Apv/mech Mod Heat

over the past month or so i have gradually moved into RDAs as opposed to RTAs/Cartos. most of my builds typically come out anywhere between .24-.45 ohm, dual coils. i bounce back and forth between my SMPL mech mod and my ipv mini II.

on the ipv mini II i'll take anywhere between 4-8 pulls between 30-50 watts when i get a "too hot!" message on the display. this has happened to me about 8-10 times already over the past two weeks or so. has anyone else with this device, or one similar, have this happen before?

on the SMPL mech mod i notice the top of the mod and the atty getting hot pretty darn quick when i have something like a .34/.37 ohm build on it. once it gets hot like that i just stop because obviously i don't want it to blow up in my face.

i only use 24-28gKA1 as of right since its all i have. i'm waiting on a shipment of some n80 though, hear some good things about that wire.

being 100% honest i am looking for the bigger clouds with good flavor. i did some searching around on here and found some decent stuff that is helping me figure everything out.

anyone got any ideas on the routes i should take to avoid this over heating and being able to get good dense clouds?

edit: i use sony vtc4's and vappower 2500mah 35amp batteries which i bought from vapehappy.  


Similar Content



I Think I’m Ready For Mech Mods!

Hey Guys,

I have been wanting to use a mech mod for quite some time now. But I didn’t want to rush into things, given that they can be dangerous if not used properly.

To prepare I have studied ohm’s law and have a pretty decent grasp on it. And have a calculator app on my phone.

I have checked out Mooch’s battery recommendations and have a good idea of what batteries to use and which to avoid.

I still do have a few questions I was hoping an experienced Mech user could help me answer:

- What would be the “sweet spot” as far as resistance and safety go for a dual coil set up? Obviously I want to go as low as possible and have a hard hitting vape. But I also want to be safe. I plan to use a dual 18650 Parallel mod (The Clutch X18). I would be most likely be using Sony Murata batteries as I cant find any Samsungs where i live. I’m thinking somewhere around 0.17-0.2? Or would it be safe to go lower than that? I will of course test my build on an ohm reader and regulated mod before throwing it on the mech to be safe.

- Are there any other general safety tips? Ive heard that you want to screw the Atty down all the way first, before inserting the batteries. And then insert the batteries. And when removing the batteries i heard you want to slightly unscrew the atty first, and then carefully remove the batteries? Can anyone please confirm if this is correct.

- Is its safe to chain vape on a dual 18650 parallel mod? When I say chain vape I mean like maybe taking 5-6 big hits back to back. Then waiting 3-5 minutes, dripping some juice and then doing another 5-6 hits.

- Is there anything I should be monitoring while I’m vaping? Like the heat of the batteries? From what I’ve read, the batteries drain quite fast on a mech. And after some experience you will just kind of know when they need charging because the vape experience changes. Is there anything I’m missing? Or something i should be looking out for?

- I can only vape in my kitchen. And sometimes there might be a little bit of water on the counter from someone’s drink sweating, or drops after someone washed their hands etc. Is this a risk? I will of course do my best to keep all surfaces dry. I’m not talking about large amounts of water or submerging or getting the mod really wet. But just what one might find on a kitchen counter.

- Any other tips you could throw my way would be great!

Thanks in advance!  

Years Later I Finally Find The Closest Vape To A Cigarette.

I've been vaping in subohm territory on bigger (non cigalikes) mods for the past year or so, on 0.3-0.7 coils regularly with VV/VW mods only with a range of 30-40watts. I started looking for mech mods recently and picked some up, then picked me up some VTC4's. After trying to figure out builds and such, I discovered Nichrome 80 (I exclusively used Kanthal A1). Come to find out Nichrome 80 is more malleable, and doesnt last as long as Kanthal, I was deterred but looked more into it. The rampup time on Nichrome seems to be much quicker, and the Nichrome 80 gives less resistance per ft compared to Kanthal A1 (same gauge). Recently I've been vaping 0.17-0.3ohm coils and Its the closest thing to a quick drag form a lit cigarette ive ever vaped.

