My MVP 20 watt recently started to get a little wonky on me. I use 1.5 ohm coils in an aerotank but for some reason the MVP is readin it as 4.9 and sometimes even higher. Of course its not hitting right either. I know its not the coils because if i put that same tank on my MVP 2.0 it reads correctly. The MVP 20w doesn't do this all the time but today its been doing it all day. It won;t go below 5 ohms and sometimes its even higher. Is this thing shot?
I rebuilt a new coil 1.4 ohms. I am having this issue even with 1.2 ohms I have a 20 watt istick. So I know a lot of people have this harsh hit (not dry just hot) and a longer drip tip solves the problem. But for some reason I am barely getting any vapor production even at a higher watt and open air flow. Anyone have ideas if I am too vague please ask away.
I have the Smok xPro M80 plus and I have a couple Kanger subtank minis I use with it. I usually use .5 ohm coils. Sometimes it will show the ohms fairly correctly at .54 or even .61, which seems close enough. However, as I puff, the ohms reading will tend to change after every few puffs. Sometimes it will even say up to 1.5 or 2.0 ohms on the same tank coil! One tank seems to do it worse than the other, but the two I use now both will change quite often, and once in awhile quite drastically. It sometimes helps if I unscrew the tank and screw it back on, but if it isn't really tight, the ohms read are really far off from what they should be. I'm not sure if it is the tanks or the M80 plus that has the problem. When it reads really high, if I don't catch it before I take a puff, it is horrible and burny-dry, since it thinks the ohms are so high...
Has anyone else had this problem and/or have any ideas as to how it can be fixed??
By the way, I've cleaned the connections and everything thoroughly, so it's not that...
Hello,
After vaping (sub-ohm) quite heavily for many years, I think it's time to quit that and switch back to MTL now.
What's the best/cheap MTL tank, affordable higher stock Ohms coils that use less liquid? I'll up my nic content to 12mg.
Thank you.
GS Air coils/GS 3ml tanks.
I Googlefied this and Did see One place that said A worn out tank could make coils not last as long. (Sounds near fetched to me...)
Can an old tank start Causing premade coils to show Low ohms, like. 05 ohm?
I am pretty sure these are factory coils not FT copycats.
Bruce in Ocala, Fl
I bought a Kanger Subtank and Atlantis V2, but sold them because they just weren't wicking my 100% VG liquid (Velvet Cloud & Gypsy eJuice) well at all. I tried using the atlantis with the .3 ohm coil installed at 70-80W, which was the stated operating range, and found it to be EXTREMELY hot. So hot that the tank quickly heated up to the point of almost burning my lips. The Kanger just burned the wick up at 20W+ with the .5 ohm coil, despite letting it sit filled for a few minutes and priming.
I am very interested in picking up a Royal Hunter, although I've no idea what pre-made coils (i dont want to make my own coils, just dont have the knowledge or time to learn how) and battery to get. VaporDNA sells UD pre-made coils in various resistances, but figuring out what resistance to use, and thus what wattage battery to get is where I am stuck. Not sure if it'd be better to run at lower ohms / higher wattages, or higher ohms / lower wattages. I'm not sure if it's possible to get massive clouds, but a cooler vape at the same time, but that's my aim.
Having a hard time getting my Dead Rabbit rda to stop popping and sputtering. I’m using it on a VT inbox. So far the only thing that’s helped is dropping the power down, but then I lose the flavor. I’ve got two setups and different wattages on both. One is 0.5 ohms at 30W and the other is 0.3 ohms at 50W. Ideas would help. I really enjoy the higher limits of my coils but get tired of the juice spitting in my face.
I have the Istick 50 with a Nautilus tank. 1.7 ohm coil. What would be the highest watt useage recommend for this set up? I read the user manual for the tank and didn't see a max safe watt. I don't want a melt down. I did however notice that once I get above 18 or 19 watts the flavor of the juice starts to diminish. is this something that could be rectified with a different type of coil in the tank that would allow for higher wattage and give a better taste. Or a different mix of juice?
I just Started rebuilding my kanger dual coils and im having a issue , seems like when i build them and check my ohms on my meter they are right where i want them but when i put them in my tank and fire them up the ohms fluxuate like crazy from low to high ohms, any idea why it happens ? It occurs even when i build single coils. Anyway to fix this? Thanks
Hello Been vaping about 2 years now
My setups are Vaporshark Rdna 30 Istick 30 watt and a provari 2.5 and a IPv mini v2 30 watt
So like many others I have been juggling with wattage I currently Use A couple of kanger subtank minis using the RBA and a kayfun v4 I've been all over the place building ohms but have settled on 1.2 - 1.4 ohms BTW I'm not into sub ohms
So after many months of different ohms and watts with the help of steam engine I have found I like my vape at a heat flux of around 175 so to get to this and I can't believe how simple it was I just take the ohms I am using such as 1.2 @ 12 watts = 178 heat flux 1.3 @ 13 watts = 178 heat flux and so on I can't believe it became that simple
So I suppose all it takes is to find what heat flux you enjoy and adjust from there
I never bought that what I have read thru the last 2 years that 14 watts is 14 watts no matter what ohms you use it seems to me there had to be more factors involved
Just my thoughts
Sent from my iPhone using Tapatalk
Hello guys,
I recently purchased a single coil RTA, my first rebuildable experience. I love it!! .
I saw at the shop a double coil RTA and a Double coil RDA, was planning on buying one of them until I thought I only have a 100W mod. Do you guys think it is enough? Are there some specific ohms coils that could make it work etc? Or is a 100W enough? I am new to this so calculating ohms law and all the other stuff I will learn, I just need a answer from the double coilers if you guys use higher wattage mods or not.
Thank you in advance!