Where Can I Find Allen (hex) Screws For Rda? Forge V2 By Mcv

Hi All, Can anyone help me with finding the size of the deck screws for mounting the coil? I want to replace them with grub screws but have no idea what size to purchase. Any help would be appreciated.

Thanks  

I got an authentic yep RDA off rbavaporstore.com. The screws that go into the posts are so long that, with 24 gauge in the post, the screw won't start to screw into place. I got 28ga to fit and I can screw them down but 24 gauge doesn't work. Is there anything I can do to change this?

I was thinking I could sand the screws down or maybe drill the post holes bigger so that the kanthol has more room to be tightened down with the screws

Thanks for any help  

Good tip for you guys without magnetic back plates on box mods. Throw those crappy screws away!
Most plates are beveled to fit snug to the main body. Instead of having to unscrew those tiny little screws find yourself a rubber wrist bracelet and wrap it around your mod. So simple but very effective. They practically give those things away so it shouldn't be too hard to find one. Or you could buy one.
Try it out! I promise you will love it  

Has anyone tried to sand down their screws that screw into their RDA posts?
If I sand mine down, do you think i will be able to still screw it in or will the threads be messed up  

Hi all, just got home from work and my new Orchid V4 was here waiting on me.
Kinda excited ok, thing is I started building coils for it using 28g wire.
Here the problem, I cant seem to loosen up the four screws on the post.
Are these normal threads or reverse threads?
Cant install new coils till I can loosen up those freaking screws lol.

Thanks, normally I never have such problems.

Jim  

hey guys. i have an ipv3. a couple days ago i asked my friend to screw the back plate on while i was busy doing something else. he somehow managed to tighten the screws so much that the areas of there back plate around the screws got pushed in and now there are small gaps between the back plate and the rest of the device. i tried countless times to straighten the areas out but nothing is working. does anyone know where/how or if its even possible to purchase just a new back plate?  

My mother in law just came home with a new Ecig. She is fairly old, yet insists, no matter how how many people tell her, that Cigarette sized ecigs are NOT economical in the long run. Don't even try to make suggestions, she's really stubborn.

Anyways, she's been off of Cigarettes for a while, and has been using an EGO/Stardust combination for almost 2 years. She said her battery wasn't holding a charge, and decided to pickup a new ecig. She bought something called a Mistic brand ecig...but it has a tank on the end of it. The whole unit is about the size of a normal cigalike. However, the end is a mini tank system. I tried it, and little vapor comes out of it.. which she says is fine. I will say, the products looks nice.

It seems it has a very small battery in it with a smaller than a mini protank II style general configuration for the atomizer. I doubt the thing holds a mil, and I doubt the battery is over 100MaH. The unit screws off the battery, and then the coil and wick unscrews out of the tank. It reveals a setup similar to a mini protank, where the chimney goes into the coil. The coil is TINY. I tried peeking down to see if I can see the coils, but I couldn't. I can't find any sort of specs about the product, type of connector (It's smaller than a 510), battery size/capacity, or even where to buy replacement coils. On the box, there is a website... MysticVapors.com is up for sale!!, but even that site is vague on anything about it and only sells the starter kits. Is there any information about the device anyone knows about? Its a cigalike size with a tank. Can replacement coils be bought? any gotcha's (besides incredibly low amount of vapor) A link to the exact item she bought is HERE. I feel she's just wasted money, but if I tell her that, she just gets all huffy.


Thank you in advance.  

Okay so at the shop we were fixing a coil for my rba nd he went to put subtank on my istick nd it read no atomizer....then he pushed some cotton around n made sure screws were checked again then it worked...any idea y? The whole things been fine since I got it but ohms have jumped some ....  

So I finally got around to putting a coil on the rba deck...my typical kayfun build, 28 ga @ 1.3-1.4 ohms. Everything looked good, coil tight....raised off the deck...screwed into the ohm meter....weirdness ensues....said 3.85 ohms...took it off, put it back on...said 4.6 ohms....looked to see if the coil screws were tight ...check. both tails tight under the screws...check. The coil deck screwed into the base...yep. No moisture in the base, nope. Put it on the ipv...said 7.7 ohms, then 4.2, then 3.90.............


Put the stock coils in the base, everything normal. Is there something I could be missing in the coil deck??? I got nothing else. No, I had not put the chimney on, so no short there. I may wrap another coil and see....I can only think that something is amiss in that little coil deck....or I am missing something in the build that is obvious. It's a really nice, tight looking coil too.  

Last night I received my vaporDNA order:
1 - Doge X by Congrevape
1 - Mutation X V3 by Indulgence
1 - EHPro Pontus V1.5 Dripping Tank Atomizer

I was so excited!! When I ripped open the box I was stunned! The EHPro was sitting right on top in this elegant black box! Quite an impressive sight!!
The Mutation X V3 looks killer too! Nice box, slick looking in the see through window! Was a little disappointed that the Drip Tip that comes with it is PLASTIC. That was a bit disappointing. But this thing looks amazing!
The Doge X - I don't even have words for this thing!! Intimidating comes to mind! The chuff tip (which is NOT removable) on this guy is MASSIVE!!!! MASSIVE (yes I said it again!)!! It almost seems too much!! But very excited to build some coils for this guy and start blowing some clouds!!

It was late last night when I finally got to sit down with them. The only one I was able to clean and get put together was the EHPro Pontus V1.5. Taking it apart was a pain in the, well, in the you know what!! The pyrex glass wouldn't come off the bottom part and every time I would twist and/or pull on it, it felt like the glass was going to Shatter (but it didn't, eventually it popped off). Unfortunately, this dripping tank does NOT come with instructions. So dis-assembly was a little time consuming, trying to figure out which portion to remove and which screws to loose. But thank you YouTube for 1 helpful video.
Anyway, built some 1.6ohm coils out of 28ga Kanthal, was shooting for 0.8ohm final resistance at my atty. Let me tell you, the screws on this thing Do NOT want to HOLD down wire. One constantly backs out and the other just Breaks the Kanthal. And I am not even screwing them down that Hard or "forceful". So after getting the wires in and screws down and wicked, I fired it up but the Atty reads 0.9ohm then JUMPS up to 1.4ohm, then down to 1.0ohm then up to 1.2ohm, then down to 0.9 then up. It won't hold steady! So I took off the top and screwed down that screw that keeps coming out, was fine for a pull or two, then started bouncing around again.
I contacted vaporDNA who I made the purchase from via email (no one seems to answer their customer service phone number) and I also contacted EHPro about it. So we'll see what happens.

VaporDNA, so far is pretty good. Shipped the items on the 12th and I got them on the 16th. So pretty fast shipping (it was FREE!). They even send a FREE bottle of juice along with any purchase! Its 60/40 (VG/PG) and they wrote that that is the Only ratio they'll send for the free juice! Which is fine by me, I don't tend to look "Gift Horses in the Mouth".

Any way, I would post pics but can't while I'm at work! Just wanted to update everybody!!


More updates to come as well, once I get my Doge X and Mutation V3 coiled and wicked!!!