Smok Xpro M65 Problems

hi my smok 22 vape pen button is jammed in so the top bit is fully pushing in and the bottom is fully not pushed in. it’s not firing or anything when i don’t want it to so that’s good but it also won’t fire at all. idk how to add images  

Right now I have a few box mods, the IPv3, SIG 150w and the Snow wolf 200w. I'm using the Snow wolf 200w and honestly I'm not happy with it. I've had the button stick a few times causing it to auto fire and I'm noticing an almost one second delay from when I hit the fire button to when an actual vape starts to kick in (very slow fire up time, and I'm only running dual twisted 26g) on top of that I really dislike that I have to hit the fire button to see how much volts I'm using. I know the SX M class is one of the best out right now, but the fact it's a single battery concerns me because I typically vape between .12-.20 ohms and usually 60-80w (but since getting the derringer it's been 60). I really like the hot, dense flavorful vapes and I wanna make sure if I get the SX M class it'll be able to deliver that.  

I have had a lot of mis fires on my Smokless Owl 25.00 squonker and had to press down extra hard

and sometimes side ways to get it to fire.

I just done some contact cleaning and scraping on the Smokless Owl Button.

I took my wifes Emory board finger nail file thingy and depressed the firing button and held it depressed and rubbed it

across the firing pin and then took a small jewlers screwdriver and scratched it back and forth across the end of the pin and

did the same thing to botton ground pin.

I noticed some black color on the end of the firing pin before I started this cleaning process.

I gently took the screw driver and scratched back and forth across the positive and negative end of the battery just to

take any small film or oxidation from the ends just to make a better connection.

It seems to fire now just like it should with no MISFIRES---mod is now perfect !  

So I recently bought a brand new Vaporesso Gen mod. Normally I stay away from compression/press fit 510 connections but I decided to give the Gen a shot. I've only had it 1 day, and already I've noticed that the 510 connection is raised slightly above the top of the mod and with a tank connected it is slanted towards the back of the mod. From what I can tell the 510 isn't loose at all. But it still slightly worries me. And a couple times I've taken a hit and everything is fine. Then all of the sudden while my finger is still pressing down the fire button it stops firing. Has anyone else experienced this with the Gen?  

Hey guys.. i been vaping for a while and not had this hapen before.. i am using a Hugo Vapor Rader and ot has been working with no problems until today... when i go to use it, when i try to fire, it says high atomizer the first time i push fire button followed by low battery (have tried multiple sets) when i press again. If i persevere and keep attempting to fire it works fine as if there were no problem until the next time i go to use the device when the process repeats.. i have taken the tank apart and cleaned and put back but the issue continues.. anyone have any ideas on what is wrong/what i should do?  

Hello very basic question I love dripping and do it all day my one problem is with the mech mods I have I cannot place them down with out locking them or they fire sometimes anyone know of a good clone that will not fire when placed down maybe one with a recessed button of sort?

I currently have a F U and a Stingray infinity  

Hey everyone. I've noticed that just about every day since I've used it. When I hit the button to fire it, it will fire for a couple secons then stop, and then fires back up again. And it's starting to concern me. Does anyone else have this issue? And how would I go about fixing it?  

Hello everyone I recently purchased an ipv mini v2 and I love it, it is working perfect. I only have one complaint the fire button rattles like crazy and it drives me nuts. To some it's not a big deal but I just don't like it. So do any of you out there know if there is a way for me to fix this? Once again everything else is perfect ohms and all that it's just the fire button. The wattage up and down buttons are supper tight and clicky. Any help would be greatly appreciated. Thanks  

Hi
I got myself second Caliburn and from the start I feel that auto firing is not as fast as my first one, just like a second or so behind. If I use the button it seems to be OK.

Also, it feels more airy. I check the same pod on both devices and first one seems to have a bit more restrictive airflow. Or, due to late auto firing, I am inhaling first clean air instead of vape, and thus, the feeling of less restrictive airflow.

And lastly, which is not a problem, but it is not feeling OK, second Caliburn pod latching thing feels more loose, where on the first, when I push pod into the slot, I can feel and hear distinctive click, on the second, just a very little bump and very shallow click.

Would first, auto fire delay constitute good grounds for warranty replacement? I got it less than a week ago.

Any thoughts?  

Hello,
I own the SMOK Infinix for more than 3 months now. I change the cotton myself for the pod and started having issues with the device.

After 2 months it would fire a while after pulling. Fixed by cleaning the inside of the device and removing the paper cover on the sensor. Worked perfectly.

Now, few days ago, I noticed I had to pull harder for the device to activate.

And now, literally an hour ago it would stop pulling. Isolated the airflow for a tighter pull worked for couple of minutes, now it just stopped. After some blows from the charging port it would do the infinite firing bug and that's the only way I can get a hit. Please help.

P.s I did clean the inside of the device again as much as I could. It gets a really good connection, just won't fire.