It was only about 5 feet to a hardwood floor, but when I looked down and saw two pieces lying there it caused a bit of panic.
I'm building a staircase in a new house and I leaned a little too far over from the landing with the rig in my shirt pocket. I really need to find a good holster for this thing.
After finishing what I was doing I scrambled down to assess the damage: the tank section of the nautilus had separated from the knurled ring just below the AFC ring. It's a friction fit set-up, and after cleaning the juice and sawdust from the parts I was able to tap everything back together with my hammer. I pushed the button on the Provi and nothing happened. Pushed the button a couple more times and I was back to vaping again with no leaks.
The owner witnessed the whole episode, and there wasn't even a dent in the finished oak flooring. He laughed as I cleaned up a couple of juice spots where it hit and watched me put it back together with a hammer.
I'm not usually this lucky.
Big shout-out to the makers of both products.
I've got a VTR that i was using with an aero tank, but was burning through coils like every 4 days. Local vape shop recommended the nautilus mini since that's what the owner uses with the same juice I use. Doesnt quite fit with the VTR ring, but they showed me how to screw the base in and just pop it in that way. Cool, no problem right? Yeah right.
I go to refill and i cant get this ....ing thing off at all. The 510 connection is not stuck in to the device, but the bottom ring to unscrew the glass part is just not budging at all. So now I basically have a inert device and tank that cannot even be used and I'm out 52 bucks in total for this damn tank and coils.
The protruding collar on the hinged cap, where the drip tip is pushed onto, has a perished o ring. There are two tiny o rings here and the perished one means my drip tip falls off. I am not sure what I need to order to replace the o ring. Could someone with more knowledge than myself suggest to what I might need please? I am in the UK.
hey guys. i have an ipv3. a couple days ago i asked my friend to screw the back plate on while i was busy doing something else. he somehow managed to tighten the screws so much that the areas of there back plate around the screws got pushed in and now there are small gaps between the back plate and the rest of the device. i tried countless times to straighten the areas out but nothing is working. does anyone know where/how or if its even possible to purchase just a new back plate?
Dang i am lazy...and ill tell you why. i got frustrated building today, so i when to my little vape shop (50 feet away) and got myself a kanger subtank... and guess what, i freaking love it. i have only dripped like 15 times today on my Kennedy, but im using a tank now, and i don't care, probably because i hate pulling over in my car just to drip, but now im being lazier then poop, i haven't even got out of my lawn chair to go grab some juice...maybe its temporary, but right now im in total heaven.
Chasing the clouds, until i fall back onto the ash of earth... maybe its the dry cotton
I'm only on day nine with my new MVP3 and Nautilus tank (started out with the 1.6 BVC) and I'm down here... Yesterday as I was vaping my MVP shut down and wouldn't turn back on. I had just full charged it but tossed it on the charger anyway and it came back on. Took a couple of vapes and BAM, down again... Put it on the charger again and it came on again but this time the display was flashing two dashes in the ohms section.
So, I switched out to the other head that came with it, had a few vapes and WAMO, down again. Plugged it in, came back up, couple of vapes and down again and again this other head now flashes the two dashes in the ohms section. Now here's the weird thing... When I popped the second head on it read 2.3 ohms. I didn't think anything of it at the time, being new and all, but when I just went to confirm which head I used first and second I read the stamp on the second and it says it's only a 1.8 ohm head.... Another strange thing is that as I was vaping on this second head I changed the watts to improve the vape after a couple vapes and I noticed it read 2.5 ohms, then after a few more vapes it went down with the flashing dashes.
