Non Sub Ohm Tank Recomendations

Hey guys,

I originally posted this in the hardware specific section but haven't gotten any love so here goes...

I have been off real cigs for a few months now which I'm super happy about, no desire to go back. I kicked the habit with the aspire K1 Ego tanks and since upgraded to Nautilus mini which I enjoy, I'm primarily mouth to lung hitter. In between the two tanks I was sold an Atlantis by a local B&M, the guy said most buy a Nautilus mini then upgrade to Atlantis anyway so he said it would save money. I couldn't really get into it taking lung hits and still really don't enjoy it but am wondering if my technique is off?

I tried 12mg juice in there and it was really rough, I've since dropped my nicotine to 6mg across the board, and tried that in the Atlantis, it gives a harsh mouth and throat feel if I try to lung hit, I also get the same experience if I use 0mg juice. I've tried MtL hits and it doesn't really produce any vapor. Attempting lung hits I've tried all wattages from 15-30W with same results, also I keep the airflow all the way open. I try and inhale deep and quick thinking more airflow might 'dilute' the vapor and make it feel less harsh. Also this is Atlantis1, and I've only tried max or 100%VG juice.

What technique/settings do you guys use and what should it really feel like doing lung hits on this tank? When he sold me the tank I used it once in the shop and it felt very very smooth on the inhale and smooth on the exhale as well as very dense and tasty and pleasant, for the life of me I can't replicate it. Alternatively, is there a tank or RBA/RTA/RDA I can try for MtL hits that will produce that really dense vapor feel?

TIA for your help, I know it probably sounds like a newbie question lol 'how do I use my tank' but I am stuck!  

Starting from a clean - authentic nautilus mini - with a brand new 1.6 (or 1.8 it makes no difference) coil (coils also verified as authentic).

1. Turn tank upside down - with tip removed and fill with juice.
2. Take base unit and set so no air holes are open.
3. Put a tiny bit of juice around the o ring of the base unit (i get the issues if I do this or not)
4. Put 2 small drops of juice into the coil (I get the issues if do this or not)
5. Screw the coil into the base unit (as tight as you can comfortably get it without going past the obvious stop point and damaging something)
6. Screw the coil/base unit into the tank.
7. Turn nautilus mini correct way up.
8. Move air hole to a middle setting.
9. Take some primer puffs with no power.
10. Leave standing for 5-10 mins.
11. Begin vaping gently at 6 watts - moving up slowly to 10.

Ive tried all types of juice - both high VG and high PG and in-between. Invariably at some point i start to get the gurgle. Ive tried the following fixes:

1. Using a paper towel blow gently out of the air hole to get rid of juice - doesn't work - if i kept on blowing id blow the whole tank of juice out.
2. Take the unit apart - most times there will be juice in the base unit underneath where the coil sits - dry this out - dry the coil off and repeat from step 2 above missing out steps 3 and 4. - this sometimes works but its a temporary fix.

There seems to be no pattern to the problem. Sometimes the gurgle starts as soon as ive changed the coil - sometimes its ok for a week. I have 2 units and 2 spare tanks and have rotated them all using the above method - still get the issues.

I have actually never experienced the burnt taste or reduced draw because Ive always got sick and binned the coil before that point.

I am vaping generally at 9.2 watts - but have tried as low as 7 and as high as 13 - it makes no difference.

I don't draw hard - I cannot understand why I keep getting juice in the air chamber - its not a problem with a "dud coil" unless they are all intermittently dud coils - they are all authentic aspire and I've bought them from different places - so its not a dodgy batch issue - the rings are all the correct way up - I have spent hours and hours researching to try to fix these issues - and cannot for the life of me maintain a stable nautilus mini.

Can anyone save me from madness and tell me what Im doing wrong - Im tending towards a conclusion of all nautilus mini components are junk at the moment.

Many thanks in advance  

Hey there guys, new here.

I have a Vappresso Revenger Mini kit and I have upgraded my tank from NRG SE Mini tank to a "Geekvape Z Sub Ohm tank(Much Larger Tank)". Because I wanted to taste more flavor and still blow lots of clouds in the air with my vaping device being fairly cheap.
I put a New Geekvape Z series coil 0.4ohm 50-60W because I burnt my original 0.2 Ohm coil , I wont talk about my previous coil. I'm getting 2 problems here.

1. I'm using 60W, normal setting and every time I vape or inhale I get a taste of E-Liquid in my mouth. However its blowing perfect clouds and still getting an amazing taste but its just that the liquid drops in my mouth. I just want to spit it out every time. How do I fix that problem?

2. The other thing is if I use Higher Wattage and High settings the liquid pours out of the air flow and starts leaking and backspits in my mouth.

(Before I vaped with new coil)I put the new coil in, I soaked it for 10-15mins, while I fill half tank of E-liquid which is 0.8Ng/0.2PG. Then I inhaled 3-4x with no button pressed. Then I vaped to test, still leaking. I set the vape to 70W and high setting then blow downwards into the device 5-6x. All I was trying to do is desaturate it. My results got better didnt notice much of a leak but I still get a little bit of liquid in my mouth. If you can help me out here, I would much appreciate it.

