Usa Ohm Meters - New 3d Printed Meters

I'm not that fond of VW because I find most inboard ohm meters are all over the place. It's either low or way too high. I know, the resistance changes as to the voltage applied, but I don't find it so convenient as VV. As for now is mostly vape by taste, and I can never be sure if it's going to be good or mediocre, just depending on the ohm readout. Just now, an 1.8 ohm head Nautilus is reading 2.5 on my iStick 30, 1.7 on my IPV mini and 2.0 on the Sigelei mini. I just can't understand how you can vape on this, I thought it was my rebuildables, but no, it's the onboard ohm meter.  

sorry for newbie question I tonight dove into the RDA world and bought a derringer some wire and a smok ohm meter, I have a hcigar hb 50 and my dual coil build on the HB shows .05, when I try to check it on the ohm meter all I see is 3 dashes no reading at all what am I doing wrong with the ohm meter.  

Hi all,

I have a quick question - I have been getting some inaccurate readings on my coils and I'm trying to figure out which is the closest to the real reading. I have an ohm reader I purchased at Mad Vapes that reads my coil at 1.93. I bought a new ohm meter from USA Ohm Meter (?) that reads it at 2.05. The Cloupor Mini reads it at 1.81 and the HCigar Heart beat reads at 1.83. Provari reads at 1.9. It is 8 wraps of 30 gauge Kanthal. Do any of these numbers even sound accurate?  

What's the difference between 504 and 304 stainless steel? And how does it effect vaping? It seems like those are the 2 that rdas are made out of most I think but yeah thanks!  

8/9 wraps of AWG 29 Kanthal on 2mm bit should give you around 1.8 ohms, right? At least that is what it has always given me. This evening I was rebuilding a Nautilus BVC like I have done so many times before. Lo and behold I put the coil on the ohm meter and it's reading 0.18. I look for sticking out bits of wire. None. I throw out the coil and start over with exactly the same build as always. Again I get 0.16 ohms. I test it on all my regulated mods... same result on all of them.

How is this even possible?!  

I just Started rebuilding my kanger dual coils and im having a issue , seems like when i build them and check my ohms on my meter they are right where i want them but when i put them in my tank and fire them up the ohms fluxuate like crazy from low to high ohms, any idea why it happens ? It occurs even when i build single coils. Anyway to fix this? Thanks  

Mod shows in tc mode to choose
Ss ti ni mi

Ss = stainless steel
Ti = titanium
Ni = nickel???
Mi = ??????????? Nichrome????? Wut is dat tingy  

So I finally got around to putting a coil on the rba deck...my typical kayfun build, 28 ga @ 1.3-1.4 ohms. Everything looked good, coil tight....raised off the deck...screwed into the ohm meter....weirdness ensues....said 3.85 ohms...took it off, put it back on...said 4.6 ohms....looked to see if the coil screws were tight ...check. both tails tight under the screws...check. The coil deck screwed into the base...yep. No moisture in the base, nope. Put it on the ipv...said 7.7 ohms, then 4.2, then 3.90.............


Put the stock coils in the base, everything normal. Is there something I could be missing in the coil deck??? I got nothing else. No, I had not put the chimney on, so no short there. I may wrap another coil and see....I can only think that something is amiss in that little coil deck....or I am missing something in the build that is obvious. It's a really nice, tight looking coil too.  

Hi

I recently purchased the eleaf istick which I use with the kangertech subtank.

While I am impressed with the vapour production, I find it way too harsh and hot. On the coil it has the recommonded setting printed between 15 - 30w. I'm at 15w, but I'm still finding it too hot and harsh.

My question is:

is it safe to go down all the way to 11w or even possibly 8. I am confused as I've heard this could short my device or cause injury e.g device exploding, fire...

Thanks  

Hi guys,

Is it really normal for an atomizer to get hot especially when using dual coils?
I just created a dual coil a couple of minutes ago using 24 gauge kanthal wire, 10 wraps each on a 2.4mm precision screw driver. My meter shows that the resistance is at 0.4 ohms, being curious and all since this is the first time that I made a dual coil, i decided to test it out.
Got some good flavor and vapor, though the vapor is warmer than I would want it to be ( I prefer cold vapor)

After taking a couple of 5 secs drag, I notice that my atomizer became hot, not warm, but hot. Is this something that I should be concerned about? I am doing something wrong or have I done something wrong when creating my coils?
Please help.

Here are some pictures of my device and atomizer. ( Philbox wood mod running on 2 pcs of AWT 18650 2600mah battery, my atty is Haze by vapehead origins)