So I purchased the eGo One after hearing amazing reviews of the device. I use an Aspire Atlantis on an MVP 3 but needed something more portable for work/going out. I was more than impressed with the eGo One using the .5 ohm coil, and equally so with the 1 ohm coil. The battery life is great, the flavour is perfect and the vapor production is unexpected. However, within 2 hours of using the .5ohm coil, the vapor began to taste burnt, more than on any other wick I have burnt. So until I could get hold of another I used the 1 ohm coil. 24 hours that one lasted. Joyetech said they would send me replacements free of charge, but while waiting for this I went to my local shop and bought another .5 coil. 1 HOUR LATER, it's frazzled. Wether I'm just being unlucky or the device is faulty I don't know, but I am incredibly disappointed. It's not through a lack of priming or using the wrong liquid, I'm an experienced vaper and had fully primed the wicks for 20minutes minimum and was using a 50/50 juice. This device had great potential, but it will be going in the bin for now (except the battery, which even does a great job on my Atlantis)
I'm having trouble with my Jem Pen E cig - hopefully someone can help me.
I take the coil out clean the tank and battery area, put it back in with liquid + prime the coil. for about 5 minutes it tastes fine and is vaping as normal. then a really horrible burnt taste comes in which is unbearable to smoke and making my throat hurt.
I take the coil out and clean again, put more liquid. the same thing happens! it tastes absolutely fine again and then gets burnt.
any idea why this is happening ? the device gets quite hot too...
i don't think the coil is the issue because why does it taste fine for a few mins?
I've ordered new coils so going to try that but worried its the device. i've only had it for 2 weeks and changed the coil about 5 days ago.
I've got a Nautilus with a 1.6ohm coil, and an iStick 50w. On the side of the coil it says 3.2v-5v, and I want to know if that's just a guideline or a limit for the coil.
I'm running it at 4.8 volts, but I get better flavor and vapor at 5.5 volts. There are no wicking issues or burnt taste at 5.5v, but I don't want to damage the battery or the coil. Any advise would be great thanks!
So I decided to get another clearomizer and the Donner by Amigo Itsuwa is what I got to replace my Aspire Atlantis.....
So here are my thoughts on it and it's just My Opinion:
Holds 4mls of juice - holds more juice so I'm not refilling my tank 2-3 times a day
.50hm Coil head is cotton & Kanthal wire & a wire mesh around the opening for better wicking ( You can use Atlantis coil in this thing and it's better in this tank then it is in the Atlantis) It comes with 2.
There's no notches or trying to center the coil head. It sits in the Clearo and just sucks juice lol
Great Flavor sub-ohm - The flavor you get from this is amazing, I was a little taken back bc I chose a sour raspberry and it really was more sour tasting then in any of the other tanks I had the same juice in
I personally like the drip tip but it's not for everybody
Adjustable air flow control is a wide slot - It's a slide around, but the draw from almost closed to full open is nice any way you wanna vape.
Vape production is great I use 10/90vg - 20/80vg
There are some things I don't like about this tank...
Priming the coil is a process - on a fresh coil the directions state to drop a few drops onto the coil, then once tank is filled let sit for 1-2 minutes prior to use. On your second fill of the clearo you have to let the coil sit for 2 minutes b4 use....I kinda wanna fill and vape, not fill and wait
Holding 4mls of juice is great, but if you can't vape 1ml of juice at the bottom of your tank it sucks. You can't vape the last ml of juice because the coil head sits to high so it can't wick the remaining juice.
I did find that when I put the Atlantis coil head in that the wicking was alot better then the coils that it came with, now this could be bc I am using a high vg juice.
So let's talk price....I bought this at a B&M so I paid A LOT more then what I've found online.
My price was $45.00
I have found these online for as little as $23.00
and for this price I would probably buy it again, not for $45.00
Iv'e been vaping on this for about a week now, I've gone through 2 coil heads in 4 days & now put the Atlantis coil head in it and am having better luck with it.
So there's my thoughts on my new clearomizer.
I was borrowing my bro's Atlantis, for awhile. I put a new coil in it, a couple days before I returned it. It was hitting great. When I give it back, we dump the juice back in a bottle and put the tank back in its original box. About a week later, he sells it to my brother in law. Here's the weird part - we fill up the tank, assuming the coil needs no priming, and fire it up. It seems to be weak on vapor production. It has the nice crackle/pop, and there is no burnt taste or dry hits, but it just isn't producing the volume it used to.
Is this because it sat for a week?
Two issues I wanted to fix. The first is the battery run time using the low ohm coils. Second is when the e-liquid gets to the top of the sub ohm coil housing in the Kangertech I've noticed a lot of dry hits when heavy vaping, ( I like a higher VG juice. ) I would find myself closing the air intakes and sucking hard to get the wick saturated, ( a real pain in the ***. )
NOTE: I like an airy hit and run the air intake ports full open.
So here's what I did.
I've drilled the wick holes out to 3.5mm in the Kangertech coil housing. Then built a 1.1 ohm coil with 4 strands of 32ga. kanthal, ( twisted together first ), 5 wraps around a 3.47mm screwdriver. The coil was very springy to work with but got a bit stiffer after torching t closed to 1/4" width using adjustable tweezers. I used regular ball cotton for the wick in this experiment. The coil came in at 1.1 ohm.
Primed the wick and filled tank with a little bit of juice, just below the top of the coil housing.
All I can say is WOW. The first 10 hits taste a bit crappy but after the break in, WOW.