Thank you and kind regards

Tuatara Vaper  

Imagine your self filling an RTA with fresh juice, only to have the worst vape you can endure as you cough up a lung. No its not a dry hit. Do you blame the juice or a clogged up coil? In this episode, I will take a short journey and explore to a better vape.


After a week of chain vaping, over 50ml of juice, a mix of 3mg and 6mg Nic, the rayon wick has finally given up and no longer produced a clean vape. After visual inspection, the coil and the wick has indeed had a significant build up from juice. To the point that I could no longer see wick material between a spaced coil.

After discarding old wicking material and cleaning the coil, i wicked an RTA with fresh Rayon and filled it with juice. My favorite tobacco juice has come a live, i can now take long and deep direct lung hits with enjoyment. My taste buds are intoxicated, as my lungs fill up with smooth and silky vapor with every inhale.


Keep an eye on your coil by visually inspecting it on daily basis. Trust your body and your taste buds when a juice no longer tastes as it should. Re-wicking your RTA/RDA on regular basis or every few days, will help you eliminate many concerns and issues that you might be having with juice flavor or vaping experience.

It only takes ten minutes to rewick, and in return you will continue to enjoy many hours and days of pleasurable vaping experience.


Good Night.  

I only have this problem with one juice flavor. It has to be the juice. Same tank and setup as all my others. I have a fresh coil and tank, load it up, and in less than a day my coil is gunked up and turns my clear juice dark brown. Is this safe to vape? It's annoying having to finish it and rinse my coil. Usually I can just fill my tank/top it off without worrying about cleaning it all. Anyone else have this issue?  

Hey guys whats up. Well I had gotten the Sub Mini tank, the first tank I got was a dud. I had nothing but issues with it since day one. Coils went bad in 1.5 days both coils, then the rba deck was giving my sigeili issues and errors.

So I sent it back, They replaced it, and I now have Version 2 as they say. This tank has 2 air slots and different Holes in the tank. I used the Stock .5 coil but was just getting wayyyy too many dry hits.. So I went to the RBA deck, been using the coil that came with it, and I have 100% organic cotton. So I been using that, but now I am getting Dry hits with this thing!!! every 4th hit Is Dry!! I have to cover the holes and pull to get teh cotton wet again, and then 4th hit shes dry again.

What is going on here? Anyone else have issues like this? I am really getting fed up with this and ready to just throw it away. What can I do about the situation or why is this happening?

E-juice = 80/20 Clear Liquid all fruity flavors 3MG  

It all started as I was bored one day and decided to drop by the local vape shop and see what they had for sell. Silly me I bought a "pod mod" to see what all the fuss with the devices was about.

Enter the mod on the far left. A "pod mod". I don't recall what it cost me but it was small and light and not very expensive and the sales person claimed "it won't leak" so I figured - what the heck, I'll get it and make up some 'salts' juice and try it out.

While it was fairly easy to fill and the sales person was right, it did not leak. It did suffer from a number of 'issues'. Namely dismal output, battery life and juice capacity. Did I mention that the "flap" to get at the microUSB connection for charging was challenging? While I tried to make use of it while I enjoyed my morning coffee after a few weeks of ether running out of juice or battery at just the wrong time I started looking else where. However now that I had 30ml of 50mg juice mixed up I though I'd 'upgrade' my "salts dispenser".

Move to the setup in the middle, a Nautilus mini clone (with aftermarket RBA) and a iStick40. While the RBA is downright painful to build on I left the 1.4 ohm Kanthal build on it and filled the 2ml tank with the 50mg juice. The iStick40 is said to have a 2700mah battery (and optional TC with NI coils). The iSticks have their USB ports on the bottom. So with the tank filled up and the iStick charged up I again went about my business. This setup was a vast improvement over the 'pod mod'. Better (but not great, after all it is a Nautilus mini) output, longer battery life and more juice. It felt good to be able to grab some gear out of my stash and put it to use. The setup did have its downsides, namely the filling of the tank. Tanks of this era are filled by unscrewing the bottom+coil/atomizer out of it and squeezing juice directly into the upside down tank and then screwing it back together. While I had a dozen or more of this style of tank in use in my early vaping days, I've grown accustomed to easy top fill tanks so started thinking that I could do better so back to the stash I looked.

Enter the setup on the right. While the mod itself is fairly new (Dicodes 21700) the tank is a eLeaf "Lemo2" (only slightly newer vintage then the Nautilus). This setup gives me 3.2ml of tank, even higher output, top fill ease, longer battery life and TC of the coil. The three drawbacks of this setup are that its MUCH larger and heavier than the pod mod that I started out with and the only way to get new energy into the mod is swap batteries. Last and importantly (for those that like to use coil wrecking flavors) is that the only way to service the coil is complete disassembly of the entire tank to gain access to the coil. (not much of a worry when vaping pure unflavored juice).

This is the setup I've been using while enjoying my morning cup of coffee though. Just all part of a evolution.  

