Just Confirmed

So this phrase is going around and I have literally no idea what people are talking about.

Can somebody please explain to me what the heck a tootie puffer is?  

Hello Been vaping about 2 years now
My setups are Vaporshark Rdna 30 Istick 30 watt and a provari 2.5 and a IPv mini v2 30 watt
So like many others I have been juggling with wattage I currently Use A couple of kanger subtank minis using the RBA and a kayfun v4 I've been all over the place building ohms but have settled on 1.2 - 1.4 ohms BTW I'm not into sub ohms
So after many months of different ohms and watts with the help of steam engine I have found I like my vape at a heat flux of around 175 so to get to this and I can't believe how simple it was I just take the ohms I am using such as 1.2 @ 12 watts = 178 heat flux 1.3 @ 13 watts = 178 heat flux and so on I can't believe it became that simple
So I suppose all it takes is to find what heat flux you enjoy and adjust from there
I never bought that what I have read thru the last 2 years that 14 watts is 14 watts no matter what ohms you use it seems to me there had to be more factors involved
Just my thoughts


Sent from my iPhone using Tapatalk  

Hi guys I got a Sigelei 30w mini + Mini Protank III. The stuff will arrive in like 3 days.

I'm new to this stuff so how many watts or volts should I start using it? Any other noob advice???  

I've been using only twin-18650 mods for some time, and before the shipping ban came into effect, I bought a backup of my most-used mod (a Geekvape Aegis X), but since the 100W single 21700 / 18650 Voopoo Drag X Plus was only $35, I also picked up one of them as another backup.

I vape exclusively on RDA's, typically with a 3mm dual coil twisted build with 24 or 26 gauge Kanthal or nichrome-80. 5 or 6 wraps with 24 gauge, 6-8 wraps with 26 gauge. I typically vape these between 90 and 110 watts.

I did not expect to get a 'true' 90-100 watts out of the Drag X, so I set a target of around 60 watts. I mounted a 3mm dual coil twisted 28 gauge build with 6 wraps, which on my Aegis X vapes great at 60 watts, and very good at 50 watts. It measures at 0.45 ohms.

But on the Drag at 60 watts, it only vapes at what feels like 30 watts on my Aegis. Setting it higher makes no difference either, it seems to 'top out' at ~30 watts regardless of the setting. 60 watts @ 0.45 ohms is only around 11 amps, so I doubt I'm hitting an amperage limit.

I am using 18650 batteries (VTC5A), and it is about time to replace them, as I am only getting around 70% the battery life as I did when new. I will be picking up some 21700 batteries at the same time, which hopefully help with things on the Voopoo.

Does anybody have any good experiences with ~60 watt builds on a Drag X Plus?  

So....been vaping for 6 years.

For the last couple years I was using a Reo with an RBA at .5 ohms and was going through about 12-15ml a day. A friend of mine let me try his sub ohm tank a few weeks ago and I was hooked! The flavor was better than my Reo/RBA setup and the vapor was OMG.

Anyways, I've since bought a couple of sub ohm tanks with an IPV2 Mini, then graduated to a Goliath RTA with an SX Mini M Class. Using the Goliath with a .44 ohm dual coil at 30 watts on the SXM and I'm going through anywhere from 25-35ml a day! This just seem excessive....

Can anyone recommend an RTA that would use less juice but still give me a lot of airflow and flavor? I'm not all about the vapor, although I do enjoy it.

I'm guessing that if you want lots of airflow (I'm a direct lung inhale kinda guy) and a warm, full vape you pretty much have to vape at higher wattages/lower ohms and therefore use excessive amounts of juice...just wondering if anyone else has had a similar experience and has successfully cut down their juice consumption.

FYI, I DIY my juice so cost is not really an issue...I'm a bit concerned that using this much juice every day just can't be good for you.  

I am a confirmed tootle puffer although a chain vaper. My coils are generally 1.8 to 2 ohm and I rarely go beyond 11watts. Even when on a whim I wrap a slightly lower ohm coil I still never go beyond 13 watts. Still I find my drip tips get too hot and burn my lips especially when I use the kraken. I have sores in a couple of places. Is there a way round that. The other day I bought a couple of long ceramic drip tips, the ones normally used for e-pipes but I find they get filled with too much condensation.

What do you guys do? Do you have this problem?  

I'm not that fond of VW because I find most inboard ohm meters are all over the place. It's either low or way too high. I know, the resistance changes as to the voltage applied, but I don't find it so convenient as VV. As for now is mostly vape by taste, and I can never be sure if it's going to be good or mediocre, just depending on the ohm readout. Just now, an 1.8 ohm head Nautilus is reading 2.5 on my iStick 30, 1.7 on my IPV mini and 2.0 on the Sigelei mini. I just can't understand how you can vape on this, I thought it was my rebuildables, but no, it's the onboard ohm meter.  

All of the sudden I wake up today and notice my 510 threading on my sigelei 50w box mod is jacked up. I cleaned the threads on my subtank mini and on my sigelei mod. I then tried screwing it onto my mod and now no matter what I try , there's a gap between the top of the mod and the bottom of the subtank (it's not screwing down all the way and has about a 3mm gap, hence now it won't fire...

I screwed my subtank onto my ileaf 30w and screws in flawlessly, so it's the sigelei threads ...

but I did pay a lot for my sigelei and prefer its hits , I dunno, I usually Vape about 16W on my sigelei And not sure how that translates over to what wattage I should run the eleaf at ?

Also, I just noticed that my spare RDAs will still screw onto my sigelei well..I'm so confused what's up !!!!  

Hi everyone!

Ok, you've seen the term on a few threads now, and you've scratched your head thinking...... "What in the world is a Tootle Puffer?!?!"


You're not alone. Many are wondering. Yet, there are a several people who know exactly what it means, and have smiled their way into the Tootle Puffers Club.


Let's have some fun. Let's find out who actually IS a Tootle Puffer, and let's define it!*




Are YOU a Tootle Puffer? What does that mean!!!







*And before you ask, no, I'm NOT making another spreadsheet!  

Right now I have a cloupor mini and a magma and a subtank. But I'm ready to upgrade. I want to push the ohms lower and the watts up. My mini only goes to 30w but I'm looking to vape maybe 50 watts plus. So I'm thinking around a 70 or 75 watt mod and idk about a new topper. I'm thinking maybe a lemo and some kind of a new dripper. Maybe a plume veil or mutation x. Anyone have any recommendations. Btw I am on a budget.