg IIRC) at 13 watts and it is cloudy and flavorful. The OCCs were fine but I prefer the rba I think (even though I'm still a bit of a build novice). Many others seem to run it at 25+ watts and lower resistance. I had it at .5 Ω and ~19 watts was good, had dry hits above 23 watts. Now have dry hits above 15 watts at .9 Ω. I'm still playing around, but this current build/wattage is working awesome.

Other important factors:
Tobacco and vanilla DIY juice 4mg 50/50 PG/VG Organic cotton, standard wick Only had Subtank for 3 weeks Coming from BCC clearos Been vaping for 6 years Used to be mouth-to-lung, doing a lot of direct lung but still switching back sometimes What's your style with the Subtank? How are you running it? What's your wick-style? Dry hits? Wattage? Ω?  

Hi, I have having issues with the kanger subtank mini sucking hot juice into my mouth with the rba deck it doesn't happen with the occ coils please help....  

Just bought the Kangertech Subtank..... Was told I couldn't use my Max VG juice and I needed to buy some of their lower VG juice. I told the guy no thank you, I know what i'm doing and I can make it wick the Max VG.

Needless to say I got home, the STOCK OCC coil, .5 ohm, wicks my Max VG perfectly fine, even with chain vaping.

I ripped the pre-made coil out of the 1.2 ohm OCC head, and built my own .6 ohm coil in it, wicked it with Organic Cotton (Not KGD or Bacon, Just organic cotton from Walgreens) and it wicks perfectly fine with my Max VG.

I built a single coil .7 ohm spaced coil, wicked it with the double tails on each side, cut off to where it touches the deck, but not touching the threads, put the chimney cap on, and made sure the juice channel was free of blockage, and it wicks perfect with the Max VG.

No leaks, no dry hits, running each OCC head at 30 watts, and the RBA deck at 35 watts.

This is the original Subtank, 6ml for OCC and 4.2 for RBA, (NOT THE NEW 7.0mL version).

So let me hear it.... What have you guys noticed or seen about the wicking ideas, why has yours not worked?

WHY DO SO MANY PEOPLE SAY YOU CANT USE MAX VG ON RTA's, especially on the Kanger Subtank????  

Hi all

So I'm currently set up with an iStick 50w and a SubTank (big un) all thanks to you guys im in Vape Heaven.

want i want to ask is this -

My Girlfriend is now getting more into Vaping and hasnt touched a Cigarette in quite some time. she has an iStick 20w and loves it (cos its pink -_- )

but she's not liking the tanks (aspire Viva Nova, one with a cross on it (completely forgot the name) and a protank 3 mini)

Shes tried my subtank AND LOVES IT! she's liking the airy draw and the ultimate flavour.

My question is she likes to vape at around 3.0-3.3V. Will the Istick 20w be able to SAFELY handle the protank nano with the 1.2ohm coil in?

I've told her she may have to up the power abit but other than that she should be fine right?