What Is Your Favorite Single Coil Build On A 3.7 Volt Device ?

I am trying to get the best flavor with the best single coil build.

Objectives:
Flavor Smooth Vapor
Materials:
Kanthal Wire 35mg Nic Salts
I have noticed that either depending on the diameter of the coil or the spacing of the coil wraps You get a different kind of vape hit. It seems like higher gauge wire produces a smoother hit. And then couple that with a small diameter coil build, plus squishing the coil together to remove all coil spacing results in the smoothest possible vapor.

Can anyone confirm my findings? Or does anyone have any tips because I have still to replicate the smooth hit from clearomizer sub tank cartridge's that are non mesh. I am starting to think this is because the cotton is wrapped around the outside of the coil instead of being shoelace through the middle of the coil.  

I recently picked up an infinite origen v2, my first build was single coil 2.4mm and it was not good on flavor, next build was dual coil 2.4mm at .5ohms, it was better on flavor. No matter what single coil build I try the flavor is just not there. Any suggestions on great flavor builds???  

Wondering if this coil has been created before and what it's called or what you might call it if it's not already "titled" a certain coil

It's twisted 26 gauge space Clapton'd then flat ******* between spacing... any thoughts?  

I found an "interim job" this week and decided to reward myself. I was originally stopping by the B&M to get another Subtank Mini as this job involves a 45 minute commute and I'd like another 'bigger' tank to take with me (almost got a regular sized Subtank, but it looked ridiculous on the VF and didn't feel comfortable), but they hadn't gotten them in yet, so as I was standing there browsing (as I always do if they don't have what I'm looking for), they said they got more RDA's in. So I looked, but wasn't thrilled with the one that was suggested first, so someone else suggested my new toy. It looks great on the VF! I already know how to build, but I asked about different flavor builds, so they sat down and showed me how to do twisted builds. They built me a twisted 28g single coil that reads ~0.6 Ohm. Holy cow the flavor! I know, I'm like a little kid discovering the swing set all over again for the first time. lol. So...what do you think of my new toy?

 

I needed an extra 510 drip tip for an atomizer (someone gave a used one with no tip) I had been sharing one from another tank (atomizer... tank is easier to type) so I dug through a box and remembered an old RTA I could steal the drip tip from. Then the memories flooded in... it was a UD Bellus someone gave me (with a warning... "she is evil") I was not put off by this (I like a good challenge) so tried several times to build "the evil one"... no success (it has an extremely small build deck, dual coils sharing the same post holes with tiny screws and no clearance between the coils and chamber) When it did work (briefly) it actually had decent vapor and flavor. I finally gave up... long story but short answer... this tank was my "nemesis" for sure. I even tried the single coil option (came with an adapter to block off one side) still no luck (wanted to throw it in the trash or better yet take a hammer to it) Anyway... what atomizers have you had that you consider your nemesis (evil, vile, stubborn, useless... feel free to use other terms)?
P.S. I know it's futile, but I'm going to try one more time with that "....." (I can hear her laughing at me as I type this)  

Many people may find this funny, but I vape at 5 watts, and I build my coils with a single 28mm wire, 1.5mm ID, and 5 wraps.

I only vape MTL and use kayfun's.

A single 2ml tank will last me most of the day, and batteries close to 2 days.

I just want a cigarette "like' experience to keep me from smoking (have not smoked a cigarette in well over 3 years now), and see no reason why I need anything more out of a vape.

So tell me about you...  

Ok I'm hoping I don't get heat for these questions/statements but educating ones self especially with something that is still very new is important to me.

1. Read some articles on how there is second hand vape similar to cigarettes (99% better mind you) what are your thoughts? Vaping may not be as safe as smokers think, research suggests | Society | The Guardian

2. Formaldehyde found in builds running at high watts/voltage? But 0% at low/normal builds, what i can't seem to find is whats considered to high for a Mechanical Mod or even for a V/W, V/V Setup? My normal build for a mech mod is twisted single coil 24 gauge 6-7 wraps, usually gets about 0.28 ohms and single coil 8 wraps of 24 gauge puts out 0.73 ohms on my flavor builds.
Before You Vape: High levels of Formaldehyde Hidden in E-Cigs - NBC News  

so in my pursuit of vaping above 200 Watts I made a fuse 3x24ga gauge wrapped with 36 gauge and I tried three coils. it came out .07 I Vaped it at about 375 watts it was a hot vape but the ohms were very low so I had a problem with power my DNA 250c was reporting 65 amp output so I took that and put in dual fuse 22ga gauge wrapped with 36 gauge I ran that build triple coil I used it at about 250 Watts. what I am trying to do is vape at about 300 to 400 watts with an ohm or .2 to .3. the inner diameter will be 5.5 or 5 mm I'll be using the kanthal core wrapped with 36 gauge and ni80.I'm trying to figure out what my next bill should be to try to vape above 300 watts the restrictions I have is it can't be below point 1 ohm or above .3 ohm I have two aromamizer plus has with the series deck The parallel deck a second parallel deck and a single coil deck. The single coil deck fit 6.36 mm.

I also have the aromamizer titan.

What gauge would you Clapton?

Sent from my HD1907 using Tapatalk  

I have recently purchased a DNA 40 device and feel like I have lost all my build knowledge!! I am using awg 28 wire if I do 10 wraps on a 2.5mm drill bit I get a reading of around .13 on any of my devices if I replicate the build on the Lemo it comes out .27 or above. What is going on can someone share any light on this?


Sent from my iPhone using Tapatalk  

Hey everyone, I just wanted to post my setup here, nothing to fancy so just take a quick look and feel free to leave a comment or reply.

To kick things off I've got a Seeker Mech Mod by EHPRO. It's a sleek design, all copper, and easy to press button. Little short and thick for those of us who like our setups to look beefy.

Atty- The Tobh Atty. It is a pain in the butt to take apart from the get go but once you get a bit of juice on all the O rings it comes apart fairly easy. Good deck to build on all pre-drilled holes on the three posts 1(+) and 2(-) (Obviously). Deep basin to hold plenty of juice for our drip and drivers safety. My current build is a dual single coil coming in at 0.28 ohms. Using a regular cotton wick.

Juice- "Bliss" made by The Artisan Vapor 100%VG This juice is an explosive flavor of fruits, and for being 100%VG it has a heavy flavor. 39ml bottle runs at 20$ not to bad for a good juice. When I drip with a full basin it lasts roughly an hour, and I heavily use my vape.

Battery- This thing is one of the best right now but I'm still limited on what builds I can do. My 0.28 is safe, however my 0.22 is unsafe (Go figure) ANYWAYS! (Specs) MNKE IMR-26650 3.7(low) 4.2(High) 3500mAh.

So I think that's all. Thanks for reading guess, and questions or comments just drop it down below. Goodbye and VAPE ON!