I don't know if anyone has issues with their protank 2 but I hear a lot more negative than positive on them. I was messing with one of those bootleg ones and I couldn't figure out why it kept on leaking. Now just yesterday a friend gave me his protank 2 and Im guessing it was because he was tired of it leaking. When I first took it apart I took all the pieces off and connected them all again one by one making sure it was air tight as I added each piece. Everything was air tight until I got to the coil. I was taking a drag off it and it immediately started leaking and I was like why the heck does it do that? I noticed that it was leaking from between the coil and atomizer where the two little airholes are. What I did to fix this was take an old coil and gently pull off the little silicone ring (above where it says the ohms and below the wick) then I dropped it into where the coil meets the atomizer. After I just screwed in my coil and it works perfectly. No leaking whats so ever! Very good cloud production so far I recommend trying this if you have one. Sorry if someone already wrote this but I did a lot of looking around and never found an answer. Also didnt know where to post this so I apologize if this is the wrong section.
I know, I know... this topic has been discussed to death. And, I am in the process of searching now.
I have a TFV8 tank that started leaking a week or two ago. I tried all the usual tricks (empty and clean all parts, don't over tighten, replace o rings, etc). Nothing helped. After a few days of covering the mod with a paper towel everytime I took a drag, I decided to buy a new tank. The new TFV8 arrived yesterday afternoon, and after checking it out and filling it with juice, it is doing the exact same thing.
We are not talking about a drop leaking here and there, it is leaking the whole tankful in less than two hours.
Any suggestions?
Thanks!
Sent from my SM-G965U using Tapatalk
I have a problem with the aspire atlantis leaking and its going in the drip tip and i see some of it coming out the air flow holes ived taken apart everything and cleaned and dried it for 2 days and it happened again. I made sure the coil was securely twisted on the bottom piece. Anyone know how to fix this?
So I finally got around to putting a coil on the rba deck...my typical kayfun build, 28 ga @ 1.3-1.4 ohms. Everything looked good, coil tight....raised off the deck...screwed into the ohm meter....weirdness ensues....said 3.85 ohms...took it off, put it back on...said 4.6 ohms....looked to see if the coil screws were tight ...check. both tails tight under the screws...check. The coil deck screwed into the base...yep. No moisture in the base, nope. Put it on the ipv...said 7.7 ohms, then 4.2, then 3.90.............
Put the stock coils in the base, everything normal. Is there something I could be missing in the coil deck??? I got nothing else. No, I had not put the chimney on, so no short there. I may wrap another coil and see....I can only think that something is amiss in that little coil deck....or I am missing something in the build that is obvious. It's a really nice, tight looking coil too.
Hi all,
I have used this pipe for a long time: 5pc 1.8ml Vision V.Tox BBC Bottom Coil Changeable Tank Cartomizer
it is leaking from time to time and taste burned after about a week use.
I use this juice: 30ml Dekang E-Liquid E-Juice VG Based with 21 flavor, DeKang eLiquids
DK-4.
Can anybody recommend a new ecig for me that is not leaking, not too expensive, and just work well? I did not follow the ecig evolution this last years
If anybody have any opinions about that ejuice i use please share. (Quality?/bad for health?)
Thanks
I haven't been having much luck with the two egrips I ordered. The first had broken plastic on the inside (little bits of plastic were caught in the threads, and had probably fallen into the tank). Number one is on its way back to the vendor.
On number 2, the atomizer base won't sit flush with the bottom of the device, and I think it's causing all the gurgling and leaking (e juice was also leaking out of the bottom of the device). I tried taking off the atomizer head and reseating it, and that didn't work. I'm hoping a new base might fix this problem. Any ideas?
Both devices are brand new. When I ordered the first one, I wasn't aware that it was available in a wood finish, so I ordered the second one.
Hello everybody,
I have a question about Sub Ohm Tank. Does every sub ohm tank has the leaking problem? I tried some sub ohm tanks. It has leaking problem more or less.I ask some people, they told me that such big tank has the leaking problem, and we can't avoid it. Is that true?
Does old coils have any negative affects?
I typically burn off the gunk on the coils and put it through a good rinse then change my wick every few days. This was especially true when I'm using standard kanthal on the Protank.
I recently switched to a Solomon 3 using claptons. I find that there is very little gunk on the coils, I still burn off what I can before replacing the wick. I usually change the coil every week and one wick in between. On this one however, I'm 2 weeks on on the same coil and had only replace my wick once using the same liquids that I normally use on the Protank.
What I notice is the vape isn't as smooth as if I were to put in a fresh coil. I think I just answered my own question but what do you guys have to say about it?
I am having problems with my Hellvape MTL, it is not delivering a good flavor and has juice leaking through the airflow, I am currently using the 1.2 ohm coil that comes with the atomizer, I use juices nicsalt 35mg. I use the 3 holes and airflow in the 4 to 12-14w.
Hey there guys, new here.
I have a Vappresso Revenger Mini kit and I have upgraded my tank from NRG SE Mini tank to a "Geekvape Z Sub Ohm tank(Much Larger Tank)". Because I wanted to taste more flavor and still blow lots of clouds in the air with my vaping device being fairly cheap.
I put a New Geekvape Z series coil 0.4ohm 50-60W because I burnt my original 0.2 Ohm coil , I wont talk about my previous coil. I'm getting 2 problems here.
1. I'm using 60W, normal setting and every time I vape or inhale I get a taste of E-Liquid in my mouth. However its blowing perfect clouds and still getting an amazing taste but its just that the liquid drops in my mouth. I just want to spit it out every time. How do I fix that problem?
2. The other thing is if I use Higher Wattage and High settings the liquid pours out of the air flow and starts leaking and backspits in my mouth.
(Before I vaped with new coil)I put the new coil in, I soaked it for 10-15mins, while I fill half tank of E-liquid which is 0.8Ng/0.2PG. Then I inhaled 3-4x with no button pressed. Then I vaped to test, still leaking. I set the vape to 70W and high setting then blow downwards into the device 5-6x. All I was trying to do is desaturate it. My results got better didnt notice much of a leak but I still get a little bit of liquid in my mouth. If you can help me out here, I would much appreciate it.
Thank you and kind regards
Tuatara Vaper
I've been out of the small scene for awhile, relying solely on dripping or my latest journey...searching for the ultimate sub ohm tank.
Anyway, my wife has been dipping her toes back in the vaping waters, and I have a Tatroe Tank set up for her on a iStick 20W. The problem she's having is leakage from the coil. We've already got a number of Kanger Protank 3's in the collection...but they are prone to leaking.
What is out there now, tank wise, that offers 1.8 ohm or so range that is pyrex and doesn't leak? Pyrex or SS is a must, as she like high cinnamon juices such as High Caliber's Flame Thrower. She also vapes as if she's smoking...mouth to lung hits. She likes the tight draw that mimics a cigarette, and would rather have the smaller diameter drip tips like those on eGo and Evod style tanks