Taste and vapor production are great. There's a bit of crackle but no pops. Crackle I don't mind, Pops I mind. The ClouporT8 counted 75 hits and now the e-juice level is just above the wicking ports by a hair and still working great with full open air intake ports.
I will add post after I've used this set up for awhile.
Curious what other think!
VapeOn
I'm almost two years into vaping and it has been great.
I've been using a VW Ehuge 35 watt 26650 mod with a Kanger Subtank. Its huge and heavy but the battery lasts a long time. Also been using an Innokin Coolfire 2 with a Gladius tank.
Figured it was time to upgrade. Been watching several review videos to see whats out there. A lot of new sub ohm tanks and they all seem pretty good.
I've never had a box mod and figured it was time. Bought a Cloupor T6 recently to put my Subtank on. The T6 is supposed to be a 100 watt device. The Kanger coil only goes to 30 watts so no big deal there.
I really like the T6. Pretty small for a 26650 mod. Surface is slippery though, need to get a wrap for it. Butons are nice any clicky. The battery cover has magnets which is nice, no screw driver needed. Feels solid and the internals are clean. Its thick and the 25mm Subtank fits nicely on it.
Recently after watching some videos, I came across a new kinda unknown Sub Ohm Clearo. Its the Freemax Starre Sub Ohm. .5ohm or .25ohm coils. Mine came with the .5ohm. The .5ohm is rated 20-60 watts and the .25ohm is rated 20-100 watts. Reviewers were all impressed with the vapor and taste of this device. So I ordered one.
Wow, OMG, this Freemax Starre rocks. Blows away my Kanger Sub Tank in vapor production and flavor. Holds 5ml and the air holes are huge. Surgical Stainless Steel and Surgical Cotton used in the coil. Amazing.
After some more research, I discovered the Cloupor T6 really doesn't put out 100 watts. Well, that makes sense as its only a single battery device.
So went to the local vape shop today and bought a Sigelei 150 watt to put the Freemax Starre on. Will order some .25ohm coils soon.
Lovin the Sigelei so far. Magnets on battery cover, comes with a silicone gel case, nice clicky buttons, takes 2 18650. Its taller and wider than the T6 but not as thick. One thing it lacks that the T6 has is a USB charging port.
The Freemax Starre fits perfectly on it. The Kanger Sub Tank is wider than the Sigelei but fits perfect on the T6.
Really enjoying both of these box mods.
A few pics
I have got this device occationally from the giveaway hold by Joyech and have used the device for one week. It's really great for me as a new vaper. The EN coil lasts a whole week and now it still tastes great, maybe the AST-STEEL inside works. What I appreciate the best is the device does NOT leak like other vape pods. Just a good suggestion for new vapers like me .
Hey there guys, new here.
I have a Vappresso Revenger Mini kit and I have upgraded my tank from NRG SE Mini tank to a "Geekvape Z Sub Ohm tank(Much Larger Tank)". Because I wanted to taste more flavor and still blow lots of clouds in the air with my vaping device being fairly cheap.
I put a New Geekvape Z series coil 0.4ohm 50-60W because I burnt my original 0.2 Ohm coil , I wont talk about my previous coil. I'm getting 2 problems here.
1. I'm using 60W, normal setting and every time I vape or inhale I get a taste of E-Liquid in my mouth. However its blowing perfect clouds and still getting an amazing taste but its just that the liquid drops in my mouth. I just want to spit it out every time. How do I fix that problem?
2. The other thing is if I use Higher Wattage and High settings the liquid pours out of the air flow and starts leaking and backspits in my mouth.
(Before I vaped with new coil)I put the new coil in, I soaked it for 10-15mins, while I fill half tank of E-liquid which is 0.8Ng/0.2PG. Then I inhaled 3-4x with no button pressed. Then I vaped to test, still leaking. I set the vape to 70W and high setting then blow downwards into the device 5-6x. All I was trying to do is desaturate it. My results got better didnt notice much of a leak but I still get a little bit of liquid in my mouth. If you can help me out here, I would much appreciate it.
Thank you and kind regards
Tuatara Vaper
I'm new to vaping. I've went through 3 coils barely using them.
My issue is: When I first install the new coil and add the liquid, it produces vaporizes just fine. It seems like when I set it down for an hour or so, and go back, it still produces good vapor. But after a bit, if I set it down after vaping, and go back, it produced no vapor no matter how much I puff it. It seems like if I unscrew the part where the coil is, and run it under water, and then let it dry, and replace it, then add e juice, it'll start producing vapor again. But it seems like as soon as I set it down for a bit, and pick it back up, there's no vapor and I wash it out again, etc then it works, but eventually just stops producing vapor altogether u til I replace the coil.
What's going on here? am I doing something wrong? Do I need to adjust the coil some how? I've bought brand new coils and barely use them and this happens. Is the coil just getting gummed up? The coils don't make vapor after so long, and the usage doesn't even equate to a full day, maybe an hour or so.
I'm just breaking in my Nautilus on my Aspire battery, as of yet I expected a bit more vapor production from this set-up at least 2x more than my Triton.When puffing on it frequently, it runs a bit hot even with the 1.8ohm coil.Eiether the Nautilus or the battery likes the 1.8ohm coils better than the 1.6ohms why is that?I also experienced leakage and gurgling. Once I put a new coil in, that went away. I'm just thinking how can I get a bit more vapor production.It's better than my Triton but not by much.Is it the battery?