0.17ohms on a mech w/ sony vtc4


I believe I will be purchasing a sigelei 100w soon, so I wont have to 'build for the mod'. 100W vaping is pretty nice not having to take 3+sec long drags, with 0 rampup time. So yeah, I get why the sigelei mods are popular now. I didnt really bash on em I just never understood them, but now I do . Short, Quick, Drags. Very satisfying.  

A Smpl Explosion.


DSC_0137_resize by Papillon61 posted May 31, 2015 at 3:30 PM


This could have been my face this morning - luckily it was my thigh! I'm still shaking. Also luckily I was wearing thick cotton slacks - don't know what would have happened if I had been wearing something synthetic because there was fire.


DSC_0128_resize by Papillon61 posted May 31, 2015 at 3:28 PM


This is the result of what I suppose you would call venting of and IMR supposedly perfectly good Efest battery which exploded inside my SMPL mech mod. This was a battery I had been happily using for the past 10 days or so on a mod that I received yesterday and which worked perfectly fine all day yesterday using the same battery or its twin since I got a pack of two.

This is the state of my desk right after the explosion.

I'm having trouble adding pictures but there are more.... I need to figure it out and I'll be back.  

Someone Help Me.

Hello everyone. I have a problem. I'm gonna need some help to get through this, I may not even make it. Who knows?

I'm addicted. Not the good kind. The kind that costs money... The kind that makes my long hours at work perish with the swipe of my debit card... I'm addicted to.. Upgrading.

So I'm in need some some help from the best of the best with you guys. I'm looking to upgrade! I'm currently looking into going from my istick50w and Subtank Mini, to a mech mod and rda. I'm gonna start my way with single coil builds, and go up to dual. I am thinking I have about $100 I want to work with, so can someone make some recommendations?!

I already have some cotton and kanthal from my rba with the subtank. I'm just looking for a good starter mech and battery set up, with a pretty decent rda. Now, since this is my first, I'm not biased at all against clones. I welcome them! As long as they are decent quality and get the job done, so be it!

But here's one catch: I don't really like shiny stuff, oddly enough. I mean brass, or really shiny silver. I don't like scratches that stuff seem to get in my pocket. I love stuff to look perfect all the time!

So any help or recommendations are greatly appreciated! I have no idea about batteries or their chargers, but I'm more than willing to educate myself.  

What To Buy Next?

A quick back story to start. I was a 1-2 PAD smoker for about 5 years. I found vapes and quit smoking. I was able to stop vaping and smoking for 18 months until I picked up smoking again for a few years. I have once again been able to stop smoking and started vaping again. Simple transition, some willpower for sure, but I have kicked the habit completely. When I started vaping again I purchased an Istick 50w and a troll. Have been using 3mg liquid only. It's been about six weeks smoke free again and I want to, not only upgrade, but reward myself. I read and read and watch reviews non stop, my head hurts from all of the stuff out now. I use my mod consistently at 45 to 50 watts. I have a 0.4 dual coil build and a chuff top. The heat from the vape is less than perfect, but I like the vapor production. I am interested in temperature control as well. If I need to buy two mods to have everything I want, so be it. Not that money isn't an issue, but right now it isn't a factor. I have been looking at IPV3, Sigeli 150, IPV4, Mech Mods, you name it I have looked and can probably tell you the specs off the top of my head. I just can't decide! I need your help ECF! I know I want at least dual 18650, as my Istick lasts maybe half a day until I need to charge. Good flavor and large vapor production atty, temp control, and good ergonomics. Thanks in advance for all input and help.  

Mech Mod Coil Build

Hi. I have just purchased the heavy hitter mech mod.
The coils I bought are wotofo .28 dual core fused claptons.
It is a asgard mini RDA, it will be a dual coil build , so resistance should be .14
Will a Samsung 40t battery be ok with this build.
In regards to saftey and amp draw.
Thanks  

Non-smokers Starting Vaping - Disturbing To Me

I've been away from ECF for awhile but due to the influx of new devices, I recently returned (and got a bunch of new vape gear, but that's another story ).

