Battery Revival

I bought my Sigelei 100w Plus a few days back and ordered 2 Sony VTC4's on my same order (I'm confident they're legitimate, I've bought some before) to be able to marry them together and use them with my Sigelei. Upon receiving the batteries, I labelled one A, and one B and put them into my charger at the same time (charger was off, put both in and turned it on), one battery is slightly more charged than the other (it's 2/3 bars, while the other is still 1/3). I'm a bit worried about using married batteries, I understand rotating A and B in my Sigelei and charger but will they be the same charge when they're done? They're new batteries and they both went on at the same time yet one of them is charging a little bit faster.

When both of the batteries are fully charged, will they be safe to use and cycle accordingly? I heard about if one battery has even a tiny bit less, the batteries will take an uneven load and it will make it risky. How do I ensure that these batteries remain married?  

Hey Guys,

I have been wanting to use a mech mod for quite some time now. But I didn’t want to rush into things, given that they can be dangerous if not used properly.

To prepare I have studied ohm’s law and have a pretty decent grasp on it. And have a calculator app on my phone.

I have checked out Mooch’s battery recommendations and have a good idea of what batteries to use and which to avoid.

I still do have a few questions I was hoping an experienced Mech user could help me answer:

- What would be the “sweet spot” as far as resistance and safety go for a dual coil set up? Obviously I want to go as low as possible and have a hard hitting vape. But I also want to be safe. I plan to use a dual 18650 Parallel mod (The Clutch X18). I would be most likely be using Sony Murata batteries as I cant find any Samsungs where i live. I’m thinking somewhere around 0.17-0.2? Or would it be safe to go lower than that? I will of course test my build on an ohm reader and regulated mod before throwing it on the mech to be safe.

- Are there any other general safety tips? Ive heard that you want to screw the Atty down all the way first, before inserting the batteries. And then insert the batteries. And when removing the batteries i heard you want to slightly unscrew the atty first, and then carefully remove the batteries? Can anyone please confirm if this is correct.

- Is its safe to chain vape on a dual 18650 parallel mod? When I say chain vape I mean like maybe taking 5-6 big hits back to back. Then waiting 3-5 minutes, dripping some juice and then doing another 5-6 hits.

- Is there anything I should be monitoring while I’m vaping? Like the heat of the batteries? From what I’ve read, the batteries drain quite fast on a mech. And after some experience you will just kind of know when they need charging because the vape experience changes. Is there anything I’m missing? Or something i should be looking out for?

- I can only vape in my kitchen. And sometimes there might be a little bit of water on the counter from someone’s drink sweating, or drops after someone washed their hands etc. Is this a risk? I will of course do my best to keep all surfaces dry. I’m not talking about large amounts of water or submerging or getting the mod really wet. But just what one might find on a kitchen counter.

- Any other tips you could throw my way would be great!

Thanks in advance!  

Is it safe to use the vaporesso revenger (built in batteries) and the vaporesso revenger mini (lights up) after owing it for three years? It seems to have kept 3/4 battery charge and I have not used them in a year and a half. I ask because I’ve read older batteries can be dangerous to use if they have low voltage or something.

Also is it safe to use Sony lithium ion batteries after 2 1/2 years? Their volts was at 3.6 when I started charging them. I haven’t used them in a year and a half, but I did charge them once during the year. Using them in arrow sense mod.  

I've been vaping for almost a year; mainly regulated VW mods. Recently I discovered my affinity for Mech Mods and, in the interest of battery safety, I am having a tough time telling when I should swap out my batteries. I've heard that it's not a good thing to over-discharge them, but how can you tell if/when that might be happening? I tend to err on the paranoid side and swap them out every couple of hours or so. Any tips about this? Is it just kind of a "feel" thing learned with experience?

