I just got my god mod today and I was playing around with different builds on my yep clone. I accidentally dry burned a build at 165 watts!!! They got so hot one melted off the post.
So I built a twisted build out of nichrome 60 wire and tried it on a triple series 18650 mechanical box and it melted the coils why won't nichrome work with any series boxes 8.4 volt melted 12.6 volt melted but I can build a .06 nichrome build and run it on my mech tube mod and it handles it I can build .15 and run it at 150 watts on my Sigelei and it handles it but bump up the voltage and it melts don't get it. I ran a .30 nichrome build at 260 watts on a SMY 260 and had no failure of the coil so I'm puzzled why a series mech box desemates the coils?
So I decided to try a 1,6 ohm coil on kayfun v4 clone Tobecco and I am using 28gauge Kanthal with a cotton
wick on a Rdna 30 and its vaping well at 15 watts I have a kanger subtank mini coming in the mail and here goes my question
So the kanger subtank states that with a .5 ohm coil i could vape up to 30 watts but the voltage comes in at like 3.8 volts
I was under the impression that the rdna 30 needs at least 4 volts to work which kinda brings me to my second question
What is the point of of sub ohms? cant i just build a 2.0 ohm coil or something like that to achieve the results as if i was subohming
I am very confused on this
thanks for the replys in advance
Oh yea is a 1.6 ohm coil at 15 watts a normal build or any recommendations for the kayfun v4 for watts and ohms thanks again
I'm about to venture into doing my own builds and I had a silly question. I have watched dozens of videos on how to do builds and have even done a couple builds on some of my friends attys. I have one friend who on all his dual builds he uses two coils with different wraps. For example one coil with 7 wraps and one with 5. Does anyone else build this way? I have never asked him why he does this and in all the videos I've watched I've never seen anyone else do it. Is there a specific reason? Just curious
Somehow, I inadvertently pushed the buttons just wrong today and it went from 7 watts (my usual power setting) to 50 watts (the highest setting). I didn't even mean to push any of those buttons.
I experienced instant burnout and a horrible taste in my mouth and the coil was instantly ruined.
Do people really vape at such high power? If so, how often do you have to replace the coil? And how many ohms are you putting that through? The coil I replaced it with is 1.77 ohms which is about the same as the one I burned out.
50 watts seems so excessive to me that I double-checked and yes, that's what it says it goes up to. Even at 7.5 watts the coils seem to burn out too fast which is why I vape at 7.
I feel like Nigel Tufnel designed this thing. "But it goes to 50. That's 43 higher than 7. So it's like 43 more. So when you're vaping at 7 watts and you want that extra push over the cliff..."
(I'm actually impressed that Nigel could do the math to figure that 50 was 43 higher than 7)
Hey guys, sorry if I post this in the wrong place, but I didn't find a sub forum that seems appropriate.
So, I have a BCV Surfrider clone (hybrid) and it has been working great but all the sudden this last weekend I noticed one of my batteries just stopped working.. not a big deal. So I put in another battery. Still not working. So I was playing around and I noticed that my button got extremely hot. I took the battery out and noticed that it was hotter than I've ever felt.
I was playing around with it to see if something is wrong, but everything seems fine. I accidentally put in the battery backwards and it worked fine like how it used to.
Anyone have any idea what is causing this?
Hey guys,
I recently started playing around with 24g kanthal in a kayfun lite plus clone that I had bought last year and started to notice a serious issue which was that juice would at some point start to look orangish, when I recently opened it up to change the coil to put in a new flavor it was completely black. However when I had previously fired it and had noticed no burnt taste. Any ideas as to what's going on.
Background on build
24g purchased from brick and mortar store
Cosmic Orange BLawesome juice (pinkish)
0.6ohm coil 6 wraps
eleaf istick at 32.2 watts
Cheers
I've been using only twin-18650 mods for some time, and before the shipping ban came into effect, I bought a backup of my most-used mod (a Geekvape Aegis X), but since the 100W single 21700 / 18650 Voopoo Drag X Plus was only $35, I also picked up one of them as another backup.
I vape exclusively on RDA's, typically with a 3mm dual coil twisted build with 24 or 26 gauge Kanthal or nichrome-80. 5 or 6 wraps with 24 gauge, 6-8 wraps with 26 gauge. I typically vape these between 90 and 110 watts.
I did not expect to get a 'true' 90-100 watts out of the Drag X, so I set a target of around 60 watts. I mounted a 3mm dual coil twisted 28 gauge build with 6 wraps, which on my Aegis X vapes great at 60 watts, and very good at 50 watts. It measures at 0.45 ohms.
But on the Drag at 60 watts, it only vapes at what feels like 30 watts on my Aegis. Setting it higher makes no difference either, it seems to 'top out' at ~30 watts regardless of the setting. 60 watts @ 0.45 ohms is only around 11 amps, so I doubt I'm hitting an amperage limit.
I am using 18650 batteries (VTC5A), and it is about time to replace them, as I am only getting around 70% the battery life as I did when new. I will be picking up some 21700 batteries at the same time, which hopefully help with things on the Voopoo.
Does anybody have any good experiences with ~60 watt builds on a Drag X Plus?
Ok I'm hoping I don't get heat for these questions/statements but educating ones self especially with something that is still very new is important to me.
1. Read some articles on how there is second hand vape similar to cigarettes (99% better mind you) what are your thoughts? Vaping may not be as safe as smokers think, research suggests | Society | The Guardian
2. Formaldehyde found in builds running at high watts/voltage? But 0% at low/normal builds, what i can't seem to find is whats considered to high for a Mechanical Mod or even for a V/W, V/V Setup? My normal build for a mech mod is twisted single coil 24 gauge 6-7 wraps, usually gets about 0.28 ohms and single coil 8 wraps of 24 gauge puts out 0.73 ohms on my flavor builds.
Before You Vape: High levels of Formaldehyde Hidden in E-Cigs - NBC News
Trying to find my happy place.......
I have been playing around with ohms and watts more since I got into rebuilding and have found sub ohming changes the flavors too much for me and the throat hit gets a bit harsh.
Tootle puffing does not satisfy my need for thick rich vapor.
Still looking for my version of perfection. I have gotten close with a few higher ohm builds that still get pretty good vapor production, but I just haven't gotten my vape nirvana yet.
Maybe I need to meditate over my builds?
Just a little warning to all who have purchased the Lemo 2- Do not use the wire included in the box.
I was a little worried when i was using the stock coil and noticed it had been turning a green color after a few days of use, not sure if this is the case with all Lemo 2's, but if you notice your wire is turning greenish, just throw it out and replace it. I don't believe this is kanthal, it could possibly be nichrome, but it's properties are not matching up with those of kanthal. My worries were confirmed when I decided to put a parallel 5 wrap coil on my rda with that wire because of my lack of other 24 gauge... Well today when I took out my cotton and dry burned the coil a little to rid it of excess juice, the coil actually deformed and somewhat melted on my rda . I don't know what kind of metal this is, but I'm positive it is not kanthal, this has never happened to me with kanthal, and this wire seems to be of a lower resistance than kanthal. Anyway, just wanted to let ya'll know to be careful with that wire, or just throw it out altogether. Otherwise, the Lemo 2 is a fantastic tank