Was just browsing the New Members forum and I am very disturbed by the amount of posts being made by people who have never smoked asking for advice on how to "blow clouds", "get into vaping" or even "get a better buzz" from vaping.

Of course, the vast majority of replies in these threads are from knowledgeable and helpful ECF'ers telling these poor, ignorant folks that it's probably a bad idea to start vaping 36mg juice in a sub-ohm device if you've never smoked...and that is great!

I just can't help to think that all these young (I'm assuming) non-smokers taking up vaping and "blowing clouds" can't be good for our cause and I find it quite disturbing.


FULL DISCLOSU I currently vape on an SX Mini / Goliath @ .4 ohms and can blow some pretty good clouds, but that's not what it's all about for me...it's about staying off the ciggies.  

Hard To Use A Tank Again?

I searched long and hard for my perfect vape...and I sort of found it. I have a REO with an RM2, a dual 18650 mech, and now a SMPL mod. I also have a derringer, MXv3, hobo, and magma. I've been using the REO and drippers almost exclusively with the exception of my "morning vape" in an EVOD/eGo combo. I tried using my subtanks on my VF clone the other day and just can't seem to dial them in to taste good anymore. I either fry a coil or the juice that use to taste good in them doesn't anymore (or I can't find the sweet spot). I'm using the 0.5ohm coils in the subtanks. I run anywhere between 0.5 and 1.2 ohms in my drippers with 26g or 28g.
Did anyone else run into this problem or is it just me?


Sent from my iPhone using Tapatalk  

My Complete Setup (mod, Rda, And Juice)

Hey everyone, I just wanted to post my setup here, nothing to fancy so just take a quick look and feel free to leave a comment or reply.

To kick things off I've got a Seeker Mech Mod by EHPRO. It's a sleek design, all copper, and easy to press button. Little short and thick for those of us who like our setups to look beefy.

Atty- The Tobh Atty. It is a pain in the butt to take apart from the get go but once you get a bit of juice on all the O rings it comes apart fairly easy. Good deck to build on all pre-drilled holes on the three posts 1(+) and 2(-) (Obviously). Deep basin to hold plenty of juice for our drip and drivers safety. My current build is a dual single coil coming in at 0.28 ohms. Using a regular cotton wick.

Juice- "Bliss" made by The Artisan Vapor 100%VG This juice is an explosive flavor of fruits, and for being 100%VG it has a heavy flavor. 39ml bottle runs at 20$ not to bad for a good juice. When I drip with a full basin it lasts roughly an hour, and I heavily use my vape.

Battery- This thing is one of the best right now but I'm still limited on what builds I can do. My 0.28 is safe, however my 0.22 is unsafe (Go figure) ANYWAYS! (Specs) MNKE IMR-26650 3.7(low) 4.2(High) 3500mAh.

So I think that's all. Thanks for reading guess, and questions or comments just drop it down below. Goodbye and VAPE ON!
 

Battery Revival

Herro!

So, I always used to use mech mods from about 6 months to a year and a half into vaping. For the last 6 months I've been on regulated (iStick 30W and 50W).

When I switched to regulated I retired my mech mods and 18650 batteries to the closet. I made sure they were all around 50% charged because I heard from someone on here that was the best condition to leave them.

Well recently I've had this curiosity to try them again, only for at home use, mainly for the novelty of it.

So, my question is, what will I have to do to revive these batteries? Are they safe to just throw back on the charger and use when fully charged? Or are they not safe to use?

Batteries: 4 Sony VTC 4's (all were acquired about a month before I stopped using mechs), 2 XTAR (Sony) VTC 4's (about a year old now) , 2 MXJO 2500mah (20A LG's) (about a year old now).

Let me know! Thank you!

Vape Happy,
Cullin Kin