So I decided to get another clearomizer and the Donner by Amigo Itsuwa is what I got to replace my Aspire Atlantis.....
So here are my thoughts on it and it's just My Opinion:

Holds 4mls of juice - holds more juice so I'm not refilling my tank 2-3 times a day
.50hm Coil head is cotton & Kanthal wire & a wire mesh around the opening for better wicking ( You can use Atlantis coil in this thing and it's better in this tank then it is in the Atlantis) It comes with 2.
There's no notches or trying to center the coil head. It sits in the Clearo and just sucks juice lol
Great Flavor sub-ohm - The flavor you get from this is amazing, I was a little taken back bc I chose a sour raspberry and it really was more sour tasting then in any of the other tanks I had the same juice in
I personally like the drip tip but it's not for everybody
Adjustable air flow control is a wide slot - It's a slide around, but the draw from almost closed to full open is nice any way you wanna vape.
Vape production is great I use 10/90vg - 20/80vg


There are some things I don't like about this tank...
Priming the coil is a process - on a fresh coil the directions state to drop a few drops onto the coil, then once tank is filled let sit for 1-2 minutes prior to use. On your second fill of the clearo you have to let the coil sit for 2 minutes b4 use....I kinda wanna fill and vape, not fill and wait
Holding 4mls of juice is great, but if you can't vape 1ml of juice at the bottom of your tank it sucks. You can't vape the last ml of juice because the coil head sits to high so it can't wick the remaining juice.
I did find that when I put the Atlantis coil head in that the wicking was alot better then the coils that it came with, now this could be bc I am using a high vg juice.

So let's talk price....I bought this at a B&M so I paid A LOT more then what I've found online.
My price was $45.00
I have found these online for as little as $23.00
and for this price I would probably buy it again, not for $45.00
Iv'e been vaping on this for about a week now, I've gone through 2 coil heads in 4 days & now put the Atlantis coil head in it and am having better luck with it.
So there's my thoughts on my new clearomizer.  

Hey all,

So, I've been really happy with my new setup (iStick 50w and 30w, Nautilus and Mini Nautilus). Everything has been working smoothly, but I have a problem with the replacement coils I purchased (and cannot return).

Went to go change out the coil in one of my tanks this evening. Filled the tank up as usual, made sure the air shaft and drip tip were clean, screwed on my new coil, filled the tank, and let it sit and wick up for half an hour. Took some pulls without firing, dropped it to 8w (to "step up" and prime the new coil), and immediately got a nasty burnt hit that I can still taste an hour later. Unscrewed the tank to see what was wrong, and noticed the wicking material was bone dry.

For the longest time, I could not figure out what happened, why it wasn't wicking...until I looked closer. The e-liquid holes on the replacement coil I have are TINY! The coils that came with the tanks have holes that are at least twice, maybe three times the diameter. The holes are so small that my e-liquid will not even enter them to soak the wicking material. I checked the serial number scratch off on Aspire's site and both boxes of replacement coils I have came up as authentic.

I'm displeased. $22 down the drain, now I have to rush and find a dealer who has the "correct" coils. I cannot use these coils whatsoever, and the dealer I purchased from does not accepted returns on atomizers.



On the left is the coil that came with the tank (both of my tanks came with this exact same coil, and two replacements that look exactly like it, but I've used them up and am on the new ones). On the right, the coil I purchased in a replacement pack of 5. You can see they look nearly identical, except for the size of the wicking holes. Also, the piece at the bottom seems a bit more flimsy, as you can see in the picture, it's not exactly straight with the rest of the atomizer.

So, can anyone point me to a dealer that has the coils I need? I'm afraid of ordering from somewhere and getting the ones on the right, which are useless and do not soak up any e-liquid whatsoever.  

My main go-to setups these days are Nautilus tanks (both sizes) with 1.8ohm BVC's on mini boxes like Eleaf iStick and Heatvape Defender, but since I got the Defender and it can go down to 0.5ohm with it's 25 watts I decided to give it a go.

So I recently purchased a 22mm Peakomizer 2 Mega tank with Aspire Atlantis 0.5ohm coil and just recently tried it out around 25 watts with my favorite 70/30 vanilla flavor juice.

Now maybe this is partly to do with the tank I bought but even on the tightest airflow setting I feel like it's just too much. It seems to kind of force me to do deep straight-to-lung hits and I'm just not into the experience. I like mouth-to-lung hits focused on flavor more than anything else and I don't typically inhale too deep, for more of a smooth creamy vape. But this experience was more like harsher throaty big airy inhale and I didn't dig it.

After literally just 30 minutes of checking it out I went right back to my Nautty's with 1.8 ohm BVC's between 7.5 to 10 watts and that's a happy place for me, so I'm probably going to sell the barely touched Peakomizer 2 tank and brand new Atlantis .5 coils (looking forward to getting access to Classifieds section here soon).

But still I'm interested in other vaper's thoughts on this. I'm curious to know if sub-ohming is mainly geared toward heavy lung hits and the airy experience I had or if there are ways to do it / certain gear to use so that it's a similar experience to what I'm used to.

As always, I'm just really curious to read the opinions and experiences of others. It helps me learn something new every day!