When I took out the second head I notice there is juice in the very bottom of the bottom hardware, where the head is screwed into. I'm assuming this means it was flooded, but being a rookie I could be wrong. At any rate.... I'm not happy vaper right now In hind sight I realize I should have bought some extra heads, but again... Rookies make rookie mistakes right In my defense though, the guy at the shop said I should have been good for a month with what I had bought so I thought I'd be good. I uploaded a quick video to show the MVP3 display and the bottom hardware in case it was needed. You can see it he
So now the questions... What would cause two new heads to die like that, or are they dead? Would it be a head problem or a problem with the MVP3? Am I correct regarding the fluid in the bottom hardware being a result of flooding, and if so what would have caused the flooding and could this have been the cause of the dead heads? And finally... What type of wire can I use to rebuild the heads? I've been reading a lot and watching a lot of videos on rebuilding over the past month or so and hear about nichrome, kanthal, and caplan... Does it need to be a specific type of wire or can I use some wire that I have here that I used for other purposes? Maybe an old guitar string? LOL
I'm desperate here.... I need my vape!!! I don't have the cash to buy new heads until around the 18th of the month and there's a carton of stinkys in the fridge and I do NOT want to resort to them if I start going bonkers Any assistance at all is greatly appreciated.
I've been vaping with v4l and v2 e-cigs for a couple years mostly the ego style ones. I love messing with all the technology I have and I'm very hands on so I figured I'd stop limiting myself. I bought a Sigelei 100w Plus, Kanger Sub Tank Mini, and a Mutation X V3 RDA.
WOW
I feel stupid for not doing this earlier. I've been vaping 12mg for a couple months now, but bought 6mg for the Sub Tank and RDA and that is even too strong! I diluted it with 100% PG to make it 3mg and it is much better. I couldn't be happier. No dry hits.. no leaking... all the problems I've dealt with over the past couple years are gone and I'm experiencing vaping like never before.
Success!!
Plus I finally convinced my GF to start vaping on New Years Eve and she hasn't looked back. She's using the V2 Pro Series 3 which she loves and we even found some really good house made flavors at a local vaping shop that we really liked. She got cotton candy and I got cigar. I didn't think a vape shop would have juice that good and they even made it fresh right in front of us. To my surprise no steeping required!
Alright I'm rambling. I will leave you with this pic.. and to all you musicians out there that is a ART Pro MPA II preamp with genuine Telefunken tubes from the 60's.
20150316_191947 by joshfiricano, on Flickr
Not sure if this is the right place to post this. Received a silver istick 50 yesterday and a black one today. The black one is good but the silver one will stick if the button is pushed on the bottom part of the button and it'll keep fireing since its stuck. I can get it to release by manipulating the button. Is that something the company will take care of??? I do like the battery!
Thanks
Chris
International Travelers
I am now in the US and I am going back to the Philippines for about a year.
I have a couple of VW box mods and a mech. tube mod along with 3 or 4 various atomizers. I also have a bunch of 18650 and 18500 batteries along with a couple of those skinny EGO style Twist batteries.
Since I make my own juice, I have some large bottles of VG and some 60mg Nic unflavored PG base, along with some bottles of flavorings.
I am thinking that everything I have goes into the checked bags except for the batteries which go in carry-on luggage ... does this sound right to you?
One thing else ... If I have a small EGO Twist battery with a small Kanger Aerotank Mini on top of it (for vaping at the airport once I get into Hong Kong), do you think I would have any problem with airport security if I put that in the TSA tray along with my other carry-on junk that's in my pocket before going though the metal detector? ... The Aerotank Mini in my pocket would have a little juice in it.
Thanks,
I have had a lot of mis fires on my Smokless Owl 25.00 squonker and had to press down extra hard
and sometimes side ways to get it to fire.
I just done some contact cleaning and scraping on the Smokless Owl Button.
I took my wifes Emory board finger nail file thingy and depressed the firing button and held it depressed and rubbed it
across the firing pin and then took a small jewlers screwdriver and scratched it back and forth across the end of the pin and
did the same thing to botton ground pin.
I noticed some black color on the end of the firing pin before I started this cleaning process.
I gently took the screw driver and scratched back and forth across the positive and negative end of the battery just to
take any small film or oxidation from the ends just to make a better connection.
It seems to fire now just like it should with no MISFIRES---mod is now perfect !
Hi friends. It's been awhile since I posted a thread and thought this might be a fun topic. I will go first. There are a couple things I really look foward to regarding my vaping. The first thing is when I get a new RBA. I can't wait to get in and build that new tank. I track the package and it's like Christmas when it arrives. The second thing is if I order a new juice! I usually make my own juice but I will also buy a couple each month. Oh I can't wait to break into that new bottle of juice!! Those are a few of my favorite things. How about you??