Thanks!

tre  

Here while back I'd purchased a bunch of 18650 batteries.
Mostly LG H2 & 4's. Samesungs, Panasonics and what I'd thought was Sony.
But found out they are cloned.
So I just sit them to the side and thought oh well.
Anyhow, i have a few extra regulated box mods & thought that I'd try some of these cloned Sonys.
They seem to work and last just as long as my other batteries.
My question, has anyone ever found out what these cloned batteries actually are?
I've been keeping a close watch on these fake Sonys.
No issues so far.

Jim  

So I've been vaping now for almost 5 months. I own 4 different regulated mods, many sub ohm tanks and a few rda's. I'm wanting to pick up a mech mod, but not sure which would be better. I'm pretty much looking at either the nemesis clone or the stingray x clone. Any thoughts on which is better, or any other mechs that I may want to look into?  

Hey guys,

I finally updated my charger a few days ago (I think before I had the VP2) or something like that. Quick question on something I'm noticing that seems a bit odd to me.

When I charge (for example 18650's), a battery that's fully charged in channel 1...it flashes FULL/0.00 mA, I remove the battery. A few minutes later, I'll put the battery back in the same bay, and all of a sudden there are a few hundred mA's that show up on the screen that need to be charged back into the battery and it takes a few minutes for channel 1 to recognize the battery is fully charged and flash FULL/0.00mA again (although it does show above that's fully charged at 4.2v).

If I take that same battery and do the same test but this time in channel 2, within a few seconds it recognizes that the battery is fully charged and flashes FULL/0.00mA. So it seems channel 1 is not working as well as channel 2 is, when it comes to recognizing information from the battery.

Is this normal for this charger or do I have a defective charger?  

Wismec 3 Battery? No good. Breaks within a year without dropping. Replicated on two mods.

Wismec 2/3 mod? Yet again, poor manufacturing. Wires not soldered properly. Almost lasted a year.

Squid Industries Double-Barrel? Craps out after 1 month without any damage. Wont turn on.

GeekVape Aegis Legend? 2 months and not reading the batteries right. Never so much as tipped over on my desk.

SMOK? Had more than I can count or bother to recall the exact models, but every one busted within a year.

None of them seem true to their warranties either. They make it as tedious a process as possible. I haven't tried with the Aegis Legend yet, but I'm going to go out on a limb here and say it's probably more of the same.

At this point, I am convinced that I have spent more money on mods than I have on juice. These mods are all made like crap. I don't want to spend $80 every few months to get a new mod. I just want to vape for gods sake.

Has anyone had a mod that has lasted them over a year? What kind was it? I've asked this before and that's what led me to the Double-Barrel and the Aegis Legend. Both have failed on me even sooner than my previous attempts.  

Okay so I did look this up and it appears that other people have mentioned this specifically with sigelei mods but I didn't see any that were more recent. I look at my mod to see what my batteries charge looks like to see if I need to go ahead and change batteries and I swear to God the thing starts jumping around as though the batteries are charging themselves and then going back to the 40%. Apparently that's a problem that the mods have and isn't something to be concerned about but it freaked me the heck out. They're doing just fine now that they're in their external charger thingy but I just want to make sure that that's not a sign of something going wrong with the batteries that it's just my mod being weird I've checked the connections and everything to make sure it was clean and that the batteries were fine and not dented or unwrapped and everything looks good. I just need some assurance that the batteries were not like failing or that a regulated mod would shut itself off if batteries were jumping around like crazy in reality if that's even possible
For clarification it was doing this when I was not firing it  

Hi
I'm usually vaping at just 14 watt (mouth to lung, nothing heavy).

Now I'm soon getting a new mod that takes 21700 batteries, so I'm searching for the best batteries without spending too much or too little.
(aiming for Samsung, LG or Sony, to be safe)

I see some batteries hold 5000 mah, like the Samsung 50E (cyan).
But it only has about 10 amp discharge rate.
So less than half than "regular" 4000 mah batteries for example.

Is 10 amp more than enough for vaping at just 14 watts, or should I find a more "high-drain" battery?
I want to be safe and avoid risks or heat.