Looking To Get A New Box Mod In The Future.

Hello Been vaping about 2 years now
My setups are Vaporshark Rdna 30 Istick 30 watt and a provari 2.5 and a IPv mini v2 30 watt
So like many others I have been juggling with wattage I currently Use A couple of kanger subtank minis using the RBA and a kayfun v4 I've been all over the place building ohms but have settled on 1.2 - 1.4 ohms BTW I'm not into sub ohms
So after many months of different ohms and watts with the help of steam engine I have found I like my vape at a heat flux of around 175 so to get to this and I can't believe how simple it was I just take the ohms I am using such as 1.2 @ 12 watts = 178 heat flux 1.3 @ 13 watts = 178 heat flux and so on I can't believe it became that simple
So I suppose all it takes is to find what heat flux you enjoy and adjust from there
I never bought that what I have read thru the last 2 years that 14 watts is 14 watts no matter what ohms you use it seems to me there had to be more factors involved
Just my thoughts


Sent from my iPhone using Tapatalk  

a few little questions. I actually like dripping my 3 mg nic in max better even than vaping. I drip using 3 mg nic on a Istick 50 watt set about 23 watts with a draw of about 2.5 seconds and the coils reading says 1.6 ohms and the air holes blocked a tad on the el diablo bael. I vape on the Istick 20 watts somewhere around 7 to 8 watts on factory coil of 1.8 in a nautilaus mini
my questions: 1) does sub ohm in a rebuildable tank give flavour similar to a dripper
drippers seem to require higher watts is this in anyway suggested as less healthy ( I am not too concerned about the increased supposed formaldehyde issue I believe Dr F had issue with the research and in my opinion I probably breathe more formaldehyde off gassing wandering around carpets and insulation and pressboard)
2) the nic level is quite a bit lower in the dripper Does this actually translate to a drop in nicotine/contine levels in my blood in other words would I need to drip more to keep my nic levels somewhat reasonable re setting off " the I want a smoke brain run"
3 if I were to drip only for 3 or 4 days am I likely to find my 12 mg vape to strong

thanks for any insight you might provide  

So I decided to try a 1,6 ohm coil on kayfun v4 clone Tobecco and I am using 28gauge Kanthal with a cotton
wick on a Rdna 30 and its vaping well at 15 watts I have a kanger subtank mini coming in the mail and here goes my question
So the kanger subtank states that with a .5 ohm coil i could vape up to 30 watts but the voltage comes in at like 3.8 volts
I was under the impression that the rdna 30 needs at least 4 volts to work which kinda brings me to my second question
What is the point of of sub ohms? cant i just build a 2.0 ohm coil or something like that to achieve the results as if i was subohming
I am very confused on this
thanks for the replys in advance
Oh yea is a 1.6 ohm coil at 15 watts a normal build or any recommendations for the kayfun v4 for watts and ohms thanks again  

So....my lemo was my #1 RTA, until I got the subtank mini and delta 2 (although I haven't tried the delta 2 yet, but have heard very good things about it). I have been sad, because I have put my lemo to the side, because my newer RTAs have more airflow. I would vape my lemo most of the time between 25-30 watts, and could get it up to about 38 watts without a dry/burnt hit. Anything over 40 would give me a dry/burnt hit, which is still impressive. (with my old wicking method)

Long story short, I decided to drill out my airholes on my lemo. I found another guy that had already done this, so I followed his bit sizes. He claims that he now vapes his lemo around 70-80 watts without dry/burnt hits. I had my wisdom teeth out about 3 days ago, so I can not vape as I usually do (in fear of getting a dry socket) so I have had to barely hit my tanks to vape. I hit the lemo, after modding it, last night, at 40 watts with a wussy vape and no dry/burnt hit at all. I can't wait to actually vape like I usually do and see how high in wattage I can go. By the way, I am trying something new and using Drip Trippers pancake wicking method on this as well, and a 0.78 build.

So here are the pics, with the sizes, if anyone wants to do this. It took me about 15 minutes:



4 External air holes (pic 1) - 3/32 drill bit



Vertical stem shaft air hole (pic 2) - 1/8 drill bit


Vertical stem 4 air holes (pic 3) - 3/32 drill bit


Pancake wicking method.

 

Hey guys if i was to use the cloupor mini 30 watt regulated device with an efest imr 18650 35a
battery am i safe? will the cloupor see any overheating of the battery if it were to happen? or will it see if the ohms are too low? the lowest ohms i plan on using is .8 possibly .6 but i just wanted to know how safe is this device? also i am aware of the recall on this i will be doing the "too hot" test on it. thanks for your replys!  

I'm new to rda's and getting into ☁ chasing, first of all. I've had my mutation x v3 for about 2 weeks now. I'm using a istick30w. I'm looking for something that will read lower ohm builds (exp: 0.2-0.4), and easily be able to push them(I'm thinking 75w+). Since I'm still new I think it'll need to regulated. Don't think I'm ready to go up to unregulated.  

Somehow, I inadvertently pushed the buttons just wrong today and it went from 7 watts (my usual power setting) to 50 watts (the highest setting). I didn't even mean to push any of those buttons.

I experienced instant burnout and a horrible taste in my mouth and the coil was instantly ruined.

Do people really vape at such high power? If so, how often do you have to replace the coil? And how many ohms are you putting that through? The coil I replaced it with is 1.77 ohms which is about the same as the one I burned out.

50 watts seems so excessive to me that I double-checked and yes, that's what it says it goes up to. Even at 7.5 watts the coils seem to burn out too fast which is why I vape at 7.

I feel like Nigel Tufnel designed this thing. "But it goes to 50. That's 43 higher than 7. So it's like 43 more. So when you're vaping at 7 watts and you want that extra push over the cliff..."

(I'm actually impressed that Nigel could do the math to figure that 50 was 43 higher than 7)  

Finally! I've tried so many sub ohm tanks with a shelf of them to prove it along with box mods and I've found my perfect set up that I'm 100 percent happy with. That urge of "must have more" and "must have the latest and greatest" has finally subsided after 100s of dollars spent. I can finally relax on hardware and focus on enjoying good juices. I still stay up on new tech but I'm finally happy on my go to juice vendor and hardware. Oh what a good feeling!

My goto set up: Atlantis V1 with cotton coils and 5ml upgrade and ipv mini 2 at 32 watts. Any higher then 32 and the vape is too warm to enjoy. To justify this, I personally own the following:

Atlantis V2
Subtank
Subtank mini using both Occ and rba
Delta I I using both coil and rba
Lemo
Lemo 2
Arctic tank
Starre tank
Herakles tank
Kayfun
Kay fun v4

Ipv mini 1
Istick 30
Istick 20
M50 with 65w upgrade

My go to juices are all from itcvapes. 20$ for 120ml for the win.

Time to sell off old items or give them to friends to help them quit smoking.

FYI I'm so busy that rebuilding isn't an option for me. It's much Cheaper, and I have a ton of kanthal in different gauges with a big bag of Koh Gen do, but I'd rather pay for convenience of coils.

Wonderful feeling!  

I am running my Kanger Subtank mini rba deck on .9 ohm (spaced 4 wrap 28awg IIRC) at 13 watts and it is cloudy and flavorful. The OCCs were fine but I prefer the rba I think (even though I'm still a bit of a build novice). Many others seem to run it at 25+ watts and lower resistance. I had it at .5 Ω and ~19 watts was good, had dry hits above 23 watts. Now have dry hits above 15 watts at .9 Ω. I'm still playing around, but this current build/wattage is working awesome.

Other important factors:
Tobacco and vanilla DIY juice 4mg 50/50 PG/VG Organic cotton, standard wick Only had Subtank for 3 weeks Coming from BCC clearos Been vaping for 6 years Used to be mouth-to-lung, doing a lot of direct lung but still switching back sometimes What's your style with the Subtank? How are you running it? What's your wick-style? Dry hits? Wattage? Ω?  

Hello im looking for a RDA, I have had a shop around and I have narrowed it down to a few, the tobh atty, plume veil, magma and the dark horse dripper. I am more leaning towards the tobh atty as personally it looks the more simple to build on. I will be trying to build .5 ohm coils as that's what im using at the moment (aspire Atlantis) could you give me any advice/recommendations